EN 61915-2:2012

Low-voltage switchgear and controlgear - Device profiles for networked industrial devices - Part 2: Root device profiles for starters and similar equipment

IEC 61915-2:2011 specifies root device profiles as defined by IEC 61915-1 for starters and similar equipment covered by the following product standards: - electromechanical contactors and motor-starters (IEC 60947-4-1), - AC semiconductor motor controllers and starters (IEC 60947-4-2), - AC semiconductor controllers and contactors for non-motor loads (IEC 60947-4-3), - control and protective switching devices (or equipment) (CPS) (IEC 60947-6-2), - control units for built-in thermal protection (PTC) for rotating electrical machines (IEC 60947-8).

Niederspannungsschaltgeräte - Geräteprofile für vernetzte industrielle Schaltgeräte - Teil 2: Grundlegende Geräteprofile für Starter und ähnliche Betriebsmittel

Appareillage à basse tension - Profils d'appareil pour les appareils industriels mis en réseau - Partie 2: Profils racines d'appareil pour les démarreurs et les matériels similaires

La CEI 61915-2:2011 spécifie les profils racines d'appareil, tels que définis par la CEI 61915-1, pour les démarreurs et les matériels similaires couverts par les normes de produit suivantes: - contacteurs et démarreurs de moteurs électromécaniques (CEI 60947-4-1), - gradateurs et démarreurs de moteurs à semi-conducteurs à courant alternatif (CEI 60947-4-2), - gradateurs et contacteurs à semi-conducteurs pour charges, autres que des moteurs, à courant alternatif (CEI 60947-4-3), - appareils (ou matériel) de connexion de commande et de protection (ACP) (CEI 60947-6-2), - unités de commande pour la protection thermique incorporée (CTP) aux machines électriques tournantes (CEI 60947-8).

Nizkonapetostne stikalne in krmilne naprave - Profili naprav za industrijske naprave, vključene v omrežje - 2. del: Korenski profili naprav za starterje in podobno opremo (IEC 61915-2:2011)

Ta del standarda IEC 61915 določa korenske profile naprav iz standarda IEC 61915-1 za starterje in podobno opremo, zajeto v naslednjih standardih za izdelek: – elektromehanski kontaktorji in motorski zaganjalniki (IEC 60947-4-1), – polprevodniški krmilniki in zaganjalniki motorjev na izmenični tok (IEC 60947-4-2), – polprevodniški krmilniki in kontaktorji na izmenični tok za nemotorske obremenitve (IEC 60947-4-3), – krmilne in zaščitne stikalne naprave (ali oprema) (CPS) (IEC 60947-6-2), – krmilne enote za vgrajeno toplotno zaščito (PTC) rotacijskih električnih strojev (IEC 60947-8).

General Information

• Status: Published
• Publication Date: 08-Mar-2012
• Withdrawal Date: 23-Nov-2014
• ICS: 29.130 - Switchgear and controlgear
• Technical Committee: CLC/TC 121A - Low-voltage switchgear and controlgear
• Drafting Committee: IEC/SC 121A - Low-voltage switchgear and controlgear
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 09-Mar-2012
• Completion Date: 09-Mar-2012
• Ref Project: SIST EN 61915-2:2012 - Low-voltage switchgear and controlgear - Device profiles for networked industrial devices - Part 2: Root device profiles for starters and similar equipment (IEC 61915-2:2011)

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2012
1L]NRQDSHWRVWQHVWLNDOQHLQNUPLOQHQDSUDYH3URILOLQDSUDY]DLQGXVWULMVNH
QDSUDYHYNOMXþHQHYRPUHåMHGHO.RUHQVNLSURILOLQDSUDY]DVWDUWHUMHLQ
SRGREQRRSUHPR,(&
Low-voltage switchgear and controlgear - Device profiles for networked industrial devices
- Part 2: Root device profiles for starters and similar equipment (IEC 61915-2:2011)
Niederspannungsschaltgeräte - Geräteprofile für vernetzte industrielle Schaltgeräte - Teil
2: Grundlegende Geräteprofile für Starter und ähnliche Betriebsmittel (IEC 61915-
2:2011)
Appareillage à basse tension - Profils d'appareil pour les appareils industriels mis en
réseau - Partie 2: Profils racine pour les démarreurs et les équipements similaires (CEI
61915-2:2011)
Ta slovenski standard je istoveten z: EN 61915-2:2012
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61915-2
NORME EUROPÉENNE
March 2012
EUROPÄISCHE NORM
ICS 29.130
English version
Low-voltage switchgear and controlgear -
Device profiles for networked industrial devices -
Part 2: Root device profiles for starters and similar equipment
(IEC 61915-2:2011)
Appareillage à basse tension -  Niederspannungsschaltgeräte -
Profils d'appareil pour les appareils Geräteprofile für vernetzte industrielle
industriels mis en réseau - Schaltgeräte -
Partie 2: Profils racines d'appareil pour les Teil 2: Grundlegende Geräteprofile für
démarreurs et les matériels similaires Starter und ähnliche Betriebsmittel
(CEI 61915-2:2011) (IEC 61915-2:2011)

