Switches for appliances - Part 2-6: Particular requirements for switches used in electric motor-operated hand-held tools, transportable tools and lawn and garden machinery

Clause 1 of IEC 61058-1:2016 is applicable except as follows. Addition: This part of IEC 61058 is a subset based on IEC 61058-1. The clauses outlined below are intended to address the specific requirements for switches incorporated into or integrated with electric motor-operated hand-held tools, transportable tools and lawn and garden machinery. This document is intended for switches with an ambient temperature up to and including 55 °C. Switches tested according to IEC 61058-1 are considered to comply with this document and additional testing is not required provided ratings, loads, and endurance are correct. NOTE This document takes into account the fact that tests are conducted as part of the end-product evaluation (e.g. products tested according to the IEC 60745 and IEC 62841 series, and lawn and gardening equipment tested according to the IEC 60335 series), and that tests are not conducted on the component switch.

Geräteschalter - Teil 2-6: Besondere Anforderungen für Schalter zur Anwendung in elektromotorisch betätigten handgeführten Werkzeugen, transportablen Werkzeugen und Rasen- und Gartenmaschinen

Interrupteurs pour appareils - Partie 2-6: Exigences particulières pour les interrupteurs utilisés sur les outils électroportatifs à moteur, les outils portables et les machines pour jardins et pelouses

IEC 61058-2-6:2018 est disponible sous forme de IEC 61058-2-6:2018 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61058-2-6:2018 est un sous-ensemble basé sur l'IEC 61058-1. Les articles ci-après visent à répondre aux exigences spécifiques aux interrupteurs incorporés ou intégrés aux outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses. L'IEC e présent document s'applique aux interrupteurs destinés à être utilisés à une température ambiante inférieure ou égale à 55 °C. Les interrupteurs satisfaisant aux essais de l'IEC 61058-1 sont considérés conformes au présent document, et aucun essai supplémentaire n'est exigé si les caractéristiques assignées, les charges et l'endurance sont correctes. Cette deuxième édition annule et remplace la première édition parue en 2016, dont elle constitue une révision technique. Cette édition inclut la modification majeure suivante par rapport à l'édition précédente: Le format global a été modifié pour être compatible avec la structure révisée de l'IEC 61058-1, de l'IEC 61058-1-1 et de l'IEC 61058-1-2.

Stikala za aparate - 2-6. del: Posebne zahteve za stikala, ki se uporabljajo v električnih ročnih orodjih na motorni pogon, prenosnih orodjih ter strojih za trato in vrt (IEC 61058-2-6:2018)

Točka 1 standarda IEC 61058-1:2016 se uporablja, razen kot sledi.
Dodatek:
Ta del standarda IEC 61058 predstavlja podskupino standardov, ki temelji na standardu IEC 61058-1. Namen spodnjih točk je podati posebne zahteve za stikala, ki so sestavni del električnih ročnih orodij na motorni pogon, prenosnih orodij ter strojev za trato in vrt oziroma so vanje vgrajena.
Ta dokument se uporablja za stikala pri temperaturi okolja do vključno 55 °C. Stikala, preskušena v skladu s standardom IEC 61058-1, veljajo kot skladna s tem dokumentom in dodatni preskusi niso potrebni, če so vrednosti, obremenitve in vzdržljivost stikal pravilne.
OPOMBA: V dokumentu se upošteva, da se preskusi izvajajo kot del ocenjevanja končnih proizvodov (npr. proizvodov, ki so preskušeni skladno s skupinama standardov IEC 60745 in IEC 62841, ter opreme za trato in vrt, ki je preskušena skladno s skupino standardov IEC 60335) in da se preskusi ne izvajajo na stikalu komponente.

General Information

Status
Published
Publication Date
10-Jan-2019
Withdrawal Date
27-Dec-2021
Current Stage
6060 - Document made available - Publishing
Start Date
11-Jan-2019
Completion Date
11-Jan-2019

