EN 60851-3:2009/A1:2013
(Amendment)Winding wires - Test methods - Part 3: Mechanical properties
Winding wires - Test methods - Part 3: Mechanical properties
2013-08-13 - Publication allocated to aclausse@cencenelec.eu
Wickeldrähte - Prüfverfahren - Teil 3: Mechanische Eigenschaften
Fils de bobinage - Méthodes d'essai - Partie 3: Propriétés mécaniques
Navijalne žice - Preskusne metode - 3. del: Mehanske lastnosti - Dopolnilo A1 (IEC 60851-3:2009/A1:2013)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2014
Navijalne žice - Preskusne metode - 3. del: Mehanske lastnosti - Dopolnilo A1 (IEC
60851-3:2009/A1:2013)
Winding wires - Test methods - Part 3: Mechanical properties
Wickeldrähte - Prüfverfahren - Teil 3: Mechanische Eigenschaften
Fils de bobinage - Méthodes d'essai - Partie 3: Propriétés mécaniques
Ta slovenski standard je istoveten z: EN 60851-3:2009/A1:2013
ICS:
29.060.10 Žice Wires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60851-3/A1
NORME EUROPÉENNE
September 2013
EUROPÄISCHE NORM
ICS 29.060.10
English version
Winding wires -
Test methods -
Part 3: Mechanical properties
(IEC 60851-3:2009/A1:2013)
Fils de bobinage - Wickeldrähte -
Méthodes d'essai - Prüfverfahren -
Partie 3: Propriétés mécaniques Teil 3: Mechanische Eigenschaften
(CEI 60851-3:2009/A1:2013) (IEC 60851-3:2009/A1:2013)
This amendment A1 modifies the European Standard EN 60851-3:2009; it was approved by CENELEC on 2013-
09-04. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate
the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60851-3:2009/A1:2013 E
Foreword
The text of document 55/1392/FDIS, future IEC 60851-3:2009/A1, prepared by IEC/TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2014-06-04
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2016-09-04
the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60851-3:2009/A1:2013 was approved by CENELEC as a
European Standard without any modification.
IEC 60851-3 ®
Edition 3.0 2013-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
AMENDMENT 1
AMENDEMENT 1
Winding wires – Test methods –
Part 3: Mechanical properties
Fils de bobinage – Méthodes d'essai –
Partie 3: Propriétés mécaniques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX H
ICS 29.060.10 ISBN 978-2-8322-1004-8
– 2 – 60851-3 Amend. 1 © IEC:2013
FOREWORD
This amendment has been prepared by IEC technical committee 55: Winding wires.
The text of this amendment is based on the following documents:
FDIS Report on voting
55/1392/FDIS 55/1407/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
_____________
60851-3 Amend. 1 © IEC:2013 – 3 –
B.1 General
Replace this subclause by the following:
This annex provides recommendations to the purchaser and supplier of winding wires with
respect to friction test methods to be used for winding wires. The use of additional methods
can be agreed upon between purchaser and supplier.
B.4 Test C: Second dynamic coefficient of friction test method
Replace the entire clause by the following:
B.4 Test C: Second dynamic coefficient of friction test method (applicable to
enamelled round wires with a nominal conductor diameter from 0,050 mm
up to and including 1,600 mm)
B.4.1 Test equipment
The design of typical test equipment is illustrated in Figure B.3. Figure B.4 contains detailed
drawings of synthetic sapphires and Figure B.5 is a photograph of the load block. The tester
is supplied with a wire guiding system and a take-up which pulls the wire over the test bed at
15 m/min as shown in Figure B.6. The test block is aligned parallel with the test bed and the
test weights are perpendicular to the wire specimen.
As the wire is pulled under the test block (synthetic sapphires), the friction between the wire
surface and the sapphire surface develops a longitudinal force, which is transferred to the
measuring system by a shaft supported by two sets of linear ball bearings in contact with the
measuring system. The force indicated by the measuring system is divided by the load on the
test surface to obtain the dynamic coefficient of friction.
The measuring system in Figure B.3 shows
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.