EN 61019-1:2005

Surface acoustic wave (SAW) resonators - Part 1: Generic specification

Specifies the methods of test and general requirements for SAW resonators.

Oberflächenwellenresonatoren (OFW-Resonatoren) - Teil 1: Fachgrundspezifikation

Résonateurs à ondes acoustiques de surface (OAS) - Partie 1: Spécification générique

Specifies the methods of test and general requirements for SAW resonators.

Resonatorji za površinske akustične valove – 1. del: Generična specifikacija (IEC 61019-1:2004)

General Information

• Status: Published
• Publication Date: 12-Jan-2005
• Withdrawal Date: 30-Nov-2007
• ICS: 31.140 - Piezoelectric devices
• Technical Committee: CLC/SR 49 - Piezoelectric and dielectric devices for frequency control and selection
• Drafting Committee: IEC/TC 49 - IEC_TC_49
• Parallel Committee: IEC/TC 49 - IEC_TC_49
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 13-Jan-2005
• Completion Date: 13-Jan-2005
• Ref Project: SIST EN 61019-1:2005 - Surface acoustic wave (SAW) resonators -- Part 1: Generic specification

Standards Content (Sample)

SLOVENSKI SIST EN 61019-1:2005

STANDARD
december 2005
Resonatorji za površinske akustične valove – 1. del: Generična specifikacija
(IEC 61019-1:2004)
Surface acoustic wave (SAW) resonators – Part 1: Generic specification (IEC
61019-1:2004)
ICS 31.140 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 61019-1
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2005

ICS 31.140
English version
Surface acoustic wave (SAW) resonators
Part 1: Generic specification
(IEC 61019-1:2004)
Résonateurs à ondes acoustiques  Oberflächenwellenresonatoren
de surface (OAS) (OFW-Resonatoren)
Partie 1: Spécification générique Teil 1: Fachgrundspezifikation
(CEI 61019-1:2004) (IEC 61019-1:2004)

This European Standard was approved by CENELEC on 2004-12-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61019-1:2005 E
Foreword
The text of document 49/689/FDIS, future edition 1 of IEC 61019-1, prepared by IEC TC 49,
Piezoelectric and dielectric devices for frequency control and selection, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61019-1 on 2004-12-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-12-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61019-1:2004 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61019-1:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60027 Series Letter symbols to be used in electrical HD 60027 Series
technology HD 245
IEC 60050-561 1991 International Electrotechnical - -
Vocabulary (IEV)
Chapter 561: Piezoelectric devices for
frequency control and selection

1)
IEC 60068-1 1988 Environmental testing EN 60068-1 1994
Part 1: General and guidance
IEC 60068-2-1 1990 Part 2: Tests - Tests A: Cold EN 60068-2-1 1993

2)
IEC 60068-2-2 1974 Part 2: Tests - Tests B: Dry heat EN 60068-2-2 1993

IEC 60068-2-6 1995 Part 2: Tests - Test Fc: Vibration
+ corr. March 1995 (sinusoidal) EN 60068-2-6 1995

3)
IEC 60068-2-7 1983 Part 2: Tests - Test Ga: Acceleration, EN 60068-2-7 1993
steady state
IEC 60068-2-13 1983 Part 2: Tests - Test M: Low air pressure EN 60068-2-13 1999

4)
IEC 60068-2-14 1984 Part 2: Tests - Test N: Change of EN 60068-2-14 1999
temperature
IEC 60068-2-17 1994 Part 2: Tests - Test Q: Sealing EN 60068-2-17 1994

5)
IEC 60068-2-20 1979 Part 2: Tests - Test T: Soldering HD 323.2.20 S3 1988

IEC 60068-2-21 1999 Part 2-21: Tests - Test U: Robustness EN 60068-2-21 1999
of terminations and integral mounting
devices
1)
EN 60068-1 includes Corrigendum October 1988 + A1:1992 to IEC 60068-1.
2)
EN 60068-2-2 includes supplement A:1976 to IEC 60068-2-2.
3)
EN 60068-2-7 includes A1:1986 to IEC 60068-2-7.
4)
EN 60068-2-14 includes A1:1986 to IEC 60068-2-14.
5)
HD 323.2.20 S3 includes A2:1987 to IEC 60068-2-20.

