iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60832:1996

(Main)

Insulating poles (insulating sticks) and universal tool attachments (fittings) for live working

Insulating poles (insulating sticks) and universal tool attachments (fittings) for live working

Applies to insulating poles (insulating sticks), and tool attachments (fittings) and is divided into three chapters. Chapter I: Specifies the required characteristics for insulating poles with permanently attached fittings and the tests (electrical and mechanical) which should be satisfied by these tools. Chapter II: Specifies the required characteristics for parts which may be attached to and detached from the ends of poles described in Chapter I, and the tests which should be satisfied by these tools. Chapter Ill: Specifies the special clauses, applicable to insulating poles and universal tool attachments.

Isolierende Arbeitsstangen und zugehörige Arbeitsköpfe zum Arbeiten unter Spannung

Perches isolantes et outils adaptables pour travaux sous tension

S'applique aux perches isolantes et aux outils adaptables. Chapitre I: Traite des caractéristiques exigées pour les perches isolantes, munies d'embouts fixes, et des essais (électriques et mécaniques) auxquels doivent satisfaire ces outils. Chapitre II: Traite des caractéristiques exigées pour les outils qui peuvent être attachés ou détachés du bout des perches considérées dans le premier chapitre et traite des essais auxquels doivent atisfaire ces outils. Chapitre III: Traite des clauses spéciales applicables aux perches isolantes et aux outils adaptables.

Izolacijski drogovi (izolacijske palice) in univerzalni nastavki za orodja za delo pod napetostjo (IEC 60832:1988, spremenjen)

General Information

Status
Withdrawn
Publication Date
16-Jun-1996
Withdrawal Date
28-Feb-1997
ICS
13.340.20 - Head protective equipment
Technical Committee
CLC/TC 78 - Equipment and tools for live working
Drafting Committee
IEC/TC 78 - IEC_TC_78
Parallel Committee
IEC/TC 78 - IEC_TC_78
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Mar-2013
Completion Date
01-Mar-2013
Ref Project
SIST EN 60832:2001 - Insulating poles (insulating sticks) and universal tool attachments (fittings) for live working

Relations

Replaced By
EN 60832-1:2010 - Live working - Insulating sticks and attachable devices - Part 1: Insulating sticks
Effective Date
28-Jan-2023
Replaced By
EN 60832-2:2010 - Live working - Insulating sticks and attachable devices - Part 2: Attachable devices
Effective Date
28-Jan-2023

Buy Standard

EN 60832:2001EN 60832:2001
PreviousNext
Standard
EN 60832:2001
English language
69 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2001
Izolacijski drogovi (izolacijske palice) in univerzalni nastavki za orodja za delo pod
napetostjo (IEC 60832:1988, spremenjen)
Insulating poles (insulating sticks) and universal tool attachments (fittings) for live
working
Isolierende Arbeitsstangen und zugehörige Arbeitsköpfe zum Arbeiten unter Spannung
Perches isolantes et outils adaptables pour travaux sous tension
Ta slovenski standard je istoveten z: EN 60832:1996
ICS:
13.260 9DUVWYRSUHGHOHNWULþQLP Protection against electric
XGDURP'HORSRGQDSHWRVWMR shock. Live working
29.260.01 (OHNWULþQDRSUHPD]DGHORY Electrical equipment for
SRVHEQLKUD]PHUDKQD working in special conditions
VSORãQR in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

-
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50365:2023(Main)
Live Working - Electrically insulating helmets for use on low and medium voltage installations
SIST EN 50365:2024

This standard is applicable to electrically insulating helmets used for working live or close to live parts on installations not exceeding 1 000 V AC or 1 500 V DC. These helmets, when used in conjunction with other electrically insulating protective equipment prevent dangerous current from passing through persons via their head.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50365:2002(Main)
Electrically insulating helmets for use on low voltage installations
SIST EN 50365:2002

This standard is applicable to electrically insulating helmets used for working live or close to live parts on installations not exceeding 1 000 V a.c. or 1 500 V d.c. These helmets, when used in conjunction with other electrically insulating protective equipment prevent dangerous current from passing through persons via their head.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61235:1995(Main)
Live working - Insulating hollow tubes for electrical purposes
SIST EN 61235:2001

Applies to insulating hollow tubes made of synthetic materials and intended for tools and equipment for work on systems operating at voltages above 1 kV.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50365:2023(Main)
Live Working - Electrically insulating helmets for use on low and medium voltage installations
SIST EN 50365:2024

This standard is applicable to electrically insulating helmets used for working live or close to live parts on installations not exceeding 1 000 V AC or 1 500 V DC. These helmets, when used in conjunction with other electrically insulating protective equipment prevent dangerous current from passing through persons via their head.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50365:2002(Main)
Electrically insulating helmets for use on low voltage installations
SIST EN 50365:2002

