CLC/TC 116/WG 02 - To carry out comparison to identify any amendments required to ensure that the CLC/TC 61F standards are in agreement with the Machinery Directive

IEC 62841-2-7:2024 deals with the safety of electric motor-operated hand-held spray guns for non-flammable materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-7 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

2021-12-20: This prAA includes common mods to EN IEC 62841-2-7 (PR=75432)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

IEC 62841-2-12:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held concrete vibrators. IEC 62841-1:2014, Clause 1 is applicable, except as follows. Addition: This document applies to hand-held concrete vibrators.

2021-12-20: This prAA includes common mods to EN IEC 62841-2-12 (PR=75428)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

This part of EN 62841 applies to reciprocating saws such as jig saws and sabre saws.

2021-12-14: This prAB includes common mods to EN IEC 62841-2-6:2020/A1 (PR=75447)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

DOW=DOR+48 months is applied to all parts in EN IEC 62841 series
2021-12-14: Common mods to this prA1 are included in prAB (PR=75448)

This part of IEC 62841 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.

2022-04-01- HD: NEXT ACTION: TB ACTION (2nd FV draft sent to production on 2022-03-25)
2020-06-16: Common mods to this prA1 are included in prAC (PR=72183)
DOW=DOR+48 months

2020-12-24: Common mods to this prA1 are included in prAB (PR=73280) for simultaneous circulation
D164/C043: DOW= dor + 48 months

2020-12-14: This prAA represents common mods to EN IEC (PR=73190) for simultaneous circulation
D164/C043: DOW=DOR+48 months

2020-12-24: This prAB represents common mods to EN 62841-3-10:2015/prA1 (PR=73192) under parallel
D164/C043: DOW= dor + 48 months

2020-12-14: Common mods to this EN IEC are included in prAA (PR=73229) for simultaneous circulation
D164/C043: DOW=DOR+48 months

2020-12-14: This prAA represents common mods to EN IEC (PR=71053) for simultaneous circulation
D164/C043: DOW=DOR+48 months

IEC 62841-3-5:2022 applies to band saws intended for cutting wood and analogous materials, plastics and metals, except magnesium. This document does not apply to transportable scroll saws and jig saws with a reciprocating blade. This document does not apply to  
hand-held band saws;
non-vertical saws; and
wire saws.  NOTE 101 It is planned that a document on transportable scroll saws and jig saws will be published. NOTE 102 Hand-held band saws will be covered by a future part of IEC 62841-2. NOTE 103 In Europe (EN IEC 62841-3-5), the following conditions apply: This document does not apply to stationary band saws intended to cut wood and similar materials. Stationary band saws that are intended to cut wood and similar materials are covered by EN 1807-1. This document applies to band saws having a mass of: - maximum 25 kg for tools capable of being lifted by hand by one person; - maximum 50 kg for tools capable of being lifted by hand by two persons.

This standard deals with the safety of electric motor-operated or magnetically driven: - hand-held tools (IEC 62841-2); - transportable tools (IEC 62841-3); - lawn and garden machinery (IEC 62841-4). The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W.

IEC 62841-2-1:2017 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard does not apply to rotary hammers, even if they can be used as a drill. This Part 2-1 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drill, Impact Drill, Hand-held tool, Safety

IEC 62841-2-17:2017 applies to routers intended for cutting slots into or shaping the edge of various materials. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This part of IEC 62841 does not apply to jointers. Routers that are primarily used for trimming the edge of materials are also known as trimmers. Routers that are used to cut various materials through the rotary action are also known as rotary cutters. This Part 2-17 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Router, Trimmer, Hand-held tool, Safety

IEC 62841-3-14:2017 applies to transportable drain cleaners. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Drain cleaners are also known as pipe cleaners. This standard does not apply to hand-held drain cleaners. Hand-held drain cleaners are covered by IEC 62841-2-21. This standard does not apply to high pressure cleaners to clean drains. High pressure cleaners are covered by IEC 60335-2-79. This standard does not apply to machines that use a solid rod to clean drains This Part 3-14 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

2019-11-14: this prAA represents common mods. to EN 62841-3-1:2014/prA1 (PR=70783)
D164/C043: DOW= DOR+48 months

No scope available

This part of IEC 62841 applies to hand-held grinders, disc-type polishers and disc-type sanders, including angle, straight and vertical tools, intended for use on various materials except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no-load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity.

