EN 60947-5-4:2003
(Main)Low-voltage switchgear and controlgear - Part 5-4: Control circuit devices and switching elements - Method of assessing the performance of low-energy contacts - Special tests
Low-voltage switchgear and controlgear - Part 5-4: Control circuit devices and switching elements - Method of assessing the performance of low-energy contacts - Special tests
IEC 60947-5-4:2002 applies to separable contacts used in the utilization area considered, such as switching elements for control circuits. This standard takes into consideration two rated voltage areas: a) above (and including) 10 V (typically 24 V) where contacts are used for switching loads with possible electrical erosion, such as programmable controller inputs; b) below 10 V (typically 5 V) with negligible electrical erosion, such as electronic circuits. This second edition cancels and replaces the first edition which was issued as a technical report in 1996. It now has the status of an International Standard.
Niederspannungsschaltgeräte - Teil 5-4: Steuergeräte und Schaltelemente - Verfahren zur Abschätzung der Leistungsfähigkeit von Schwachstromkontakten - Besondere Prüfungen
Appareillage à basse tension - Partie 5-4: Appareils et éléments de commutation pour circuits de commande - Méthode d'évaluation des performances des contacts à basse énergie - Essais spéciaux
IEC 60947-5-4:2002 s’applique aux contacts séparables utilisés dans le domaine d’emploi considéré, tels que les éléments de commutation pour les circuits de commande. La présente norme prend en compte deux domaines de tensions assignées: a) tensions supérieures (et égales) à 10 V (typiquement 24 V) pour lesquelles les contacts sont utilisés pour commuter des charges avec possibilité d’érosion électrique, par exemple les entrées d’automates programmables; b) les tensions inférieures à 10 V (typiquement 5 V) pour lesquelles l’érosion électrique des contacts est négligeable, par exemple dans les circuits électroniques. Cette deuxième édition annule et remplace la première édition parue comme rapport technique en 1996. Elle a désormais le statut de norme internationale.
Low-voltage switchgear and controlgear - Part 5-4: Control circuit devices and switching elements - Method of assessing the performance of low-energy contacts - Special tests
Ta del standarda IEC 60947 se uporablja za vtične kontakte, ki se uporabljajo na zadevnem območju uporabe, kot so stikalni elementi za krmilne tokokroge.
Ta standard obravnava dva območja nazivne napetosti:
a) nad (in vključno) 10 V (običajno 24 V), pri čemer se kontakti uporabljajo za preklapljanje obremenitev z možnostjo električne erozije, kot so vhodi programirljivih krmilnikov;
b) pod 10 V (običajno 5 V) z zanemarljivo električno erozijo, kot so elektronska vezja.
Ta standard se ne uporablja za kontakte, ki se uporabljajo v zelo nizkoenergetskem območju merjenja, npr. pri sistemih senzorjev in termospojev.
Cilj tega standarda je predlagati metodo ocenjevanja učinkovitosti nizkoenergetskih kontaktov, ob tem pa podaja:
– uporabne definicije;
– splošna načela preskusnih metod za nadziranje in beleženje delovanja kontaktov pri vsakem postopku uporabe;
– funkcionalne podlage za definicijo splošne opreme za preskušanje;
– prednostne preskusne vrednosti;
– posebne pogoje za preskušanje kontaktov, ki so namenjeni za posebne načine uporabe (kot je preklapljanje vhodov računalnika);
– informacije, ki morajo biti navedene v poročilu o preskusu;
– razlago in predstavitev rezultatov preskusa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60947-5-4:2004
STANDARD
junij 2004
Low-voltage switchgear and controlgear - Part 5-4: Control circuit devices and
switching elements - Method of assessing the performance of low-energy contacts -
Special tests
ICS 29.130.20 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 60947-5-4
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2003
ICS 29.130.20 Supersedes EN 60947-5-4:1997
English version
Low-voltage switchgear and controlgear
Part 5-4: Control circuit devices and switching elements -
Method of assessing the performance of low-energy contacts -
Special tests
(IEC 60947-5-4:2002)
Appareillage à basse tension Niederspannungsschaltgeräte
Partie 5-4: Appareils et éléments Teil 5-4: Steuergeräte und Schaltelemente -
de commutation pour circuits Verfahren zur Abschätzung
de commande - der Leistungsfähigkeit
Méthode d'évaluation des performances von Schwachstromkontakten -
des contacts à basse énergie - Besondere Prüfungen
Essais spéciaux (IEC 60947-5-4:2002)
(CEI 60947-5-4:2002)
This European Standard was approved by CENELEC on 2003-12-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60947-5-4:2003 E
Foreword
The text of the International Standard IEC 60947-5-4:2002, prepared by SC 17B, Low-voltage
switchgear and controlgear, of IEC TC 17, Switchgear and controlgear, was submitted to the Unique
Acceptance Procedure and was approved by CENELEC as EN 60947-5-4 on 2003-12-01.
