iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60268-5:1996/A2:1996

(Amendment)

Sound system equipment - Part 5: Loudspeakers

Sound system equipment - Part 5: Loudspeakers

EN following parallel vote * Superseded by EN 60268-5:2003

Elektroakustische Geräte - Teil 5: Lautsprecher

Equipements pour systèmes électroacoustiques - Partie 5: Haut-parleurs

Sound system equipment -- Part 5: Loudspeakers (IEC 60268-5:1989/A2:1996)

General Information

Status
Withdrawn
Publication Date
08-Aug-1996
Withdrawal Date
31-Mar-1997
ICS
17.140.50 - Electroacoustics
33.160.50 - Accessories
Technical Committee
CLC/TC 100X - Audio, video and multimedia systems and equipment and related sub-systems
Drafting Committee
IEC/TC 100 - IEC_TC_100
Parallel Committee
IEC/TC 100 - IEC_TC_100
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Jun-2006
Completion Date
01-Jun-2006
Ref Project
SIST EN 60268-5:1999/A2:1999 - Sound system equipment -- Part 5: Loudspeakers

Relations

Replaced By
EN 60268-5:2003 - Sound system equipment - Part 5: Loudspeakers
Effective Date
29-Jan-2023
Amends
EN 60268-5:1996 - Sound system equipment - Part 5: Loudspeakers
Effective Date
29-Jan-2023

Buy Standard

EN 60268-5:1999/A2:1999EN 60268-5:1999/A2:1999
PreviousNext
Amendment
EN 60268-5:1999/A2:1999
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-1999
Sound system equipment -- Part 5: Loudspeakers (IEC 60268-5:1989/A2:1996)
Sound system equipment -- Part 5: Loudspeakers
Elektroakustische Geräte -- Teil 5: Lautsprecher
Equipements pour systèmes électroacoustiques -- Partie 5: Haut-parleurs
Ta slovenski standard je istoveten z: EN 60268-5:1996/A2:1996
ICS:
33.160.50 Pribor Accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- P
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 61842:2002(Main)
Microphones and earphones for speech communications
SIST EN 61842:2003

Applies to the microphone part and earphone part of handsets, headsets or earsets for speech communications, and also to the microphone units and earphone units of built-in handsets, headsets or earsets. Establishes definitions relating to these electroacoustic transducers, standardizes the characteristics to be specified and the relevant methods of measurement.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50332-3:2017(Main)
Sound system equipment: headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 3: Measurement method for sound dose management
SIST EN 50332-3:2017

This part 3 of EN 50332 specifies sound dose measurement, and the alerts associated, to reduce the risk of listeners developing hearing impairment when using a Personal Music Player (PMP). The standard does not cover exposure from other sources than PMPs.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61094-3:2016/AC:2017-01(Corrigendum)
Electroacoustics - Measurement microphones - Part 3: Primary method for free-field calibration of laboratory standard microphones by the reciprocity technique
SIST EN 61094-3:2016/AC:2017

IEC corrigendum

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61094-3:2016(Main)
Electroacoustics - Measurement microphones - Part 3: Primary method for free-field calibration of laboratory standard microphones by the reciprocity technique
SIST EN 61094-3:2016

IEC 61094-3:2016 specifies a primary method of determining the complex free-field sensitivity of laboratory standard microphones so as to establish a reproducible and accurate basis for the measurement of sound pressure under free-field conditions. It is applicable to laboratory standard microphones meeting the requirements of IEC 61094-1. It is intended for use by laboratories with highly experienced staff and specialized equipment. This second edition cancels and replaces the first edition published in 1995. This edition constitutes a technical revision.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50332-2:2013(Main)
Sound system equipment: Headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 2: Matching of sets with headphones if either or both are offered separately, or are offered as one package equipment but with standardised connectors between the two allowing to combine components of different manufacturers or different design
SIST EN 50332-2:2014

This Part 2 of EN 50332 specifies methods of measuring the matching values for the use of personal music players and headphones/earphones defined for the use with those and with standardised connectors allowing to combine components of different manufacturers or different design sold separately in order to avoid possible hearing impairment by excessive sound pressure resulting from them. Compared with “one-package sets“ the sound pressure level at the ear cannot be fixed by only one condition but needs at least two characteristics, one each for player and the headphones/earphones, defined by the matching values for their connection. Requirements for protection against excessive sound pressure from personal music players are given in EN 60950-1:2006/A12:2011 and EN 60065:2002/A12:2011.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50332-1:2013(Main)
Sound system equipment: Headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 1: General method for "one package equipment"
SIST EN 50332-1:2014

