Connectors for electrical and electronic equipment - Part 5: Detail specification for 2-way M8 and M12 circular connectors, shielded or unshielded, free and fixed - Mechanical mating information, pin assignment and additional requirements for Type 5

This part of IEC 63171 describes shielded or unshielded circular connectors with 2 ways and M8 or M12 Styles, typically used for data transmission up to 600 MHz and with current carrying capacity up to 4 A, for use in areas with harsh environmental conditions. These connectors consist of fixed and free connectors either rewirable or non-rewirable. Male connectors have square cross- section contacts, for data and power transmission. M12 describes the dimensions of the styles and thread of the screw-locking mechanism according IEC 61076-2-101 of this size of circular connectors. M8 describes the dimensions of the styles and thread of the screw-locking mechanism according IEC 61076-2-104. The use of alternative locking mechanisms according to IEC 61076-2-010 or IEC 61076-2-011 are possible. The coding provided by this standard prevents the mating of accordingly coded male or female connectors to other similarly sized interfaces covered by this or other standards. These Type 5 connectors are interoperable with Type 2 connectors according IEC 63171-2, except the locking and sealing system provided by the outer shell. The shielded and unshielded connectors are interoperable for their internal transmission performance and can be exchanged. The shielded version has improved EMC and coupling properties. This part of IEC 63171 covers Type 5 connectors. Each part of this series has the associated type number equal to the number of the part in the series. All connectors in the IEC 63171 series are deemed to provide the same functions as defined in IEC 63171:2021, using different mechanical interfaces.

Steckverbinder für elektrische und elektronische Einrichtungen - Teil 5: Einzelspezifikation für 2-polige M8- und M12-Rundsteckverbinder, geschirmt oder ungeschirmt, frei und fest - Mechanische Informationen zum Stecken, Kontaktbelegung und zusätzliche Anforderungen für Typ 5

Connecteurs pour équipements électriques et électroniques - Partie 5: Spécification particulière pour les connecteurs circulaires M8 et M12 à 2 pôles, à fiches et embases écrantées ou non écrantées - Informations d’accouplement mécanique, affectation des broches et exigences supplémentaires pour le type 5

L'IEC 63171-5:2022 fait référence aux Normes internationales pour les essais et les mesures, les essais environnementaux ainsi que les connexions sans soudure. Cette partie de l'IEC 63171 décrit les connecteurs circulaires blindés ou non blindés à 2 voies avec verrouillage IP65/IP67 M8 ou M12, généralement utilisés pour la transmission de données équilibrée à une seule paire avec des fréquences allant jusqu’à 600 MHz et avec une capacité de charge de courant allant jusqu’à 4 A, pour une utilisation dans des zones où les conditions environnementales sont difficiles. Ces connecteurs sont constitués de connecteurs fixes et libres, réengrenables ou non réenfrables. Les connecteurs mâles ont des contacts de section transversale carrée.

Konektorji za električno in elektronsko opremo - 5. del: Podrobna specifikacija za 2-redne okrogle konektorje M8 in M12, zaslonjene ali nezaslonjene, proste ali pritrjene - Informacije o mehanskih prilagoditvah, funkcije polov in dodatne zahteve za tip 5 (IEC 63171-5:2022)

General Information

Status
Published
Publication Date
20-Oct-2022
Technical Committee
Drafting Committee
Current Stage
6060 - Document made available - Publishing
Start Date
21-Oct-2022
Completion Date
21-Oct-2022

Buy Standard

Standard
EN IEC 63171-5:2022
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN IEC 63171-5:2021
English language
30 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 63171-5:2022
01-december-2022
Konektorji za električno in elektronsko opremo - 5. del: Podrobna specifikacija za
2-redne okrogle konektorje M8 in M12, zaslonjene ali nezaslonjene, proste ali
pritrjene - Informacije o mehanskih prilagoditvah, funkcije polov in dodatne
zahteve za tip 5 (IEC 63171-5:2022)
Connectors for electrical and electronic equipment - Part 5: Detail specification for 2-way
M8 and M12 circular connectors, shielded or unshielded, free and fixed - Mechanical
mating information, pin assignment and additional requirements for Type 5 (IEC 63171-
5:2022)
Steckverbinder für elektrische und elektronische Einrichtungen - Produktanforderungen -
Teil 5: Bauartspezifikation für geschirmte oder ungeschirmte, freie und feste
Rundsteckverbinder mit bis zu 8 Polen: Informationen zur mechanischen Passung,
Kontaktstiftbelegung und zusätzliche Anforderungen für Typ 5 (IEC 63171-5:2022)
Connecteurs pour équipements électriques et électroniques – Partie 5: Spécification
particulière pour les connecteurs circulaires M8 et M12 à 2 pôles, à fiches et embases
écrantées ou non écrantées: informations d’accouplement mécanique, affectation des
broches et exigences supplémentaires pour le type 5 (IEC 63171-5:2022)
Ta slovenski standard je istoveten z: EN IEC 63171-5:2022
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
SIST EN IEC 63171-5:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 63171-5:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 63171-5:2022


