EN 61754-7:2008
(Main)Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7: Type MPO connector family
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7: Type MPO connector family
IEC 61754-7:2008(E) defines the standard interface dimensions for type MPO family of connectors. Specific technical changes in this edition involve the addition of an aligned key adaptor interface definition to address all existing MPO applications.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 7: Steckverbinderfamilie der Bauart MPO
Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces de connecteurs pour fibres optiques - Partie 7: Famille de connecteurs de type MPO
L'IEC 61754-7:2008 définit les dimensions d'interface normalisées pour la famille de connecteurs de type MPO. Cette troisième édition annule et remplace la deuxième édition parue en 2004. Cette troisième édition constitue une révision technique. Les modifications techniques spécifiques incluent l'ajout de la définition d'une interface de raccord à détrompeur aligné pour couvrir l'ensemble des applications MPO existantes. Mots clés: dimensions d'interface normalisées pour la famille de connecteurs de type MPO
Spojni vmesniki optičnih vlaken - 7. del: Družina spojnikov tipa MPO (IEC 61754-7:2008)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
1DGRPHãþD
SIST EN 61754-7:2005
6SRMQLYPHVQLNLRSWLþQLKYODNHQGHO 'UXåLQDVSRMQLNRYWLSD032 ,(&
Fibre optic connector interfaces - Part 7: Type MPO connector family (IEC 61754-
7:2008)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von
Lichtwellenleiter-Steckverbindern - Teil 7: Steckverbinderfamilie der Bauart MPO (IEC
61754-7:2008)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces de
connecteurs pour fibres optiques - Partie 7: Famille de connecteurs de type MPO (CEI
61754-7:2008)
Ta slovenski standard je istoveten z: EN 61754-7:2008
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 61754-7
NORME EUROPÉENNE
June 2008
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61754-7:2005
English version
Fibre optic interconnecting devices and passive components -
Fibre optic connector interfaces -
Part 7: Type MPO connector family
(IEC 61754-7:2008)
Dispositifs d'interconnexion Lichtwellenleiter -
et composants passifs à fibres optiques - Verbindungselemente
Interfaces de connecteurs und passive Bauteile -
pour fibres optiques - Steckgesichter von
Partie 7: Famille de connecteurs Lichtwellenleiter-Steckverbindern -
de type MPO Teil 7: Steckverbinderfamilie
(CEI 61754-7:2008) der Bauart MPO
(IEC 61754-7:2008)
This European Standard was approved by CENELEC on 2008-04-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61754-7:2008 E
Foreword
The text of document 86B/2581/CDV, future edition 3 of IEC 61754-7, prepared by SC 86B, Fibre optic
interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61754-7 on 2008-04-01.
This European Standard supersedes EN 61754-7:2005.
Specific technical changes involve the addition of an aligned key adaptor interface definition to address all
existing MPO applications
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-04-01
The International Electrotechnical Commission (IEC) and CENELEC draw attention to the fact that it is claimed that compliance with
this document may involve the use of a patent concerning MPO connectors.
The IEC and CENELEC take no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has assured the IEC that he/she is willing to negotiate licences under reasonable and non-
discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent
right is registered with the IEC. Information may be obtained from:
Intellectual Property Department,
Nippon Telegraph and Telephone Corporation,
20-2 Nishi-shinjuku 3-Chome Shinjukuku,
Tokyo 163-14, Japan.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those
identified above. IEC and CENELEC shall not be held responsible for identifying any or all such patent rights.
__________
Endorsement notice
The text of the International Standard IEC 61754-7:2008 was approved by CENELEC as a European
Standard without any modification.
__________
IEC 61754-7
Edition 3.0 2008-03
INTERNATIONAL
STANDARD
Fibre optic interconnecting devices and passive components – Fibre optic
connector interfaces –
Part 7: Type MPO connector family
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
U
ICS 33.180.20 ISBN 2-8318-9667-3
– 2 – 61754-7 © IEC:2008(E)
CONTENTS
FOREWORD.3
1 Scope.5
2 Description .5
3 Interfaces .5
Figure 1 – MPO connector configurations .6
Figure 2 – MPO female plug connector angled interface .7
Figure 3 – Optical datum target location diagrams .9
Figure 4 – Gauge pin.11
Figure 5 – Gauge for plug.12
Figure 6 – MPO male plug connector angled interface .13
Figure 7 – MPO adaptor interface.15
Figure 8 – MPO female plug connector flat interface.17
Figure 9 – MPO male plug connector flat interface.19
Figure 10 – MPO backplane housing interface .21
Figure 11 – MPO printed board housing interface .22
Figure 12 – MPO aligned key adaptor interface.27
Table 1 – Dimensions of the MPO female plug connector angled interface.8
Table 2 – Dimensions of the gauge pin.11
Table 3 – Dimensions of the gauge for plug.12
Table 4 – Dimensions of the MPO male plug connector angled interface.14
Table 5 – Dimensions of the MPO adaptor interface .16
Table 6 – Dimensions of the MPO female plug connector flat interface .18
Table 7 – Dimensions of the MPO male plug connector flat interface .20
Table 8 – Dimensions of the MPO backplane housing.23
Table 9 – Grade .24
Table 10 – Dimensions of the MPO printed board housing interface.26
Table 11 – Dimensions of the MPO aligned key adaptor interface .28
61754-7 © IEC:2008(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –
Part 7: Type MPO connector family
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed that compliance
with this document may involve the use of a patent concerning MPO connectors.
The IEC takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has assured the IEC that he/she is willing to negotiate licences under reasonable and
non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the
holder of this patent right is registered with the IEC. Information may be obtained from:
Intellectual Property Department,
Nippon Telegraph and Telephone Corporation,
20-2 Nishi-shinjuku 3-Chome Shinjukuku,
Tokyo 163-14, Japan.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights
other than those identified above. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61754-7 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
– 4 – 61754-7 © IEC:2008(E)
This third edition cancels and replaces the second edition published in 2004. This third edition
constitutes a technical revision.
Specific technical changes involve the addition of an aligned key adaptor interface definition to
address all existing MPO applications.
The text of this standard is based on the following documents:
CDV Report on voting
86/2581/CDV 86/2672/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 61754 series, under the general title Fibre optic interconnecting
devices and passive components – fibre optic connector interfaces, can be found on the IEC
website.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
___________
This new extended title will be applied to other parts of IEC 61754 as and when they are re-issued.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.