EN IEC 60695-1-14:2026
(Main)Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products
- Status
- Not Published
- Publication Date
- 26-Nov-2026
- Technical Committee
- CLC/SR 89 - Fire hazard testing
- Current Stage
- 4060 - Enquiry results established and sent to TC, SR, BTTF - Enquiry
- Start Date
- 05-Dec-2025
- Completion Date
- 05-Dec-2025
EN IEC 60695-1-14:2026 is a CENELEC standard from the International Electrotechnical Commission (IEC) that gives guidance on power and energy levels linked to ignition and fire in low voltage electrotechnical products. It helps Product Committees judge when an electrical energy source is unlikely to ignite materials, when a fire hazard safeguard should be used, and when extra protection against fire spread is needed.
What does EN IEC 60695-1-14:2026 specify?
EN IEC 60695-1-14:2026 provides guidance for low voltage electrotechnical products used in normal atmospheres commonly available in the home. It is intended for IEC technical committees and Product Committees when preparing or revising product standards for their own applications.
The scope focuses on electrical energy that may be dissipated as heat and used as a basis for fire hazard safeguards. It excludes special locations such as explosive atmospheres. The document is organized into scope, normative references, terms and definitions, electrical energy as a cause of ignition, empirical safety values of electrical power and energy, and a bibliography.
What are the key requirements of EN IEC 60695-1-14:2026?
EN IEC 60695-1-14:2026 is guidance rather than a product test standard. Its main message is that Product Committees should classify electrical energy sources by their ability to cause ignition and then decide what safeguards are appropriate for the product under consideration.
How should the classification be used?
Clause 5 says the classification can be applied to any part, circuit, or end product. The standard uses both power/time thinking and an alternative energy-based view, because the practical risk depends on how much energy is available and for how long. In practice, this helps a committee choose whether to rely on inherent limits, insulation, separation distance, or enclosure design.
What does Class 1 mean?
Clause 5.2 describes Class 1 as an electrical energy source considered unlikely to cause ignition under most circumstances. The practical takeaway is that a source below the stated low power level is normally treated as a safe energy level, so a fire hazard safeguard is usually not needed. The clause also notes that thermal insulation can change the picture, so the surrounding construction still matters.
What does Class 2 mean?
Clause 5.3 treats Class 2 as a source that may cause ignition under certain circumstances, so a fire hazard safeguard should be used. The standard links this to a controlled limit on available power and explains that practical safeguards are typically isolation and use of materials with suitable resistance to ignition. For a reader, this means the product may be allowed to have a potential ignition source, but nearby materials and layout must help contain the risk.
What does Class 3 mean?
Clause 5.4 treats Class 3 as a source likely to cause ignition and, if combustible material is present, fire spread. The document says a second fire hazard safeguard should be in place, such as a fire enclosure or a separation distance from nearby combustible material. In practice, this is the class where design must address not only ignition but also how fire is prevented from spreading.
How does the document help with power limits?
Clause 5 also gives practical guidance for low voltage installations, including the distinction between pluggable equipment type A, pluggable equipment type B, and permanently connected equipment. It uses the product of nominal mains voltage and overcurrent protective device rating to judge whether a circuit sits within the stated steady-state power level. That matters because the same equipment can fall into different design categories depending on how it is connected to the supply.
What terms does EN IEC 60695-1-14:2026 define?
- Fire hazard - a physical object or condition with the potential for an undesirable consequence from fire.
- Fire hazard safeguard - a part, system, or instruction intended to reduce ignition or fire spread; the document notes that this is often called a protection method.
- Ignition - the initiation of combustion.
- Low voltage equipment - electrical equipment with a supply or output voltage not exceeding 1 000 V AC or 1 500 V DC.
- Permanently connected equipment - equipment that can only be connected to or disconnected from the mains using a tool.
- Pluggable equipment type A - equipment intended for connection to the mains through a non-industrial plug and socket-outlet or appliance coupler.
- Pluggable equipment type B - equipment intended for connection to the mains through an industrial plug and socket-outlet or appliance coupler.
- Potential ignition source - a location where electrical energy can cause ignition.
Who uses EN IEC 60695-1-14:2026?