Publication Year Title EN/HD Year
IEC 60068-2-27 1987 Part 2: Tests - Test Ea and guidance: EN 60068-2-27 1993
Shock
IEC 60068-2-29 1987 Part 2: Tests - Test Eb and guidance:
+ Corrigendum Bump EN 60068-2-29 1993

6)
IEC 60068-2-30 1980 Part 2: Tests - Test Db and guidance: EN 60068-2-30 1999
Damp heat, cyclic (12 + 12-hour cycle)

7)
IEC 60068-2-32 1975 Part 2: Tests - Test Ed: Free fall EN 60068-2-32 1993
(Procedure 1)
IEC 60068-2-45 1980 Part 2: Tests - Test Xa and guidance: EN 60068-2-45 1992
Immersion in cleaning solvents

IEC 60068-2-52 1996 Part 2: Tests - Test Kb: Salt mist, cyclic EN 60068-2-52 1996
(sodium chloride solution)
8)
IEC 60068-2-58 1999 Part 2-58: Tests - Test Td: Test EN 60068-2-58 1999
methods for solderability, resistance to
dissolution of metallization and to
soldering heat of surface mounting
devices (SMD)
IEC 60068-2-64 1993 Part 2: Test methods - Test Fh: EN 60068-2-64 1994
+ Corr. October 1993 Vibration, broad-band random (digital
control) and guidance
IEC 60068-2-78 2001 Part 2-78: Tests - Test Cab: Damp heat, EN 60068-2-78 2001
steady state
database
IEC 60617 Graphical symbols for diagrams - -

IEC 60122-1 2002 Quartz crystal units of assessed quality EN 60122-1 2002
Part 1: Generic specification
IEC 60444 Series Measurement of quartz crystal unit EN 60444 Series
parameters
IEC 61000-4-2 1995 Electromagnetic compatibility (EMC) EN 61000-4-2 1995
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61019-2 1995 Surface acoustic wave (SAW) EN 61019-2 1997
resonators
Part 2: Guide to the use
IEC 61019-3 1991 Part 3: Standard outlines and lead - -
connections
6)
EN 60068-2-30 includes A1:1985 to IEC 60068-2-30.
7)
EN 60068-2-32 includes A2:1990 to IEC 60068-2-32.
8)
EN 60068-2-58 is superseded by EN 60068-2-58:2004, which is based on IEC 60068-2-58:2004.

- 5 - EN 61019-1:2005
Publication Year Title EN/HD Year
IEC QC 001001 2002 IEC Quality assessment system for - -
electronic components (IECQ) - Basic
rules
IEC QC 001002-2
1998 IEC Quality Assessment System for - -
Electronic Components (IECQ) - Rules
of Procedure
Part 2: Documentation
IEC QC 001002-3
1998 Part 3: Approval procedures - -

IEC QC 001005 2003 IEC Quality assessment system for - -
electronic components (IECQ) -
Register of films, products and services
approved under the IECQ system,
including ISO 9000
ISO 1000 1992 SI units and recommendations for the - -
use of their multiples and of certain
other units
INTERNATIONAL IEC
STANDARD 61019-1
First edition
2004-11
Surface acoustic wave (SAW) resonators –
Part 1:
Generic specification
 IEC 2004  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale W
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 61019-1  IEC:2004(E)
CONTENTS
FOREWORD.4

1 Scope.6
2 Normative references .6
3 Order of precedence.8
4 Terms and definitions .8
4.1 General terms .8
4.2 Operational properties.11
5 Preferred values for ratings and characteristics .19
5.1 Standard nominal frequency values in megahertz (MHz) .19
5.2 Standard operating temperature ranges in degrees Celsius (°C) .19
5.3 Standard values of load capacitance in picofarads (pF).19
5.4 Standard levels of drive in milliwatts (mW) .19
5.5 Standard values of minimum insertion attenuation in decibels (dB).19
5.6 Standard climatic category .20
5.7 Bump severity .20
5.8 Vibration severity .20
5.9 Shock severity.20
5.10 Fine leak rate .21
6 Marking .21
6.1 Resonator marking .21
6.2 Package marking.21
7 Quality assessment procedures.21
7.1 Primary stage of manufacture.21
7.2 Structurally similar components.21
7.3 Subcontracting .22
7.4 Incorporated components .22
7.5 Manufacturer’s approval .22
7.6 Approval procedures .22
7.7 Procedures for capability approval .23
7.8 Procedures for qualification approval.23
7.9 Test procedures .24
7.10 Screening requirements .24
7.11 Rework and repair work.24
7.12 Certified records of released lots.24
7.13 Validity of release.24
7.14 Release for delivery .24
7.15 Unchecked parameters.24
8 Test and measurement procedures.24
8.1 General .24
8.2 Test and measurement conditions .25
8.3 Visual inspection .26

61019-1  IEC:2004(E) – 3 –
8.4 Dimensions and gauging procedures .26
8.5 Measurement method of one-port resonator .26
8.6 Measurement method of two-port resonator.28
8.7 Mechanical and environmental test procedures .32
8.8 Endurance test procedure .37

Figure 1 – Basic configurations of SAW resonators.9
Figure 2 – One-port resonator equivalent circuit .12
Figure 3 – Vector admittance diagram of a one-port SAW reson
...