This standard is applicable to electrically insulating helmets used for working live or close to live parts on installations not exceeding 1 000 V a.c. or 1 500 V d.c. These helmets, when used in conjunction with other electrically insulating protective equipment prevent dangerous current from passing through persons via their head.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61235:1995(Main)
Live working - Insulating hollow tubes for electrical purposes
SIST EN 61235:2001

Applies to insulating hollow tubes made of synthetic materials and intended for tools and equipment for work on systems operating at voltages above 1 kV.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-39:2024(Main)
Household and similar electrical appliances - Safety - Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans
kSIST FprEN 60335-2-39:2012

IEC 60335-2-39:2012 deals with the safety of electrically operated commercial multi-purpose cooking pans not intended for household and similar use, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. This standard also deals with pressurized appliances and appliances with pressurized parts. These appliances are used for processing food for commercial consumption, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries, butcheries, etc. The electrical part of appliances making use of other forms of energy is also within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by these types of appliances. Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. The principal changes in this edition as compared with the fifth edition of IEC 60335-2-39 are as follows (minor changes are not listed): - addition to definition of portable appliances, atmospheric multi-purpose cooking and rated pressure; - deletion of equipotential symbol 5021 of IEC 60417 covered by Part 1; - addition of instructions for multi-purpose cooking pans; - modification on leakage current permissible for portable class l appliances; - addition to abnormal test requirements; - addition to mechanical hazard test for multi-purpose cooking pans; - addition of construction test for multi-purpose cooking pans; - addition to construction requirements for lids and theirs grips; - addition to construction requirements for positioning of pressure reliefs; - addition to construction's fixed appliances which are moved forward and backward for cleaning purposes.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. Keywords: Multi-purpose cooking pans.

  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-9:2024(Main)
Rotating electrical machines - Part 9: Noise limits
SIST EN IEC 60034-9:2025

IEC 60034-9:2021 specifies test methods for the determination of sound power level of rotating electrical machines and specifies maximum A-weighted sound power levels for factory acceptance testing of network-supplied, rotating electrical machines in accordance with lEC 60034-1, having methods of cooling according to lEC 60034-6 and degrees of protection according to lEC 60034-5, and having the following characteristics: - standard design, either AC or DC, without additional special electrical, mechanical, or acoustical modifications intended to reduce the sound power level - rated output from 1 kW (or kVA) up to and including 5 500 kW (or kVA) - rated speed not greater than 3 750 min–1 This fifth edition cancels and replaces the fourth edition, published in 2003 and its amendment 1, published in 2007. This edition includes the following significant technical changes with respect to the previous edition: a) In Table 2 and Table 3 cooling methods IC01, IC11, IC21 and IC31, IC71, IC81 are now covered. b) This edition adds Table 3 for 60 Hz machines, whereas Table 2, which covers only 50 Hz machines, has no change in levels. c) In Table 3, grade A is added to harmonize the highest levels seen in IEC and NEMA, whereas grade B was added to harmonize the lowest, more restrictive levels seen in IEC and NEMA. d) The clause “Determination of noise increments caused by converter supply” has been shifted to Annex B and renamed “Information on typical noise increments caused by converter supply”.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60034-12:2024(Main)
Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors
SIST EN IEC 60034-12:2025

IEC 60034-12:2024 is available as IEC 60034-12:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60034-12:2024 specifies the parameters for eight designs of starting performance of single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with IEC 60034‑1 that: - have a rated voltage up to 1 000 V; - are intended for direct-on-line or star-delta starting; - are rated on the basis of duty type S1; - are constructed to any degree of protection as defined in IEC 60034-5 and explosion protection. This document also applies to dual voltage motors provided that the flux saturation level is the same for both voltages. This fourth edition cancels and replaces the third edition published in 2016. Aligned with the requirements for explosion protected motors from TC31 WG27 - new clause on methods for measuring locked-rotor current and torque; - new informative annex on the general current and torque characteristics with locked rotor; - new informative annex on correction of voltage and frequency; - aligned with the requirements for explosion protected motors from TC31 WG27.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60335-2-40:2024/A11:2024(Amendment)
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
kSIST prEN IEC 60335-2-40:2023/kFprAA:2024

This European Standard deals with the safety of electric heat pumps, sanitary hot water heat pumps and air conditioners, incorporating motor-compressors as well as hydronic fan coils units, dehumidifiers (with or without motor-compressors), thermoelectric heat pumps and partial units. Their maximum rated voltage being not more than 300 V for single phase appliances and 600 V for multi-phase appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day