IEC 62841-2-3:2020: applies to hand-held grinders, disc-type polishers and disc-type sanders, including angle, straight and vertical tools, intended for use on various materials except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no-load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity. This standard does not apply to dedicated cut-off machines. This standard does not apply to orbital polishers and orbital sanders. This standard does not apply to die grinders. This Part 2-3 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

IEC 62841-3-7:2020 This document applies to transportable wall saws guided by a track guiding system intended for dry cutting or to be connected to a liquid system for cutting concrete, stone or similar material by means of a diamond wheel. The rated speed of the diamond wheel does not exceed a peripheral speed of 100 m/s at rated capacity. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. This document does not apply to transportable wall saws that are intended to be left unattended while performing an operation. This document does not apply to transportable wall saws that employ hydraulic systems. This document does not apply to hand-held cut-off machines.

This standard applies to transportable wall saws guided by a track guiding system intended for dry cutting or to be connected to a liquid system for cutting concrete, stone or similar material by means of a diamond wheel. The rated speed of the diamond wheel does not exceed a peripheral speed of 100 m/s at rated capacity.

IEC 62841-3-13:2017 applies to transportable drills, with manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This part of IEC 62841 does not apply to magnetic drill stands and drill motors. This Part 3-13 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drills, Hand-held tool, Safety

IEC 62841-2-10:2017 applies to mixers the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Mixers are not considered to be tools with a liquid system. This standard does not apply to drills and impact drills, even if they can be used as a mixer This Part 2-10 is to be used in conjunction with the first edition of IEC 62841-1:2014 . The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Mixer, Hand-held tool, Safety

2020-05-08: no xml because common mod
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series
2019-07-05: to be launched to the enquiry together with pr = 70011 (SV)
2019-07-05: Represents common mods. to EN 62841-2-6 (PR=70011)

IEC 62841-2-6:2020 Tools covered by this document include percussion hammers and rotary hammers, including rotary hammers with the capability to rotate only with the percussion system disengaged (drill only mode). The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. This document does not apply to drills and impact drills. This document does not apply to tools that are designed exclusively for driving fasteners, such as palm nailers.

This standard applies to transportable bench grinders that can be equipped with one or two accessories as follows: - type 1 grinding wheels in accordance with ISO 603-4 with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm; - wire brushes with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm; - polishing wheels with a diameter not exceeding 310 mm; and with a peripheral speed of any accessory between 10 m/s and 50 m/s. NOTE Polishing wheels are also known as buffing wheels.

2020-12-01: common mod -no xml
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series
2018-11-02: this prA covers common mods to prEN IEC 62841-3-9 (PR=67950)
2021: CLC legacy converted by DCLab NISOSTS

IEC 62841-3-9:2020 is available as IEC 62841-3-9:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62841-3-9:2020 applies to transportable mitre saws intended to be used with a toothed saw blade for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter not exceeding 410 mm, which hereinafter might simply be referred to as saw or tool. This International Standard does not apply to mitre saws intended to cut other metals, such as magnesium, steel and iron. This document does not apply to mitre saws with an automatic feeding device. Transportable saws intended to cut ferrous metals will be covered by a future part of IEC 62841-3. This document does not apply to saws designed for use with abrasive wheels. Transportable tools designed for use with abrasive wheels are covered by IEC 62841-3-10. This document does not apply to tools combining the function of a mitre saw with the function of a table saw. Transportable tools combining the function of a mitre saw with the function of a table saw are covered by by a future part of IEC 62841-3. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - Clause 1: Scope: increase of the maximum saw blade diameter to 410 mm; - Corrigendum 1 and Corrigendum 2 of the first edition have been incorporated in this second edition. This Part 3-9 is to be used in conjunction with the IEC 62841-1:2014. Key words: Hand-Held Tools, Transportable Mitre Saw

2020-01-06 JF: the Annex ZZ which had been approved by  the BT is not the most recent one -> need to submit the correct Annex ZZ to the BT. The BT document under preparation.
2019-11-05 JF: Through the BT decision D163/C100, the BT approved the revised Annex ZZ of the standard. Standard under publlication.
NEXT ACTION: CCMC ACTION BY 2019-08-30: submission of the revised Annex ZZ for the BT approval.
Compliant assessment of the Annex ZA received.
2019-05-08 JF: HAS Consultants confirmed that the request for assessment will be accepted but asked to  issue a new request by CCMC. CCMC made a new request. The indicative deadline to receive it: 2019-06-12
2019-04-19 JF: EC clarified that HAS Consutlants will carry out the assessment of the corrected Annex ZZ. NEXT ACTION: HAS CONSULTANT ASSESSMENT EXPECTED BY 2019-05-23.
2019-01-30 Assessment request rejected by HAS Consultants on the grounds that it is a second requset at this stage. CCMC asked the EC to clarify.
2019-

IEC 62841-2-8:2016 applies to hand-held shears and nibblers the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Keywords: Shear, Nibbler, Hand-held tool, Transportable tool This publication is to be read in conjunction with IEC 62841-1:2014.

