Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type

IEC 62841-2-4:2014 applies to hand-held sanders and polishers with the exception of disc-type tools covered by IEC 62841-2-3. Tools covered by this standard include but are not limited to belt sanders, drum sanders or polishers, reciprocating sanders or polishers, orbital sanders or polishers and random orbit sanders or polishers. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Sander, Polisher, Belt, Drum Orbital, Reciprocating, Random Orbit This publication is to be read in conjunction with IEC 62841-1:2014.

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-4: Besondere Anforderungen für handgeführte Schleifer und Polierer außer Tellerschleifern

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-4: Exigences particulières pour les ponceuses et lustreuses portatives, autres que du type à disque

IEC 62841-2-4:2014 s'applique aux ponceuses et lustreuses portatives, à l'exception des outils du type à disque, couverts par l'IEC 62841-2-3. Les outils couverts par la présente norme incluent, mais ne se limitent pas aux ponceuses à bande, aux ponceuses ou lustreuses à tambour, aux ponceuses ou lustreuses vibrantes, aux ponceuses ou lustreuses orbitales, et aux ponceuses ou aux lustreuses orbitales spéciales. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable. L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 12 mois et au plus tard 36 mois après la date de publication. Mots-clés: Ponceuse, Lustreuse, Bande, Tambour Orbital, Vibrantes, Orbitale spéciale Cette publication doit être lue conjointement avec la CEI 62841-1:2014.

Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-4. del: Posebne zahteve za ročne brusilnike in polirnike, razen diskovnih brusilnikov - Dopolnilo AB

General Information

Status
Not Published
Publication Date
24-May-2026
Current Stage
4060 - Enquiry results established and sent to TC, SR, BTTF - Enquiry
Start Date
03-May-2024
Due Date
19-Feb-2025
Completion Date
03-May-2024

Relations

Buy Standard

Draft
EN 62841-2-4:2014/oprAB:2024
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2024
Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost
- 2-4. del: Posebne zahteve za ročne brusilnike in polirnike, razen diskovnih
brusilnikov - Dopolnilo AB
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and
polishers other than disc type
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen - Sicherheit - Teil 2-4: Besondere Anforderungen für
handgeführte Schleifer und Polierer außer Tellerschleifern
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 2-4: Exigences particulières pour les ponceuses et lustreuses
portatives, autres que du type à disque
Ta slovenski standard je istoveten z: EN 62841-2-4:2014/prAB:2024
ICS:
25.080.50 Brusilni in polirni stroji Grinding and polishing
machines
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD DRAFT
EN 62841-2-4:2014
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAB
February 2024
ICS 25.140.20 -
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-4: Particular
requirements for hand-held sanders and polishers other than
disc type
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-4: Exigences transportable Werkzeuge und Rasen- und
particulières pour les ponceuses et lustreuses portatives, Gartenmaschinen - Sicherheit - Teil 2-4: Besondere
autres que du type à disque Anforderungen für handgeführte Schleifer und Polierer
außer Tellerschleifern
This draft amendment prAB, if approved, will modify the European Standard EN 62841-2-4:2014; it is submitted to CENELEC members for
enquiry.
Deadline for CENELEC: 2024-05-03.

It has been drawn up by CLC/TC 116.

If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

This draft amendment was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 79300 Ref. No. EN 62841-2-4:2014/prAB:2024 E

1 European foreword
2 This document (EN 62841-2-4:2014/prAB:2024) has been prepared by CLC/TC 116 “Safety and
3 environmental aspects of motor-operated electric tools”.
4 This document is currently submitted to the Enquiry.
5 The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 48 months
conflicting with this document have to be (to be confirmed or
withdrawn
modified when voting)
6 This document modifies by common modifications EN 62841-2-4:2014/prA1:2024, which consists of the
7 text of 116/xxx/CDV (future IEC 62841-2-4:2014/A1:202x) prepared by IEC/TC 116 “Safety of motor-
8 operated electric tools”.
9 EN 62841-2-4:2014/prA1:2024 together with prAB:202x revises the requirements for power switches for
10 both sanders and polishers. In addition, it is clarified that subclauses 21.18.1.2 and 23.3 of EN 62841-
11 1:2014 are not applicable for these tools.
12 This document has been prepared under a standardization request addressed to CENELEC by the
13 European Commission. The Standing Committee of the EFTA States subsequently approves these
14 requests for its Member States.
15 For relationship with EU Legislation, see informative Annex ZZ, which is an integral part of this document.
16 1 Modification to Annex K, “Battery tools and battery packs”
17 Add the following new subclause:
18 “K.21.18.Z301  Isolation and disabling device
19 Belt sanders, drum sanders and drum polishers with an integral battery shall be equipped
20 — with an isolation device to prevent the risk of injury from mechanical hazards during servicing or user
21 maintenance; or
22 — with a disabling device that prevents unintentional starting of the tool.
23 An isolation device shall
24 — provide disconnection of at least one pole of the battery from the serviceable region of the tool;
25 — be equipped with an unambiguous indication of the state of the disconnection device which
26 correspond
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.