EN 60728-1-1:2010

Cable networks for television signals, sound signals and interactive services - Part 1-1: RF cabling for two way home networks

IEC 60728-1-1:2010(E) provides the requirements and describes the implementation guidelines of RF cabling for two-way home networks; it is applicable to any home network that distributes signals provided by CATV/MATV/SMATV cable networks (including individual receiving systems) having a coaxial cable output. It is also applicable to home networks where some part of the distribution network uses wireless links, for example in place of the receiver cord. It is therefore applicable to RF cabling for two-way home networks with wired cords or wireless links inside a room and primarily intended for television and sound signals operating between about 5 MHz and 3 000 MHz. The frequency range is extended to 6 000 MHz for distribution techniques that replace wired cords with a wireless two-way communication inside a room (or a small number of adjacent rooms) that uses the 5 GHz to 6 GHz band.

Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste - Teil 1-1: Zweiwege-HF-Wohnungsvernetzung

Réseaux de distribution par câbles destinés aux signaux de télévision, de radiodiffusion sonore et aux services interactifs - Partie 1-1 : câblage RF pour réseaux domestiques bidirectionnels

Kabelska omrežja za televizijske in zvokovne signale ter interaktivne storitve - 1-1. del: RF okablenje za dvosmerna domača omrežja (IEC 60728-1-1:2010)

Ta del IEC 60728 določa zahteve in opisuje smernice za implementacijo RF okablenja za dvosmerna domača omrežja; velja za katero koli domače omrežje, ki distribuira signale, katere posredujejo CATV/MATV/SMATV kabelska omrežja (vključno s posamičnimi sistemi za sprejem), ki imajo koaksialni kabelski izhod. Prav tako velja za domača omrežja, pri katerih nek del distribucijskega omrežja uporablja brezžične povezave, na primer na mestu sprejemnega kabla. Ta del IEC 60728 se potemtakem uporablja za RF okablenje za dvosmerna domača omrežja z žičnimi kabli ali brezžičnimi povezavami znotraj sobe ter je namenjen predvsem za televizijo in zvočne signale, ki delujejo med približno 5 MHz in 3000 MHz. Frekvenčni razpon se poveča na 6000 MHz pri distribucijskih tehnikah, ki nadomeščajo žične kable z brezžično dvosmerno komunikacijo znotraj sobe (ali manjšega števila sosednjih sob), ki uporablja pas med od 5 GHz do 6 GHz. V stavbi, razdeljeni v stanovanjske bloke, se distribucija signala znotraj doma začne od domačega omrežnega vmesnika (HNI) do sistemskega izhoda ali vhodnega terminala. Zahteve pri sistemskem izhodu so podane v IEC 60728-1, klavzuli 5 in zahteve pri HNI so podane v IEC 60728-1, klavzuli 7. V klavzuli 5 tega standarda so podane dodatne zahteve. Ta standard obravnava različne možnosti za distribuiranje signalov v domačem omrežju z uporabo koaksialnih kablov, simetričnih parnih kablov, kablov iz optičnih vlaken (steklenih ali plastičnih) in tudi brezžičnih povezav znotraj sobe (ali manjšega števila sosednjih sob) za nadomeščanje žičnih kablov. Ta standard se sklicuje na osnovne metode merjenja operativnih značilnosti domačega kabelskega omrežja z namenom oceniti njegovo delovanje.  Vse zahteve se nanašajo na omejitve delovanja, dosežene med vhodi pri domačem omrežnem vmesniku (HNI) in izhodom preko katerega koli izstopa iz sistema, kadar  je prekinjen z uporom, enakim nazivni obremenitvi impedance sistema, razen če je drugače opredeljeno. Kadar se izhodi iz sistema ne uporabljajo, zgoraj navedeno velja za vhodni terminal.  Klavzula 5 opredeljuje omejitve delovanja, ki se merijo pri sistemskem izhodu ali vhodnem terminalu za neoslabljen (idealni) preskusni signal, ki se uporablja pri HNI. Pod običajnimi operativnimi pogoji za kateri koli analogni kanal in kadar so te omejitve dosežene, bo kumulativni učinek neoslabljenosti katerega koli posameznega parametra pri HNI ter tisti, ki je posledica domačega omrežja, proizvedel slikovne in zvočne signale, ki niso slabši od stopnje štiri na petstopenjski lestvici oslabljenosti, navedene v ITU-R BT.500. Te zahteve so podane v IEC 60728-1-2. Za digitalno modulirane signale je ta zahteva glede kakovosti QEF (kvazi brez napak) sprejem. Ta standard opisuje fizično plast povezave za domača omrežja. Opis protokolov, ki se zahteva za plast 2 in višje plasti, je zunaj področja uporabe tega standarda. Logične povezave med napravami v okviru domačega omrežja potemtakem niso vedno zagotovljene.