2020-12-01: common mod - no xml
2018-11-02: this prA covers common mods to EN 62841-3-4:2016/prA1:2018 (pr=67898)
2021: CLC legacy converted by DCLab NISOSTS

Next steps: the formal vote of the European Amendment
2019-08-08 JF: The Annex ZZ was delivered after the Enquiry started. The need to adapt the Annex ZZ.

IEC 62841-2-11:2015 applies to applies to reciprocating saws such as jig saws and sabre saws.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-11 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: reciprocating saw, jig saw, sabre saw, hand-held tool, transportable tool

2017-03-16 SW: DOW=DOR+24 m.
2021: CLC legacy converted by DCLab NISOSTS

2017-03-16 SW: DOW=DOR+24 m.
2021: CLC legacy converted by DCLab NISOSTS

2017-03-16 SW: DOW=DOR+24 m.
2021: CLC legacy converted by DCLab NISOSTS

IEC 62841-3-10:2015(E) applies to transportable cut-off machines intended to cut materials such as metals, concrete and masonry and to be fitted with one abrasive bonded reinforced wheel of Type 41, or diamond cut-off wheel with the peripheral gaps, if any, not exceeding 10 mm and with a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s with the maximum wheel diameter and a wheel diameter range of 250 mm to 410 mm. This standard does not apply to: - transportable mitre saws; - transportable tile saws or transportable metal saws. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. This publication is to be read in conjunction with IEC 62841-1:2014. Key words: Hand-held tools, Transportable tools, Cut-off machines

IEC 62841-2-14:2015(E) applies to hand-held planners the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-14 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Planner, Hand held, Cutting head

IEC 62841-2-9:2015 applies to hand-held tappers and threaders. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Tapper, Threader, Internal Screw Threads, External Screw Threads This publication is to be read in conjunction with

IEC 62841-2-2:2014 deals with the safety of electric motor-operated or magnetically driven hand-held screwdrivers and impact wrenches. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 2-2 is to be used in conjunction with the first edition of IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Hand-held, Screwdriver, Impact wrench

IEC 62841-2-4:2014 applies to hand-held sanders and polishers with the exception of disc-type tools covered by IEC 62841-2-3. Tools covered by this standard include but are not limited to belt sanders, drum sanders or polishers, reciprocating sanders or polishers, orbital sanders or polishers and random orbit sanders or polishers. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Sander, Polisher, Belt, Drum Orbital, Reciprocating, Random Orbit This publication is to be read in conjunction with IEC 62841-1:2014.

IEC 62841-2-5:2014 applies to hand-held circular saws. This standard does not apply to saws designed for use with abrasive wheels. Saws designed for use with abrasive wheels as cut-off machines are covered by IEC 62841-2-22. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Saw, Circular, Cutting, This publication is to be read in conjunction with IEC 62841-1:2014.

IEC 62841-3-6:2014 applies to transportable diamond drills, intended to be connected to a liquid system. The liquid system may include liquid from a pipe or container. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. This Part 3-6 is to be used in conjunction with IEC 62841-1. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Diamond drill, Drill unit, Drill stand

IEC 62841-3-1:2014 applies to transportable table saws with: - a toothed single blade; or - stacked blades that cut a single groove or slot; or - a moulding head cutter intended for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter between 105 mm and 315 mm, which hereinafter may simply be referred to as saw or tool. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. This standard does not apply to table saws intended to cut other metals, such as magnesium, steel and iron. This standard does not apply to table saws with an automatic feeding device. This standard does not apply to saws designed for use with abrasive wheels. This standard does not apply to table saws with more than one spindle such as for a scoring blade. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Table Saw, Transportable This publication is to be read in conjunction with IEC 62841-1:2014.

IEC 62841-2-1:2017 applies to hand-held drills and impact drills, including diamond core drills. This standard also applies to drills that can be used for driving screws by attaching screwdriver bits.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This standard does not apply to rotary hammers, even if they can be used as a drill. This Part 2-1 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drill, Impact Drill, Hand-held tool, Safety