The scope of this European Standard is to set up a suitable measuring methodology allowing accurate measurement of the maximum sound pressure level produced by consumer's headphones and earphones when associated with personal music players. NOTE This standard does not apply to acoustically open or acoustically closed headphones associated with mains operated Hi-Fi home equipement nor does it apply to headphones for medical purposes (hard of hearing etc.) or to headphones or similar parts being part of active hearing protection systems. Other requirements for safety, e.g. for noise protection in offices and industry are not affected by this standard. Requested features:  The method should be reproducible and easily applicable to every type and shape of headphone or earphone available on the market (good mechanical adaptability).  As safety and health are addressed, the method should faithfully reflect the pressure level effective at the user's ear (good correlation with subjective tests) to support protection against excessive sound pressure from personal music players (the limits themselves are found in EN 60950-1:2006/A12:2011 and EN 60065:2002/A12:2011 respectively).  And finally, it is desirable to establish a global measuring procedure, including each component in the chain: Portable set + specific test signal + associated headphone or earphone. The standard is split into two parts:  Part 1 deals with sets provided as a package equipment by the manufacturer. In this case, "Personal music players" means the association of one set (compact cassette player, FM radio receiver, digital media player, streaming audio player…) with supplied headphones or earphones.  Part 2 gives guidelines to associate portable audio sets (FM radio receiver, digital media player, streaming audio player…) with headphones or earphones provided separately by any source. And the package sets with standardised connectors between the two allowing to combine components of different manufacturers or different design.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61842:2002(Main)
Microphones and earphones for speech communications
SIST EN 61842:2003

Applies to the microphone part and earphone part of handsets, headsets or earsets for speech communications, and also to the microphone units and earphone units of built-in handsets, headsets or earsets. Establishes definitions relating to these electroacoustic transducers, standardizes the characteristics to be specified and the relevant methods of measurement.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61094-4:1995(Main)
Measurement microphones - Part 4: Specifications for working standard microphones
SIST EN 61094-4:2002

Applies to working standard microphones. Specifies mechanical dimensions and certain electroacoustical characteristics for working standard microphones used in measuring systems for the determination of sound pressure to enable these microphones to be used as transfer standards in the calibration of acoustic measurement instruments.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-9:2024(Main)
Rotating electrical machines - Part 9: Noise limits
SIST EN IEC 60034-9:2025

IEC 60034-9:2021 specifies test methods for the determination of sound power level of rotating electrical machines and specifies maximum A-weighted sound power levels for factory acceptance testing of network-supplied, rotating electrical machines in accordance with lEC 60034-1, having methods of cooling according to lEC 60034-6 and degrees of protection according to lEC 60034-5, and having the following characteristics: - standard design, either AC or DC, without additional special electrical, mechanical, or acoustical modifications intended to reduce the sound power level - rated output from 1 kW (or kVA) up to and including 5 500 kW (or kVA) - rated speed not greater than 3 750 min–1 This fifth edition cancels and replaces the fourth edition, published in 2003 and its amendment 1, published in 2007. This edition includes the following significant technical changes with respect to the previous edition: a) In Table 2 and Table 3 cooling methods IC01, IC11, IC21 and IC31, IC71, IC81 are now covered. b) This edition adds Table 3 for 60 Hz machines, whereas Table 2, which covers only 50 Hz machines, has no change in levels. c) In Table 3, grade A is added to harmonize the highest levels seen in IEC and NEMA, whereas grade B was added to harmonize the lowest, more restrictive levels seen in IEC and NEMA. d) The clause “Determination of noise increments caused by converter supply” has been shifted to Annex B and renamed “Information on typical noise increments caused by converter supply”.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-12:2024(Main)
Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors
SIST EN IEC 60034-12:2025

IEC 60034-12:2024 is available as IEC 60034-12:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60034-12:2024 specifies the parameters for eight designs of starting performance of single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with IEC 60034‑1 that: - have a rated voltage up to 1 000 V; - are intended for direct-on-line or star-delta starting; - are rated on the basis of duty type S1; - are constructed to any degree of protection as defined in IEC 60034-5 and explosion protection. This document also applies to dual voltage motors provided that the flux saturation level is the same for both voltages. This fourth edition cancels and replaces the third edition published in 2016. Aligned with the requirements for explosion protected motors from TC31 WG27 - new clause on methods for measuring locked-rotor current and torque; - new informative annex on the general current and torque characteristics with locked rotor; - new informative annex on correction of voltage and frequency; - aligned with the requirements for explosion protected motors from TC31 WG27.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day