Test requirements for low voltage aerial bundled cable accessories - Part 4: Connectors

EN 50483 series applies to overhead line fittings for tensioning, supporting and connecting aerial bundled cables (ABC) of rated voltage U0/U (Um): 0,6/1 (1,2) kV. This Part 4 applies to connectors used for the electrical connection of ABC. The connectors are designed to be installed where either the main and/or branch cable is ABC as defined by HD 626. Tests described in this document are type tests.

Prüfanforderungen für Bauteile für isolierte Niederspannungsfreileitungen - Teil 4: Verbinder

Prescriptions relatives aux essais des accessoires pour réseaux aériens basse tension torsadés - Partie 4: Connecteurs

Zahteve za preskušanje pribora za nizkonapetostne izolirane nadzemne kable - 4. del: Spojke

General Information

Status
Not Published
Publication Date
05-Oct-2026
Current Stage
4020 - Enquiry circulated - Enquiry
Start Date
18-Oct-2024
Due Date
20-May-2025
Completion Date
18-Oct-2024

Relations

Buy Standard

Draft
prEN 50483-4:2024
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2024
Zahteve za preskušanje pribora za nizkonapetostne izolirane nadzemne kable - 4.
del: Spojke
Test requirements for low voltage aerial bundled cable accessories - Part 4: Connectors
Prüfanforderungen für Bauteile für isolierte Niederspannungsfreileitungen - Teil 4:
Verbinder
Prescriptions relatives aux essais des accessoires pour réseaux aériens basse tension
torsadés - Partie 4: Connecteurs
Ta slovenski standard je istoveten z: prEN 50483-4
ICS:
29.240.20 Daljnovodi Power transmission and
distribution lines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2024
ICS 29.240.20 Will supersede EN 50483-4:2009
English Version
Test requirements for low voltage aerial bundled cable
accessories - Part 4: Connectors
Prescriptions relatives aux essais des accessoires pour Prüfanforderungen für Bauteile für isolierte
réseaux aériens basse tension torsadés - Partie 4: Niederspannungsfreileitungen - Teil 4: Verbinder
Connecteurs
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2025-01-03.

It has been drawn up by CLC/TC 20.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 79846 Ref. No. prEN 50483-4 E

Contents Page
1 European foreword . 3
2 Introduction . 4
3 1 Scope . 5
4 2 Normative references . 5
5 3 Terms and definitions . 5
6 4 Symbols . 7
7 5 Characteristics . 7
8 6 Marking . 8
9 7 General test conditions . 8
10 7.1 Generalities . 8
11 7.2 Preconditioning of ABC . 8
12 8 Type tests . 8
13 8.1 IPC tests. 8
14 8.2 Pre-insulated through connectors (sleeve) . 23
15 8.3 Pre-insulated terminals (lugs) . 34
16 Annex A (informative) Temporary connectors – Temperature rise and overload test . 40
17 A.1 Principle . 40
18 A.2 Test arrangement . 40
19 A.3 Procedure . 42
20 Bibliography . 44