This European Standard supersedes EN 60947-5-4:1997.
The following dates were fixed:
- latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-12-01
- latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-12-01
Annexes designated "normative" are part of the body of the standard.
In this standard, Annexes A and ZA are normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60947-5-4:2002 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60947-5-4:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068-1 1988 Environmental testing
+ corr. October 1988 Part 1: General and guidance
+ A1 1992 EN 60068-1 1994
IEC 60068-2 Series Environmental testing EN 60068-2 Series
Part 2: Tests HD 323.2 Series
IEC 60605-6 1997 Equipment reliability testing - -
Part 6: Tests for the validity of the
constant failure rate or constant failure
intensity assumptions
IEC 60947-1 1999 Low-voltage switchgear and controlgear EN 60947-1 1999
(mod) Part 1: General rules + corr. October 1999
A1 2000 A1 2000
A2 2001 A2 2001
IEC 60947-5-1 1997 Part 5-1: Control circuit devices and EN 60947-5-1 1997
switching elements - Electromechanical + A12 1999
control circuit devices
A1 1999 A1 1999
A2 1999 A2 2000
1)
IEC 61131-2 1992 Programmable controllers EN 61131-2 1994
Part 2: Equipment requirements and
tests
1)
EN 61131-2:1994 is superseded by EN 61131-2:2003 + corrigendum August 2003, which is based on
IEC 61131-2:2003.
NORME CEI
INTERNATIONALE IEC
60947-5-4
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2002-10
Appareillage à basse tension –
Partie 5-4:
Appareils et éléments de commutation
pour circuits de commande –
Méthode d'évaluation des performances
des contacts à basse énergie –
Essais spéciaux
Low-voltage switchgear and controlgear –
Part 5-4:
Control circuit devices and switching elements –
Method of assessing the performance of
low-energy contacts – Special tests
IEC 2002 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
T
Commission Electrotechnique Internationale PRICE CODE
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
60947-5-4 IEC:2002 – 3 –
CONTENTS
FOREWORD . 5
INTRODUCTION .9
1 Scope and object .11
2 Normative references.11
3 Definitions and list of symbols used .13
3.1 Definitions .13
3.2 List of symbols used .17
4 General principles.19
5 General test method .21
6 General characteristics .23
6.1 Measurement methods .23
6.2 Sequences of operations .25
6.3 Electrical characteristics .29
6.4 Characteristics of operation .31
7 Characterization of defects .33
7.1 Basic method.33
7.2 Monitoring the load (figure 3).33
8 Ambient conditions .33
8.1 Normal conditions.33
8.2 Preconditioning.35
8.3 Particular conditions .35
9 Methods of reporting.35
9.1 Failure criterion .35
9.2 Reporting the failure rate .35
10 Information to be provided in the test report.39
Annex A (normative) Information to be supplied by the manufacturer .43
Bibliography.49
Figure 1 – Functional diagram of the testing equipment.21
Figure 2 – Typical test circuit for the basic method.23
Figure 3 – Test circuit for monitoring a load .25
Figure 4 – Sequential diagram with load-switching contacts .27
Figure 5 – Sequential diagram without load-switching contacts .29
Table 1 – Coefficient K for a time-terminated test .41
c
60947-5-4 IEC:2002 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
Part 5-4: Control circuit devices and switching elements –
Method of assessing the performance of low-energy contacts –
Special tests
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60947-5-4 has been prepared by subcommittee 17B: Low-voltage
switchgear and controlgear, of IEC technical committee 17: Switchgear and controlgear.
This second edition cancels and replaces the first edition which was issued as a technical
report in 1996. It now has the status of an International Standard.
The text of this standard is based on the following documents:
FDIS Report on voting
17B/1228/FDIS 17B/1254/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
Some slight modifications, mainly of an editorial nature, have been introduced since the first
edition.
60947-5-4 IEC:2002 – 7 –
The committee has decided that the contents of this publication will remain unchanged until
2006. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
60947-5-4 IEC:2002 – 9 –
INTRODUCTION
Control switches may not be suitable for use at very low voltages and therefore it is
recommended to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.