Relations

Buy Standard

Standard
EN 61058-2-6:2019
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN IEC 61058-2-6:2019
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
SIST EN 61058-2-6:2019
01-april-2019
1DGRPHãþD
SIST EN 61058-2-6:2017
6WLNDOD]DDSDUDWHGHO3RVHEQH]DKWHYH]DVWLNDODNLVHXSRUDEOMDMRY
HOHNWULþQLKURþQLKRURGMLKQDPRWRUQLSRJRQSUHQRVQLKRURGMLKWHUVWURMLK]DWUDWR
LQYUW ,(&
Switches for appliances - Part 2-6: Particular requirements for switches used in electric
motor-operated hand-held tools, transportable tools and lawn and garden machinery
(IEC 61058-2-6:2018)
Geräteschalter - Teil 2-6: Besondere Anforderungen für Schalter zur Anwendung in
elektromotorisch betätigten handgeführten Werkzeugen, transportablen Werkzeugen und
Rasen- und Gartenmaschinen (IEC 61058-2-6:2018)
Interrupteurs pour appareils - Partie 2-6: Exigences particulières pour les interrupteurs
utilisés sur les outils électroportatifs à moteur, les outils portables et les machines pour
jardins et pelouses (IEC 61058-2-6:2018)
Ta slovenski standard je istoveten z: EN IEC 61058-2-6:2019
ICS:
29.120.40 Stikala Switches
SIST EN 61058-2-6:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 61058-2-6:2019
SIST EN 61058-2-6:2019
EUROPEAN STANDARD EN IEC 61058-2-6

NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2019
ICS 29.120.40 Supersedes EN 61058-2-6:2016
English Version
Switches for appliances - Part 2-6: Particular requirements for
switches used in electric motor-operated hand-held tools,
transportable tools and lawn and garden machinery
(IEC 61058-2-6:2018)
Interrupteurs pour appareils - Partie 2-6: Exigences Geräteschalter - Teil 2-6: Besondere Anforderungen für
particulières pour les interrupteurs utilisés sur les outils Schalter zur Anwendung in elektromotorisch betätigten
électroportatifs à moteur, les outils portables et les handgeführten Werkzeugen, transportablen Werkzeugen
machines pour jardins et pelouses und Rasen- und Gartenmaschinen
(IEC 61058-2-6:2018) (IEC 61058-2-6:2018)
This European Standard was approved by CENELEC on 2018-12-28. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61058-2-6:2019 E

SIST EN 61058-2-6:2019
European foreword
The text of document 3J/450/FDIS, future edition 2 of IEC 61058-2-6, prepared by SC 23J "Switches
for appliances" of IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 61058-2-6:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-09-28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-12-28
document have to be withdrawn
This document supersedes EN 61058-2-6:2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61058-2-6:2018 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60745-1 NOTE Harmonized as EN 60745-1
IEC 62841-1 NOTE Harmonized as EN 62841-1

SIST EN 61058-2-6:2019
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61058-1 2016 Switches for appliances - Part 1: General EN IEC 61058-1 2018
requirements
Clause 2 of IEC 61058-1:2016 is applicable.
SIST EN 61058-2-6:2019
SIST EN 61058-2-6:2019
IEC 61058-2-6 ®
Edition 2.0 2018-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Switches for appliances –
Part 2-6: Particular requirements for switches used in electric motor-operated

hand-held tools, transportable tools and lawn and garden machinery

Interrupteurs pour appareils –

Partie 2-6: Exigences particulières pour les interrupteurs utilisés sur les outils

électroportatifs à moteur, les outils portables et les machines pour jardins et

pelouses
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.40 ISBN 978-2-8322-6282-5

SIST EN 61058-2-6:2019
– 2 – IEC 61058-2-6:2018 © IEC 2018
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 General information on tests . 5
6 Rating . 5
7 Classification . 6
8 Marking and documentation . 6
9 Protection against electric shock . 7
10 Provision for earthing . 7
11 Terminals and terminations. 7
12 Construction . 7
13 Mechanism . 7
14 Protection against ingress of solid foreign objects, ingress of water and humid
conditions . 8
15 Insulation resistance and dielectric strength . 8
16 Heating . 9
17 Endurance – Mechanical switches . 9
18 Mechanical strength . 14
19 Screws, current-carrying parts and connections . 14
20 Clearances, creepage distances, solid insulation and coatings of rigid printed
board assemblies . 14
21 Fire hazard . 14
22 Resistance to rusting . 15
23 Abnormal operation and fault conditions for switches. 15
24 Components for switches . 15
25 EMC requirements . 16
Annexes . 17
Annex D (informative) Switch application guide . 18
Annex H (normative) Altitude correction factors . 19
Annex N (informative) Dimensions of tabs forming part of a switch . 20
Bibliography . 21

Table 3 – Switch information . 6
Table 201 – Test loads for electrical endurance tests for AC circuits . 12
Table 202 – Test loads for electrical endurance tests for DC circuits . 12

SIST EN 61058-2-6:2019
IEC 61058-2-6:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SWITCHES FOR APPLIANCES –
Part 2-6: Particular requirements for switches used
in electric motor-operated hand-held tools, transportable
tools and lawn and garden machinery

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, o
...