This European Standard was approved by CENELEC on 2011-11-24. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61915-2:2012 E
Foreword
The text of document 17B/1752/FDIS, future edition 1 of IEC 61915-2, prepared by SC 17B, "Low-voltage
switchgear and controlgear", of IEC/TC 17, "Switchgear and controlgear" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61915-2:2012.

The following dates are fixed:
(dop) 2012-08-24
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-11-24
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61915-2:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60947 series NOTE  Harmonized in EN 60947 series.
IEC 60947-4-1:2009 NOTE  Harmonized as EN 60947-4-1:2010 (not modified).
1)
IEC 60947-4-2:2011 NOTE  Harmonized as EN 60947-4-2:201X (not modified).
IEC 60947-4-3:1999 NOTE  Harmonized as EN 60947-4-3:2000 + A1:2006 + A2:2011 (not modified).
+ A1:2006
+ A2:2011
IEC 60947-6-2:2002 NOTE  Harmonized as EN 60947-6-2:2003 + A1:2007 (not modified).
+ A1:2007
1)
IEC 60947-8:2003 NOTE  Harmonized as EN 60947-8:2003 + A1:2006 + A2:201X (not modified).
+ A1:2006
+ A2:2011
1)
To be published.
- 3 - EN 61915-2:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60947-1 2007 Low-voltage switchgear and controlgear - EN 60947-1 2007
+ A1 2010 Part 1: General rules + A1 2011

IEC 61915-1 2007 Low-voltage switchgear and controlgear - EN 61915-1 2008
Device profiles for networked industrial
devices -
Part 1: General rules for the development of
device profiles
IEC 61915-2 ®
Edition 1.0 2011-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Low-voltage switchgear and controlgear – Device profiles for networked
industrial devices –
Part 2: Root device profiles for starters and similar equipment

Appareillage à basse tension – Profils d'appareil pour les appareils industriels
mis en réseau –
Partie 2: Profils racines d'appareil pour les démarreurs et les matériels similaires

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX W
ICS 29.130.20 ISBN 978-2-88912-763-4

– 2 – 61915-2 © IEC:2011
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 General . 6
3.2 Terms and definitions . 6
3.3 Abbreviated terms . 9
4 Root device profiles . 9
5 Common elements of the root device profile . 11
5.1 R parameters . 11
5.2 RW parameters . 17
5.3 Parameter groups . 20
5.4 State model . 22
5.4.1 Motor starter . 22
5.4.2 Soft starter . 24
5.4.3 Motor management starter . 24
6 Root device profiles . 27
6.1 Assemblies supported . 27
6.2 Motor starter . 28
6.3 Soft starter . 31
6.4 Motor management starter . 33
7 Tests . 35
Bibliography . 36

Figure 1 – State chart diagram of motor starter . 22
Figure 2 – State chart diagram of motor management starter . 24

Table 1 – List of root device profiles . 9
Table 2 – R parameters . 11
Table 3 – RW parameters . 17
Table 4 – Parameters groups . 20
Table 5 – State transition table of motor starter . 23
Table 6 – State transition table of motor management starter . 25
Table 7 – P(IEC 61915-2)00001 . 28
Table 8 – P(IEC 61915-2)00002 . 31
Table 9 – P(IEC 61915-2)00003 . 33

61915-2 © IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
DEVICE PROFILES FOR NETWORKED INDUSTRIAL DEVICES –

Part 2: Root device profiles for starters and similar equipment

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
Int
...