General Information

• Status: Withdrawn
• Publication Date: 22-Apr-2010
• Withdrawal Date: 31-Mar-2013
• ICS: 33.060.30 - Radio relay and fixed satellite communications systems
• ICS: 33.160.01 - Audio, video and audiovisual systems in general
• Technical Committee: CLC/TC 209 - Cable networks for television signals, sound signals and interactive services
• Drafting Committee: IEC/TC 100 - IEC_TC_100
• Parallel Committee: IEC/TC 100 - IEC_TC_100
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 11-Apr-2017
• Completion Date: 11-Apr-2017
• Ref Project: SIST EN 60728-1-1:2010 - Cable networks for television signals, sound signals and interactive services - Part 1-1: RF cabling for two way home networks (IEC 60728-1-1:2010)

Relations

• Replaced By: CWA 45546-1:2004 - Guidelines to standardisers of Collective Transport Systems - Needs of older people and persons with disabilities - Part 1: Basic Guidelines
• Effective Date: 29-Oct-2012

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2010
.DEHOVNDRPUHåMD]DWHOHYL]LMVNHLQ]YRNRYQHVLJQDOHWHULQWHUDNWLYQHVWRULWYH
GHO5)RNDEOHQMH]DGYRVPHUQDGRPDþDRPUHåMD,(&
Cable networks for television signals, sound signals and interactive services - Part 1-1:
RF cabling for two way home networks (IEC 60728-1-1:2010)
Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste - Teil 1-1: Zweiwege-
HFWohnungsvernetzung (IEC 60728-1-1:2010)
5pVHDX[GHGLVWULEXWLRQSDUFkEOHVGHVWLQpVDX[VLJQDX[GHWpOpYLVLRQGHUDGLRGLIIXVLRQ
VRQRUHHWDX[VHUYLFHVLQWHUDFWLIV3DUWLHFkEODJH5)SRXUUpVHDX[
GRPHVWLTXHVELGLUHFWLRQQHOV&(,
Ta slovenski standard je istoveten z: EN 60728-1-1:2010
ICS:
33.060.40 Kabelski razdelilni sistemi Cabled distribution systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60728-1-1
NORME EUROPÉENNE
April 2010
EUROPÄISCHE NORM
ICS 33.060.30; 33.160.01
English version
Cable networks for television signals, sound signals
and interactive services -
Part 1-1: RF cabling for two way home networks
(IEC 60728-1-1:2010)
Réseaux de distribution par câbles Kabelnetze für Fernsehsignale,
destinés aux signaux de télévision, Tonsignale und interaktive Dienste -
de radiodiffusion sonore et aux services Teil 1-1: Zweiwege-HF-
interactifs - Wohnungsvernetzung
Partie 1-1 : câblage RF pour réseaux (IEC 60728-1-1:2010)
domestiques bidirectionnels
(CEI 60728-1-1:2010)
This European Standard was approved by CENELEC on 2010-04-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60728-1-1:2010 E
Foreword
The text of document 100/1622/FDIS, future edition 1 of IEC 60728-1-1, prepared by IEC TC 100, Audio,
video and multimedia systems and equipment, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 60728-1-1 on 2010-04-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2011-01-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-04-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60728-1-1:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61169-2 NOTE  Harmonized as EN 61169-2.
IEC 61169-24 NOTE  Harmonized as EN 61169-24.
IEC 61196-2 NOTE  Harmonized as EN 61196-2.
__________
- 3 - EN 60728-1-1:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

- - Coaxial cables - EN 50117-2-4 -
Part 2-4: Sectional specification for cables
used in cabled distribution networks - Indoor
drop cables for systems operating at
5 MHz - 3 000 MHz
IEC 60050-705 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 705: Radio wave propagation

IEC 60050-712 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 712: Antennas
IEC 60050-725 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 725: Space radiocommunications

IEC 60617 - Standard data element types with - -
associated classification scheme for
electric components -
Part 4: IEC reference collection of standard
data element types and component classes

IEC 60728-1 2007 Cable networks for television signals, sound EN 60728-1 2008
signals and interactive services -
Part 1: System performance of forward paths

IEC 60728-1-2 - Cable networks for television signals, sound EN 60728-1-2 -
signals and interactive services -
Part 1-2: Performance requirements for
signals delivered at the system outlet in
operation
IEC 60728-3 2005 Cable networks for television signals, sound EN 60728-3 2006
signals and interactive services -
Part 3: Active wideband equipment for coaxial
cable networks
IEC 60728-10 - Cable networks for television signals, sound EN 60728-10 -
signals and interactive services -
Part 10: System performance of return paths

IEC 60966 Series Radio frequency and coaxial cable EN 60966 Series
assemblies
IEC 60966-2-4 - Radio frequency and coaxial cable EN 60966-2-4 -
assemblies -
Part 2-4: Detail specification for cable
assemblies for radio and TV receivers -
Frequency range 0 MHz to 3 000 MHz,
IEC 61169-2 connectors
Publication Year Title EN/HD Year