21 European foreword
22 This document [prEN 50483-4:2024] has been prepared by WG 11 of CLC/TC 20 “Electric cables”.
23 This document is currently submitted to the Enquiry.
24 The following dates are proposed:
• latest date by which the existence of this (doa) dav + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dav + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dav + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
25 This document will supersede EN 50483-4:2009 and all of its amendments and corrigenda (if any).
26 prEN 50483-4:2024 includes the following significant technical changes with respect to EN 50483-4:2009:
27 This is Part 4 of CENELEC standard EN 50483 “Test requirements for low voltage aerial bundled cable
28 accessories”, which has six parts:
29 — Part 1: Generalities;
30 — Part 2: Tension and suspension clamps, fittings and brackets for self supporting system;
31 — Part 3: Tension and suspension clamps for neutral messenger system;
32 — Part 4: Connectors;
33 — Part 5: Electrical ageing test;
34 — Part 6: Environmental testing.
35 Introduction
36 The objective of the EN 50483 series is to provide a method of testing the suitability of accessories when used
37 under normal operating conditions with low voltage aerial bundled cables (ABC) complying with HD 626.
38 This European Standard does not invalidate existing approvals of products achieved on the basis of national
39 standards and specifications and/or the demonstration of satisfactory service performance. However, products
40 approved according to such national standards or specifications cannot directly claim approval to this
41 European Standard. It may be possible, subject to agreement between the customer and the manufacturer
42 and/or the supplier, and/or the relevant conformity assessment body, to demonstrate that conformity to the
43 earlier standard can be used to claim conformity to this standard, provided an assessment is made of any
44 additional type testing that may need to be carried out. Any such additional testing that is part of a sequence
45 of testing cannot be done separately.
46 1 Scope
47 EN 50483 series applies to overhead line fittings for tensioning, supporting and connecting aerial bundled
48 cables (ABC) of rated voltage U /U (U ): 0,6/1 (1,2) kV.
0 m
49 This Part 4 applies to connectors used for the electrical connection of ABC.
50 The connectors are designed to be installed where either the main and/or branch cable is ABC as defined by
51 HD 626.
52 Tests described in this document are type tests.
53 2 Normative references
54 The following documents are referred to in the text in such a way that some or all of their content constitutes
55 requirements of this document. For dated references, only the edition cited applies. For undated references,
56 the latest edition of the referenced document (including any amendments) applies.
57 EN 50182, Conductors for overhead lines - Round wire concentric lay stranded conductors
58 EN 50483-1:2024, Test requirements for low voltage aerial bundled cable accessories
59 EN 50483-5:2024, Test requirements for low voltage aerial bundled cable accessories
60 EN 50483-6:2024, Test requirements for low voltage aerial bundled cable accessories
61 EN 60529:1991, Degrees of protection provided by enclosures (IP Code)
62 HD 626, Overhead distribution cables of rated voltage U /U(U ): 0,6/1 (1,2) kV
o m
63 IEC 60050-461, International Electrotechnical Vocabulary (IEV) – Part 461: Electric cables
64 3 Terms and definitions
65 For the purposes of this document, the terms and definitions given in IEC 60050-461 and the following apply.
66 ISO and IEC maintain terminology databases for use in standardization at the following addresses:
67 — ISO Online browsing platform: available at https://www.iso.org/obp/
68 — IEC Electropedia: available at https://www.electropedia.org/
69 3.1
70 aerial bundled cable (ABC)
71 aerial cable consisting of a group of insulated conductors which are twisted together including, or not, a non
72 insulated conductor
73 [SOURCE: IEV 461-08-02, modified]
74 Note 1 to entry: The terms bundled conductors, bundled cables, bundled cores, conductor bundles and bundle could be
75 used as equivalent to the term aerial bundled cable (ABC).
76 3.2
77 aerial-insulated-cable
78 insulated cable designed to be suspended overhead and outdoors
79 [SOURCE: IEV 461-08-01]
80 3.3
81 branch connector
82 metallic device for connecting a branch conductor to a main conductor at an intermediate point on the latter
83 [SOURCE: IEV 461-17-05]
84 3.4
85 branch conductor
86 conductor connected to the main conductor by a connector
87 3.5
88 conductor insulation
89 insulation applied on a conductor
90 [SOURCE: IEV 461-02-02, modified]
91 3.6
92 conductor (of a cable)
93 part of a cable which has the specific function of carrying current
94 [SOURCE: IEV 461-01-01]
95 3.7
96 connector
97 metallic device to connect cable conductors together
98 [SOURCE: IEV 461-17-03]
99 3.8
100 core
101 assembly comprising conductor and its own insulation
102 [SOURCE: IEV 461-04-04, modified]
103 3.9
104 insulation (of a cable)
105 insulating materials incorporated in a cable with the specific function of withstanding voltage [IEV 461-02-01]
106 3.10
107 insulation piercing connector (IPC)
108 connector in which electrical contact with the conductor is made by metallic protrusions which pierce the
109 insulation of the ABC core
110 [SOURCE: IEV 461-11-08, modified]
111 3.11
112 messenger
113 wire or rope, the primary function of which is to support the cable in aerial installations, which may be separate
114 from or integral with the cable it supports
115 [SOURCE: IEV 461-08-03]
116 3.12
117 minimum breaking load (MBL)
118 minimum breaking load of the conductor given by HD 626 or the cable manufacturer if not defined in the
119 standard or minimum breaking load of the clamp given by the clamp manufacturer
120 3.13
121 neutral messenger system
122 aerial insulated system where only the neutral messenger supports the ABC
123 3.14
124 pre-insulated (terminal) lug
125 insulated metallic device for connecting an insulated cable conductor to other electrical equipment
126 3.15
127 pre-insulated through connector (sleeve)
128 insulated metallic device for connecting two consecutive lengths of insulated conductors
129 3.16
130 rated tensile strength (RTS)
131 estimate of the conductor breaking load calculated using the specified tensile properties of the component
132 wires
133 [SOURCE: EN 50182:2001, 3.7]
134 3.17
135 reusable connector
136 connector for connecting ABC to stripped cable or bare conductor where only the branch connection can be
137 reused
138 3.18
139 self supporting system
140 aerial insulated system where all the cores of the ABC contribute to its support
141 3.19
142 sheath
143 uniform and continuous tubular covering of metallic or non metallic material, generally extruded
144 [SOURCE: IEV 461-05-03]
145 3.20
146 shear head
147 head of a bolt, or a device fitted over the head of a bolt or a nut, which is designed to break at a specified
148 torque
149 3.21
150 type test
151 test required to be made before supplying a type of material covered by this standard on a general
152 commercial basis, in order to demonstrate satisfactory performance characteristics to meet the intended
153 application
154 Note 1 to entry: These tests are of such a nature that, after they have been made, they need not be repeated unless
155 changes are made to the accessory materials, design or type of manufacturing pro
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.