EN IEC 60695-1-14:2026 is aimed at IEC Product Committees and technical committees preparing product standards. It is also relevant to engineers working on low voltage electrotechnical products, especially where fire hazard safeguards have to be chosen during design.
The document is particularly useful in sectors covered by the referenced standards, including household appliances and audio/video, information and communication technology equipment. In those areas, the classification helps teams decide how much protection is needed around energized parts, wiring, and components.
Which standards are used with EN IEC 60695-1-14:2026?
- ISO/IEC Guide 51 - gives the general safety approach used when writing standards.
- ISO 13943:2017 - provides fire safety vocabulary used for the terms in this document.
- IEC GUIDE 104 - explains how to prepare and use basic safety publications.
- IEC GUIDE 116:2010 - gives guidance on safety-related risk assessment and risk reduction for low voltage equipment.
- IEC 60335-1:2020 - provides general safety requirements for household and similar electrical appliances.
- IEC 60695-1-10 and IEC 60695-1-11 - the companion parts used with this publication for fire hazard guidance and assessment.
- IEC 60695-4:2021 - supplies terminology for fire tests for electrotechnical products.
- IEC 60695-11-10:2013 - provides the 50 W flame test methods referenced in the rationale.
- IEC 62368-1:2023 - gives safety requirements for audio/video and ICT equipment, including related power source concepts.
What does the EN IEC 60695-1-14:2026 document contain?
Clause 4 explains how electrical energy can become a cause of ignition through arcing or resistive heating. It also discusses the factors that affect temperature rise, including material mass, heat capacity, heat loss, and geometry, and it notes that prediction can be complex.
Clause 5 sets out the empirical safety values used to classify power and energy sources into Classes 1, 2, and 3. The document includes Figure 1, which illustrates power/time limits, and Figure 2, which illustrates energy limits. These visuals support product design and fire hazard assessment by showing how the classifications are meant to be interpreted in practice.
Relations
- Effective Date
- 17-Nov-2026
Get Certified
Connect with accredited certification bodies for this standard

IMQ S.p.A. (Certification)
Italian electrical product certification.

SLG Prüf- und Zertifizierungs GmbH
German testing and certification body.

UL Solutions
Global safety science company with testing, inspection and certification.
Sponsored listings
Frequently Asked Questions
EN IEC 60695-1-14:2026 is a draft published by CLC. Its full title is "Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products". This standard covers: Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products
Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products
EN IEC 60695-1-14:2026 is classified under the following ICS (International Classification for Standards) categories: 13.220.40 - Ignitability and burning behaviour of materials and products; 29.020 - Electrical engineering in general. The ICS classification helps identify the subject area and facilitates finding related standards.
EN IEC 60695-1-14:2026 has the following relationships with other standards: It is inter standard links to EN IEC 60335-1:2023. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN IEC 60695-1-14:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2025
Preskušanje požarne ogroženosti - 1-14. del: Smernice o različnih ravneh moči in
energije, povezanih z verjetnostjo vžiga in požara v nizkonapetostnih
elektrotehničnih izdelkih
Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy
related to the probability of ignition and fire in low voltage electrotechnical products
Essais relatifs aux risques du feu - Partie 1-14: Recommandations relatives aux
différents niveaux de puissance et d'énergie liés à la probabilité d'inflammation et
d'incendie dans les produits électrotechniques à basse tension
Ta slovenski standard je istoveten z: prEN IEC 60695-1-14:2025
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
89/1619/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60695-1-14 ED2
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-09-12 2025-12-05
SUPERSEDES DOCUMENTS:
89/1605/CD, 89/1613/CC
IEC TC 89 : FIRE HAZARD TESTING
SECRETARIAT: SECRETARY:
Germany Mr Thorsten Ilg
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
TC 17,TC 22,TC 23,TC 34,TC 61,TC 66,TC
108,TC 121
ASPECTS CONCERNED:
Safety
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to
the probability of ignition and fire in low voltage electrotechnical products
PROPOSED STABILITY DATE: 2026
NOTE FROM TC/SC OFFICERS:
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it,
for any other purpose without permission in writing from IEC.
IEC CDV 60695-1-14 Ed.2 © IEC 2025
Link to Committee Draft for Vote (CDV) online document:
https://osd.iec.ch/#/editor/archive/17ca2b0d-43f3-8c54-e063-1810000a0e9a/en/CCDV/1
How to access
This link leads you to the Online Standards Development (OSD) platform for National Mirror
Committee’s (NMC) comments. The project draft may be found further down this document.
