Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic stress tests - Test 6a: Acceleration, steady state

Defines a standard test method to assess the ability of components (essentially connectors) to withstand specified severities of acceleration.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 6-1: Prüfungen mit dynamisch-mechanischer Beanspruchung - Prüfung 6a: Gleichförmiges Beschleunigen, zentrifugal

Connecteurs pour équipements électroniques - Essais et mesures - Partie 6-1: Essais de contraintes dynamiques - Essai 6a: Accélération constante

Etablit une méthode d'essai normalisée pour évaluer l'aptitude d'un composant (essentiellement un connecteur) à supporter des sévérités spécifiées d'accélération.

Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic stress tests - Test 6a: Acceleration, steady state (IEC 60512-6-1:2002)

General Information

Status
Published
Publication Date
18-Apr-2002
Technical Committee
Drafting Committee
Parallel Committee
Current Stage
6060 - Document made available
Start Date
19-Apr-2002
Completion Date
19-Apr-2002

Buy Standard

Standard
EN 60512-6-1:2003
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI SIST EN 60512-6-1:2003
STANDARD
oktober 2003
Connectors for electronic equipment - Tests and measurements - Part 6-1: Dynamic
stress tests - Test 6a: Acceleration, steady state (IEC 60512-6-1:2002)
ICS 31.220.10 Referenčna številka
SIST EN 60512-6-1:2003(en)

© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 60512-6-1
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2002
ICS 31.220.10
English version
Connectors for electronic equipment -
Tests and measurements
Part 6-1: Dynamic stress tests -
Test 6a: Acceleration, steady state
(IEC 60512-6-1:2002)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Essais et mesures Mess- und Prüfverfahren
Partie 6-1: Essais de contraintes Teil 6-1: Prüfungen mit dynamisch-
dynamiques - mechanischer Beanspruchung -
Essai 6a: Accélération constante Prüfung 6a: Gleichförmiges
(CEI 60512-6-1:2002) Beschleunigen, zentrifugal
(IEC 60512-6-1:2002)

This European Standard was approved by CENELEC on 2002-04-01. CENELEC members are bound to

comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and

notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,

Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,

Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60512-6-1:2002 E
---------------------- Page: 2 ----------------------
EN 60512-6-1:2002 - 2 -
Foreword

The text of document 48B/1138/FDIS, future edition 1 of IEC 60512-6-1, prepared by SC 48B,

Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic

equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as

EN 60512-6-1 on 2002-04-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2003-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2005-04-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice

The text of the International Standard IEC 60512-6-1:2002 was approved by CENELEC as a

European Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 60512-6-1:2002
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

This European Standard incorporates by dated or undated reference, provisions from other

publications. These normative references are cited at the appropriate places in the text and the

publications are listed hereafter. For dated references, subsequent amendments to or revisions of any

of these publications apply to this European Standard only when incorporated in it by amendment or

revision. For undated references the latest edition of the publication referred to applies (including

amendments).

NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068-2-7 1983 Basic environmental testing procedures
Part 2: Tests - Test Ga and guidance:
Acceleration, steady state
+ A1 1986 EN 60068-2-7 1993
1) 2)
IEC 60512-1-1 - Connectors for electronic equipment - EN 60512-1-1 2002
Tests and measurements
Part 1-1: General examination -
Test 1a: Visual examination
1) 2)
IEC 60512-2-1 - Part 2-1: Electrical continuity and EN 60512-2-1 2002
contact resistance tests -
Test 2a: Contact resistance - Millivolt
level method
IEC 60512-2-5 - Part 2-5: Electrical continuity and --
contact resistance tests -
Test 2e: Contact disturbance
IEC 60512-7 1993 Electromechanical components for--
electronic equipment - Basic testing
procedures and measuring methods
Part 7: Mechanical operating tests and
sealing tests
Undated reference.
Valid edition at date of issue.
In preparation.
---------------------- Page: 4 ----------------------
NORME CEI
INTERNATIONALE IEC
60512-6-1
INTERNATIONAL
Première édition
STANDARD
First edition
2002-02
Connecteurs pour équipements électroniques –
Essais et mesures –
Partie 6-1:
Essais de contraintes dynamiques –
Essai 6a: Accélération constante
Connectors for electronic equipment –
Tests and measurements –
Part 6-1:
Dynamic stress tests –
Test 6a: Acceleration, steady state
 IEC 2002 Droits de reproduction réservés  Copyright - all rights reserved

Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any

utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including

électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from

microfilms, sans l'accord écrit de l'éditeur. the publisher.

International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland

Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch

CODE PRIX
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 5 ----------------------
60512-6-1  IEC:2002 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 6-1: Dynamic stress tests –
Test 6a: Acceleration, steady state
FOREWORD

1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, the IEC publishes International Standards. Their preparation is

entrusted to technical committees; any IEC National Committee interested in the subject dealt with may

participate in this preparatory work. International, gove
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.