SLOVENSKI STANDARD
01-april-2019
Nadomešča:
SIST EN 61058-2-6:2017
Stikala za aparate - 2-6. del: Posebne zahteve za stikala, ki se uporabljajo v
električnih ročnih orodjih na motorni pogon, prenosnih orodjih ter strojih za trato
in vrt (IEC 61058-2-6:2018)
Switches for appliances - Part 2-6: Particular requirements for switches used in electric
motor-operated hand-held tools, transportable tools and lawn and garden machinery
(IEC 61058-2-6:2018)
Geräteschalter - Teil 2-6: Besondere Anforderungen für Schalter zur Anwendung in
elektromotorisch betätigten handgeführten Werkzeugen, transportablen Werkzeugen
und Rasen- und Gartenmaschinen (IEC 61058-2-6:2018)
Interrupteurs pour appareils - Partie 2-6: Exigences particulières pour les interrupteurs
utilisés sur les outils électroportatifs à moteur, les outils portables et les machines pour
jardins et pelouses (IEC 61058-2-6:2018)
Ta slovenski standard je istoveten z: EN IEC 61058-2-6:2019
ICS:
29.120.40 Stikala Switches
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61058-2-6

NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2019
ICS 29.120.40 Supersedes EN 61058-2-6:2016
English Version
Switches for appliances - Part 2-6: Particular requirements for
switches used in electric motor-operated hand-held tools,
transportable tools and lawn and garden machinery
(IEC 61058-2-6:2018)
Interrupteurs pour appareils - Partie 2-6: Exigences Geräteschalter - Teil 2-6: Besondere Anforderungen für
particulières pour les interrupteurs utilisés sur les outils Schalter zur Anwendung in elektromotorisch betätigten
électroportatifs à moteur, les outils portables et les handgeführten Werkzeugen, transportablen Werkzeugen
machines pour jardins et pelouses und Rasen- und Gartenmaschinen
(IEC 61058-2-6:2018) (IEC 61058-2-6:2018)
This European Standard was approved by CENELEC on 2018-12-28. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61058-2-6:2019 E

European foreword
The text of document 3J/450/FDIS, future edition 2 of IEC 61058-2-6, prepared by SC 23J "Switches
for appliances" of IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN IEC 61058-2-6:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-09-28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-12-28
document have to be withdrawn
This document supersedes EN 61058-2-6:2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61058-2-6:2018 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60745-1 NOTE Harmonized as EN 60745-1
IEC 62841-1 NOTE Harmonized as EN 62841-1

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61058-1 2016 Switches for appliances - Part 1: General EN IEC 61058-1 2018
requirements
Clause 2 of IEC 61058-1:2016 is applicable.
IEC 61058-2-6 ®
Edition 2.0 2018-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Switches for appliances –
Part 2-6: Particular requirements for switches used in electric motor-operated

hand-held tools, transportable tools and lawn and garden machinery

Interrupteurs pour appareils –

Partie 2-6: Exigences particulières pour les interrupteurs utilisés sur les outils

électroportatifs à moteur, les outils portables et les machines pour jardins et

pelouses
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.40 ISBN 978-2-8322-6282-5

– 2 – IEC 61058-2-6:2018 © IEC 2018
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 General information on tests . 5
6 Rating . 5
7 Classification . 6
8 Marking and documentation . 6
9 Protection against electric shock . 7
10 Provision for earthing . 7
11 Terminals and terminations. 7
12 Construction . 7
13 Mechanism . 7
14 Protection against ingress of solid foreign objects, ingress of water and humid
conditions . 8
15 Insulation resistance and dielectric strength . 8
16 Heating . 9
17 Endurance – Mechanical switches . 9
18 Mechanical strength . 14
19 Screws, current-carrying parts and connections . 14
20 Clearances, creepage distances, solid insulation and coatings of rigid printed
board assemblies . 14
21 Fire hazard . 14
22 Resistance to rusting . 15
23 Abnormal operation and fault conditions for switches. 15
24 Components for switches . 15
25 EMC requirements . 16
Annexes . 17
Annex D (informative) Switch application guide . 18
Annex H (normative) Altitude correction factors . 19
Annex N (informative) Dimensions of tabs forming part of a switch . 20
Bibliography . 21

Table 3 – Switch information . 6
Table 201 – Test loads for electrical endurance tests for AC circuits . 12
Table 202 – Test loads for electrical endurance tests for DC circuits . 12

IEC 61058-2-6:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SWITCHES FOR APPLIANCES –
Part 2-6: Particular requirements for switches used
in electric motor-operated hand-held tools, transportable
tools and lawn and garden machinery

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.