Resource materials
We recommend NCs to review the available materials to better understand the member
commenting on the OSD platform. This includes the:
• OSD NC roles overview
• How to add and submit comments to the IEC
Contact
Should you require any assistance, please contact the IEC IT Helpdesk.
IEC CDV 60695-1-14 Ed.2 © IEC 2025
CONTENTS
CONTENTS . 1
FOREWORD . 4
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Electrical energy as a cause of ignition . 10
5 Empirical safety values of electrical power and energy . 11
5.1 Different levels of power and electrical energy sources . 11
5.2 Electrical power and energy source that is unlikely to cause ignition (Class
1) . 12
5.3 Electrical power and energy source that may cause ignition (Class 2) . 12
5.4 Electrical power and energy source that is likely to cause ignition (Class 3) . 13
5.5 Graphical overview of the classification. 14
Bibliography . 16
Figure 1 – Illustration of power/time limits related to fire and ignition . 14
Figure 2 – Illustration of energy limits related to fire and ignition . 15
Table 1 – . 5
IEC CDV 60695-1-14 Ed.2 © IEC 2025
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Fire hazard testing -
Part 1-14: Guidance on the different levels of power and energy related to
the probability of ignition and fire in low voltage electrotechnical products
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for
standardization comprising all national electrotechnical committees (IEC National Committees).
The object of IEC is to promote international co-operation on all questions concerning
standardization in the electrical and electronic fields. To this end and in addition to other
activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National
Committee interested in the subject dealt with may participate in this preparatory work.
International, governmental and non-governmental organizations liaising with the IEC also
participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as
possible, an international consensus of opinion on the relevant subjects since each technical
committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted
by IEC National Committees in that sense. While all reasonable efforts are made to ensure that
the technical content of IEC Publications is accurate, IEC cannot be held responsible for the
way in which they are used or for any misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply
IEC Publications transparently to the maximum extent possible in their national and regional
publications. Any divergence between any IEC Publication and the corresponding national or
regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies
provide conformity assessment services and, in some areas, access to IEC marks of conformity.
IEC is not responsible for any services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including
individual experts and members of its technical committees and IEC National Committees for
any personal injury, property damage or other damage of any nature whatsoever, whether direct
or indirect, or for costs (including legal fees) and expenses arising out of the publication, use
of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced
publications is indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve
the use of (a) patent(s). IEC takes no position concerning the evidence, validity or applicability
of any claimed patent rights in respect thereof. As of the date of publication of this document,
IEC CDV 60695-1-14 Ed.2 © IEC 2025
IEC [had/had not] received notice of (a) patent(s), which may be required to implement this
document. However, implementers are cautioned that this may not represent the latest
information, which may be obtained from the patent database available at https://patents.iec.ch.
IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60695-1-14 has been prepared by IEC technical committee 89: Fire hazard testing. It is
an International Standard.
The text of this International Standard is based on the following documents:
Table 1 –
Enquiry draft Report on voting
89/1605/CD 89/1613/CC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Technical Specification is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
This publication is to be used in conjunction with IEC 60695-1-10 and IEC 60695-1-11.
A list of all the parts in the IEC 60695 series, under the general title Fire hazard testing, can be
found on the IEC website.
Part 1 consists of the following parts:
Part 1-10: Guidance for assessing the fire hazard of electrotechnical products – General
guidelines
Part 1-11: Guidance for assessing the fire hazard of electrotechnical products – Fire hazard
assessment
Part 1-12: Guidance for assessing the fire hazard of electrotechnical products – Fire safety
engineering
Part 1-14: Guidance on the different levels of power and energy related to the probability of
ignition and fire in low voltage electrotechnical products (this document)
Part 1-20: Guidance for assessing the fire hazard of electrotechnical products – Ignitability –
General guidance
Part 1-21: Guidance for assessing the fire hazard of electrotechnical products – Ignitability –
Summary and relevance of test methods
Part 1-30: Guidance for assessing the fire hazard of electrotechnical products – Preselection
testing process – General guidelines
Part 1-40: Guidance for assessing the fire hazard of electrotechnical products – Insulating
liquids
IEC CDV 60695-1-14 Ed.2 © IEC 2025
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
– reconfirmed,
– withdrawn, or
– revised.
