EN 60115-1:2001/A11:2007
(Amendment)Fixed resistors for use in electronic equipment - Part 1: Generic specification
Fixed resistors for use in electronic equipment - Part 1: Generic specification
CLC/TC 40XB request: not to be offered to IEC as purely European * Superseded by EN 60115-1:2011
Festwiderstände zur Verwendung in Geräten der Elektronik - Teil 1: Fachgrundspezifikation
Résistances fixes utilisées dans les équipements électroniques - Partie 1: Spécification générique
Fiksni upori za elektronsko opremo - 1. del: Rodovna specifikacija
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60115-1:2002/A11:2008
01-marec-2008
Fiksni upori za elektronsko opremo - 1. del: Rodovna specifikacija
Fixed resistors for use in electronic equipment - Part 1: Generic specification
Festwiderstände zur Verwendung in Geräten der Elektronik - Teil 1:
Fachgrundspezifikation
Résistances fixes utilisées dans les équipements électroniques - Partie 1: Spécification
générique
Ta slovenski standard je istoveten z: EN 60115-1:2001/A11:2007
ICS:
31.040.10
SIST EN 60115-1:2002/A11:2008 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 60115-1/A11
NORME EUROPÉENNE
December 2007
EUROPÄISCHE NORM
ICS 31.040.10
English version
Fixed resistors for use in electronic equipment -
Part 1: Generic specification
Résistances fixes utilisées Festwiderstände zur Verwendung
dans les équipements électroniques - in Geräten der Elektronik -
Partie 1: Spécification générique Teil 1: Fachgrundspezifikation
This amendment A11 modifies the European Standard EN 60115-1:2001; it was approved by CENELEC on
2007-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60115-1:2001/A11:2007 E
---------------------- Page: 2 ----------------------
EN 60115-1:2001/A11:2007 - 2 -
Foreword
This amendment to the European Standard EN 60115-1:2001 was prepared by the Technical Committee
CENELEC TC 40XB, Resistors.
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as
amendment A11 to EN 60115-1:2001 on 2007-12-01.
The following dates were fixed:
– latest date by which the amendment has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-12-01
– latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2010-12-01
__________
---------------------- Page: 3 ----------------------
- 3 - EN 60115-1:2001/A11:2007
1.2 Normative references
Delete the existing references to: CECC 00 114-2:1994, CECC 00 114-3:1999, EN 61000-4-2:1995,
EN 61760-1:1998 and EN 100114-6:1996.
Add the following references:
EN 60695-11-5, Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus,
confirmatory test arrangement and guidance (IEC 60695-11-5)
EN 61340-3-1, Electrostatics – Part 3-1: Methods for simulation of electrostatic effects – Human body model
(HBM) – Component testing (IEC 61340-3-1)
EN 61760-1, Surface mounting technology - Part 1: Standard method for the specification of surface
mounting components (SMDs) (IEC 61760-1)
IEC QC 001002-3:2005, IEC Quality Assessment System for Electronic Components (IECQ) – Rules of
procedure – Part 3: Approval procedures
IEC QC 001003, IEC Quality Assessment System for Electronic Components (IECQ) – Guidance documents
3 Quality assessment procedures
3.1 General
st
In the 1 paragraph replace
EN 100114-1 by QC 001002-3
nd
In the 2 paragraph replace
CECC 00 114-2 by QC 001002-3, Clause 3
CECC 00 114-3 by QC 001002-3, Clause 4
3.1.2.1
Replace the whole subclause by:
3.1.2.1 Capability Qualifying Components (CQCs), including process validation test
vehicles
A detail specification shall be prepared for each CQC as agreed with the National Supervising Inspectorate
(NSI). It shall identify the purpose of CQC and include all relevant test severities and limits.
3.1.2.2
Replace the whole subclause by:
3.1.2.2 Components for listing in the Register of Approvals (Standard catalogue items)
When the manufacturer desires that a resistor covered by the capability approval procedure should be listed
in the IECQ approvals database, a Capability Approval detail specification complying with the blank detail
specification shall be written. Such specifications shall be registered by the IECQ and the component may be
listed in the approvals section of the website www.iecq.org. See QC 001002-3, 4.4.3.
---------------------- Page: 4 ----------------------
EN 60115-1:2001/A11:2007 - 4 -
3.1.2.3 Customer specified resistors
st
In the 1 paragraph replace
4.3 of CECC 00 114-3 by QC 001002-3, 4.4.3
3.3 Subcontracting
st
In the 1 paragraph replace
1.2 of CECC 00 114-2 by QC 001002-3, 3.1.2
2.2 of CECC 00 114-3 by QC 001002-3, 4.2.2
nd
In the 2 paragraph replace
1.2.2 of CECC 00 114-2 by QC 001002-3, 3.1.2.2
2.2.2 of CECC 00 114-3 by QC 001002-3, 4.2.2.2
3.4 Structurally similar components
3.4.2
Replace the whole subclause by:
3.4.2 For failure rate level evaluation and determination, fixed resistors are accepted as being structurally
similar
a) when they are manufactured at one or at several manufacturing sites
• using the same specified raw-materials, manufacturing- and quality inspection- procedures and
• under the same responsibility for the product and quality of the leading manufacturing site.
When there are several manufacturing sites, the manufacturer shall nominate the prime site and the
associated Designated Management Representative (DMR).
b) when all manufacturing sites are supervised by the same National Supervising Inspectorate (NSI).
Preferably it should be the NSI of that country in which the leading manufacturing site is located,
c) when they have the same stability class and climatic category,
d) when they are different in dimensions only, and
e) when they have similar terminal types.
Resistors which differ only in c) may be considered as structural similar if the different requirements of the
stability class and/or the climatic category are judged separately in the final measurements.
3.5.1 Eligibility for qualification approval
Replace 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.