IEC 60966-2-5 - Radio frequency and coaxial cable EN 60966-2-5 -
assemblies -
Part 2-5: Detail specification for cable
assemblies for radio and TV receivers -
Frequency range 0 MHz to 1 000 MHz,
IEC 61169-2 connectors
IEC 60966-2-6 - Radio frequency and coaxial cable EN 60966-2-6 -
assemblies -
Part 2-6: Detail specification for cable
assemblies for radio and TV receivers -
Frequency range 0 MHz to 3 000 MHz,
IEC 61169-24 connectors
ETSI EN 300 421 - Digital Video Broadcasting (DVB): Framing - -
structure, channel coding and modulation for
11/12 GHz satellite services
ETSI EN 300 429 - Digital Video Broadcasting (DVB): Framing - -
structure, channel coding and modulation for
cable systems
ETSI EN 300 473 - Digital Video Broadcasting (DVB): Satellite - -
Master Antenna Television (SMATV)
distribution systems
ETSI EN 300 744 - Digital Video Broadcasting (DVB): Framing - -
structure, channel coding and modulation for
digital terrestrial television

ETSI EN 302 307 - Digital Video Broadcasting (DVB);Second - -
generation framing structure, channel coding
and modulation systems for Broadcasting,
Interactive Services, News Gathering and
other broadband satellite applications

IEEE 802.11 1999 IEEE Standard for Information technology-- -
Telecommunications and information
exchange between systems-Local and
metropolitan area networks-Specific
requirements -
Part 11: Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY)
Specifications
IEEE 802.11a 1999 IEEE Standard for Information technology – - -
Telecommunications and information
exchange between systems – Local and
metropolitan area networks – Specific
requirements –
Part 11: Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY)
specifications
IEEE 802.11b 1999 Supplement to 802.11-1999, Wireless LAN - -
MAC and PHY specifications: Higher speed
Physical Layer (PHY) extension in the
2.4 GHz band
- 5 - EN 60728-1-1:2010
Publication Year Title EN/HD Year

IEEE 802.11e 2005 IEEE Standard for Information technology – - -
Telecommunications and information
exchange between systems – Local and
metropolitan area networks – Specific
requirements
Part 11: Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY)
specifications
IEEE 802.11g 2003 IEEE Standard for Information technology – - -
Telecommunications and information
exchange between systems – Local and
metropolitan area networks – Specific
requirements –
Part 11: Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY)
specifications
IEEE 802.11h 2003 IEEE Standard for Information technology – - -
Telecommunications and Information
Exchange Between Systems – LAN/MAN
Specific Requirements –
Part 11: Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY)
Specifications: Spectrum and Transmit Power
Management Extensions in the 5GHz band in
Europe
IEEE 802.11n/D4.0 - March 2008 Active Unapproved Draft – IEEE - -
Draft STANDARD for Information Technology-
Telecommunications and information
exchange between systems- Local and
metropolitan area networks-Specific
requirements-
Part 11: Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY)
specifications
IEEE 802.16 2004 IEEE Standard for Local and metropolitan - -
area networks –
Part 16: Air Interface for Fixed Broadband
Wireless Access Systems (WiMax)

ITU-R - Methodology for the subjective assessment of - -
Recommendation the quality of television pictures
BT.500
ITU-T - Transmission performance of television - -
Recommendation circuits designed for use in international
J.61 connections
ITU-T - Insertion of test signals in the field-blanking - -
Recommendation interval of monochrome and colour television
J.63 signals
IEC 60728-1-1 ®
Edition 1.0 2010-01
INTERNATIONAL
STANDARD
colour
inside
Cable networks for television signals, sound signals and interactive services –
Part 1-1: RF cabling for two way home networks

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
XA
ICS 33.060.30; 33.160.01 ISBN 2-8318-1074-3
– 2 – 60728-1-1 © IEC:2010(E)
CONTENTS
FOREWORD.0H5
INTRODUCTION.1H7
1 Scope.2H9
2 Normative references .3H10
3 Terms, definitions, symbols and abbreviations.4H12
3.1 Terms and definitions .5H12
3.2 Symbols .6H18
3.3 Abbreviations .7H19
4 Methods of measurement for the home network.8H20
5 Performance requirements of the home network .9H21
5.1 General .10H21
5.2 Impedance .11H22
5.3 Performance requirements at the terminal input .12H22
5.3.1 General .13H22
5.3.2 Signal level.14H22
5.3.3 Other parameters .15H22
5.4 Performance requirements at system outlets .16H23
5.4.1 Minimum and maximum carrier levels .17H23
5.4.2 Mutual isolation between system outlets .18H23
5.4.3 Isolation between individual outlets in one household .19H23
5.4.4 Isolation between forward and return path .20H23
5.4.5 Long-term frequency stability of distributed carrier signals at any
system outlet .21H23
5.5 Performance requirements at the HNI.22H23
5.5.1 Minimum and maximum carrier levels at HNI1 .23H23
5.5.2 Minimum and maximum carrier levels at HNI2 and HNI3.24H23
5.6 Carrier level differences in the home network from HNI to system outlet.25H23
5.7 F
...