EUROPEAN STANDARD EN IEC 63171-5

NORME EUROPÉENNE

EUROPÄISCHE NORM October 2022
ICS 31.220.10

English Version
Connectors for electrical and electronic equipment - Part 5:
Detail specification for 2-way M8 and M12 circular connectors,
shielded or unshielded, free and fixed - Mechanical mating
information, pin assignment and additional requirements for
Type 5
(IEC 63171-5:2022)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektrische und elektronische
- Partie 5: Spécification particulière pour les connecteurs Einrichtungen - Produktanforderungen - Teil 5:
circulaires M8 et M12 à 2 pôles, à fiches et embases Bauartspezifikation für geschirmte oder ungeschirmte, freie
écrantées ou non écrantées - Informations d'accouplement und feste Rundsteckverbinder mit bis zu 8 Polen -
mécanique, affectation des broches et exigences Informationen zur mechanischen Passung,
supplémentaires pour le type 5 Kontaktstiftbelegung und zusätzliche Anforderungen für
(IEC 63171-5:2022) Typ 5
(IEC 63171-5:2022)
This European Standard was approved by CENELEC on 2022-10-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 63171-5:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 63171-5:2022
EN IEC 63171-5:2022 (E)
European foreword
The text of document 48B/2973/FDIS, future edition 1 of IEC 63171-5, prepared by SC 48B "Electrical
connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical and electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 63171-5:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-07-20
level by publication of an identical national standard or by endorsement
• latest date by which the nationa
...

SLOVENSKI STANDARD
oSIST prEN IEC 63171-5:2021
01-december-2021
Konektorji za električno in elektronsko opremo - 5. del: Podrobna specifikacija za
2-redne okrogle konektorje M8 in M12, zaslonjene ali nezaslonjene, proste ali
pritrjene - Informacije o mehanskih prilagoditvah, funkcije polov in dodatne
zahteve za tip 5
Connectors for electrical and electronic equipment - Part 5: Detail specification for 2-way
M8 and M12 circular connectors, shielded or unshielded, free and fixed - Mechanical
mating information, pin assignment and additional requirements for Type 5
Ta slovenski standard je istoveten z: prEN IEC 63171-5:2021
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
oSIST prEN IEC 63171-5:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 63171-5:2021

---------------------- Page: 2 ----------------------
oSIST prEN IEC 63171-5:2021
48B/2912/CDV

COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 63171-5 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2021-10-15 2022-01-07
SUPERSEDES DOCUMENTS:
48B/2809/CDV, 48B/2905/RVC

IEC SC 48B : ELECTRICAL CONNECTORS
SECRETARIAT: SECRETARY:
United States of America Mr Jeffrey Toran
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:

SC 65C,ISO/IEC JTC 1/SC 25
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING


This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.

TITLE:
Connectors for electrical and electronic equipment – Part 5: Detail specification for 2-way M8
and M12 circular connectors, shielded or unshielded, free and fixed – Mechanical mating
information, pin assignment and additional requirements for Type 5

PROPOSED STABILITY DATE: 2024

NOTE FROM TC/SC OFFICERS:
Project title has been changed. Original title: Connectors for electrical and electronic equipment –
Product requirements - Part 5: Detail specification for circular connectors with up to 8 ways, shielded
or unshielded, free and fixed connectors: mechanical mating information, pin assignment and additional
requirements for type 5

Copyright © 2021 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.

---------------------- Page: 3 ----------------------
oSIST prEN IEC 63171-5:2021
IEC CDV 63171-5/Ed1 © IEC 2021 2 48B/2912/CDV

1 CONTENTS
2 FOREWORD. 5
3 INTRODUCTION . 7
4 1 Scope . 9
5 2 Normative references . 9
6 3 Terms and definitions . 10
7 3.1 mounting orientation . 11
8 4 Common features and typical connector pair . 11
9 4.1 Systems of levels . 11
10 Performance levels . 11
11 Compatibility levels, according to IEC 61076-1 . 11
12 4.2 Pin assignment . 11
13 4.3 Codings . 11
14 4.4 Classification into climatic categories . 11
15 4.5 Creepage and clearance distances . 11
16 4.6 Current-carrying capacity .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.