IEC CDV 60695-1-14 Ed.2 © IEC 2025
INTRODUCTION
In the design of any electrotechnical product the risk of fire and the potential hazards associated
with fire need to be considered. In this respect the objective of component, circuit and
equipment design, as well as the choice of materials, is to reduce the risk of fire to a tolerable
level even in the event of reasonably foreseeable (mis)use, malfunction or failure.
IEC 60695‑1‑10 [1], IEC 60695‑1‑11 [2] and IEC 60695-1-12 [3] provide guidance on how this
is to be accomplished.
Fires involving electrotechnical products can be initiated from external non-electrical sources.
Considerations of this nature are dealt with in an overall fire hazard (3.1) assessment.
The aim of the IEC 60695 series of standards is to save lives and property by reducing the
number of fires or reducing the consequences of the fire. This can be accomplished by trying
to:
– prevent ignition (3.3) caused by an electrically energised component part and, in the event
of ignition (3.3), to confine any resulting fire within the bounds of the enclosure of the
electrotechnical product;
– minimize flame spread beyond the product’s enclosure and to minimise the harmful effects
of fire effluents including heat, smoke, and toxic or corrosive combustion products.
This standard provides guidance to Product Committees on the power levels and amounts of
energy that are likely to cause ignition (3.3) and fire. It also provides guidance to Product
Committees on the fire hazard safeguards (3.2) that might be necessary to protect against the
probability of ignition (3.3).
The probability of fire is highly dependent on the specific fire scenario within the electrotechnical
product itself. Therefore, product committees are ultimately responsible for deciding what fire
hazard safeguards (3.2) are appropriate for their products.
This standard was created due to a need (IEC technical committee 66) for guidance on electrical
energy levels in relation to ignition (3.3) and fire. The preparation of this standard is based on
electrical energy levels developed by TC 108, responsible for safety of audio, video and ICT
equipment.
IEC CDV 60695-1-14 Ed.2 © IEC 2025
1 Scope
This part of IEC 60695 provides guidance about the levels of power and energy that could cause
ignition (3.3) and fire in a low voltage electrotechnical product. It can be used by Product
Committees to determine what fire hazard safeguards (3.2) might be used, based on the
electrical energy that could be dissipated as heat.
This document deals with products used in normal atmospheres commonly available in the
home and does not deal with special locations such as those in explosive atmospheres. It is
intended as guidance to IEC committees, and is intended be used with respect to their individual
applications.
This basic safety publication is intended for use by technical committees in the preparation of
standards in accordance with the principles laid down in IEC GUIDE 104 and ISO/IEC Guide
51 .
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications in the preparation of its publications. The requirements, test methods
or test conditions of this basic safety publication will not apply unless specifically referred to or
included in the relevant publications.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
ISO/IEC Guide 51, Safety aspects — Guidelines for their inclusion in standards
ISO 13943:2017, Fire safety — Vocabulary
IEC GUIDE 104, The preparation of safety publications and the use of basic safety publications
and group safety publications
IEC GUIDE 116:2010, Guidelines for safety related risk assessment and risk reduction for low
voltage equipment
IEC 60335-1:2020, Household and similar electrical appliances - Safety - Part 1: General
requirements
IEC 60695-1-10, Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of
electrotechnical products - General guidelines
IEC 60695-1-11, Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of
electrotechnical products - Fire hazard assessment
IEC 60695-4:2021, Fire hazard testing - Part 4: Terminology concerning fire tests for
electrotechnical products
IEC 60695-11-10:2013, Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and
vertical flame test methods
IEC 62368-1:2023, Audio/video, information and communication technology equipment - Part
1: Safety requirements
IEC CDV 60695-1-14 Ed.2 © IEC 2025
The preparation of safety publications and the use of basic safety publications and group safety
publications
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60695-4:2021 and
ISO 13943:2017 (some of which are reproduced below) and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
fire hazard
physical object or condition with a potential for an undesirable consequence from fire
[SOURCE: ISO 13943:2017, 3.131]
3.2
...



