EN IEC 61837-2:2018/prA2:2025
(Amendment)Amendment 2 - Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Part 2: Ceramic enclosures
Amendment 2 - Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Part 2: Ceramic enclosures
Oberflächenmontierbare piezoelektrische Bauteile zur Frequenzstabilisierung und -selektion - Norm-Gehäusemaße und Anschlüsse - Teil 2: Keramikgehäuse
Dispositifs piézoélectriques à montage en surface pour la commande et le choix de la fréquence - Encombrements normalisés et connexions des sorties - Partie 2: Enveloppes en céramique
Površinsko nameščeni piezoelektrični elementi za krmiljenje in izbiranje (filtriranje) frekvenc - Standardne mere in priključni kontakti - 2. del: Keramični okrovi - Dopolnilo A2
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2026
Površinsko nameščeni piezoelektrični elementi za krmiljenje in izbiranje
(filtriranje) frekvenc - Standardne mere in priključni kontakti - 2. del: Keramični
okrovi - Dopolnilo A2
Amendment 2 - Surface mounted piezoelectric devices for frequency control and
selection - Standard outlines and terminal lead connections - Part 2: Ceramic enclosures
Oberflächenmontierbare piezoelektrische Bauteile zur Frequenzstabilisierung und -
selektion - Norm-Gehäusemaße und Anschlüsse - Teil 2: Keramikgehäuse
Dispositifs piézoélectriques à montage en surface pour la commande et le choix de la
fréquence - Encombrements normalisés et connexions des sorties - Partie 2:
Enveloppes en céramique
Ta slovenski standard je istoveten z: EN IEC 61837-2:2018/prA2:2025
ICS:
31.140 Piezoelektrične naprave Piezoelectric devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
49/1523/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61837-2/AMD2 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-12-05 2026-02-27
SUPERSEDES DOCUMENTS:
49/1522/RR
IEC TC 49 : PIEZOELECTRIC, DIELECTRIC AND ELECTROSTATIC DEVICES AND ASSOCIATED MATERIALS FOR FREQUENCY
CONTROL, SELECTION AND DETECTION
SECRETARIAT: SECRETARY:
Japan Mr Masanobu Okazaki
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
THE CENELEC MEMBERS ARE INVITED TO VOTE THROUGH
THE CENELEC ONLINE VOTING SYSTEM.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Amendment 2 - Surface mounted piezoelectric devices for frequency control and selection -
Standard outlines and terminal lead connections - Part 2: Ceramic enclosures
PROPOSED STABILITY DATE: 2028
NOTE FROM TC/SC OFFICERS:
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, o r any part of it,
for any other purpose without permission in writing from IEC.
IEC CDV 61837-2/AMD2 ED3 © IEC 2025
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SURFACE MOUNTED PIEZOELECTRIC DEVICES FOR FREQUENCY
CONTROL AND SELECTION - STANDARD
OUTLINES AND TERMINAL LEAD CONNECTIONS -
PART 2: CERAMIC ENCLOSURES
AMENDMENT 2
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draw attention to the possibility that the implementation of this document may involve the use of (a) patent(s).
IEC take no position concerning the evidence, validity or applicability of any claimed patent rights in respect
thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which may
be required to implement this document. However, implementers are cautioned that this may not represent the
latest information, which may be obtained from the patent database available at https://patents.iec.ch patents.
IEC shall not be held responsible for identifying any
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...