IEC 62282-3-3:2007

Fuel cell technologies - Part 3-3: Stationary fuel cell power systems - Installation

Provides minimum safety requirements for the installation of indoor and outdoor stationary fuel cell power systems in compliance with IEC 62282-3-1; applies to the installation of systems intended for electrical connection to mains directly or with a transfer switch, or intended for a stand-alone power distribution system, or intended to provide AC or DC power.

Technologies des piles à combustible - Partie 3-3: Systèmes à piles à combustible stationnaires - Installation

Fournit les exigences de sécurité minimales pour l'installation intérieure et extérieure des systèmes à piles à combustible stationnaires conformément à la CEI 62282-3-1; s'applique à l'installation des systèmes destinés à être connectés au réseau électrique directement ou via un interrupteur de transfert, ou destinés à être un système de distribution d'énergie autonome, ou destinés à fournir de l'énergie à courant alternatif ou à courant continu.

General Information

• Status: Replaced
• Publication Date: 13-Nov-2007
• ICS: 27.070 - Fuel cells
• Technical Committee: TC 105 - Fuel cell technologies
• Drafting Committee: MT 204 - TC 105/MT 204
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 14-Jun-2012

Relations

• Replaced By: IEC 62282-3-300:2012 - Fuel cell technologies - Part 3-300: Stationary fuel cell power systems - Installation
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 62282-3-3
Edition 1.0 2007-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fuel cell technologies –
Part 3-3: Stationary fuel cell power systems – Installation

Technologies des piles à combustible –
Partie 3-3: Systèmes à piles à combustible stationnaires – Installation

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
IEC 62282-3-3
Edition 1.0 2007-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fuel cell technologies –
Part 3-3: Stationary fuel cell power systems – Installation

Technologies des piles à combustible –
Partie 3-3: Systèmes à piles à combustible stationnaires – Installation

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
Q
CODE PRIX
ICS 27.070 ISBN 2-8318-9372-0
– 2 – 62282-3-3 © IEC:2007
CONTENTS
FOREWORD.4
INTRODUCTION.6

1 Scope.7
2 Normative references .8
3 Terms and definitions .8
4 General safety requirements and strategy .10
5 Siting considerations .11
5.1 General siting.11
5.2 Outdoor installations .12
5.3 Indoor installations .12
5.3.1 Large fuel cell power systems.12
5.3.2 Small fuel cell power systems.12
5.4 Rooftop installation.12
6 Ventilation and exhaust .12
6.1 General .12
6.2 Ventilation .12
6.3 Exhaust system .13
6.4 Process purging and venting .13
7 Fire protection and gas detection.13
7.1 Fire protection and detection .13
7.1.1 Site fire protection .13
7.1.2 Combustible gas detection (indoor installations only).13
7.2 Fire prevention and emergency planning .14
8 Interconnections with site interfaces .14
8.1 General .14
8.2 Connections to fuel supplies – General .14
8.3 Fuel shut off and piping .14
8.4 Connections to auxiliary media supply and media disposal.14
8.4.1 Combustible auxiliary gases .14
8.4.2 Non combustible or inert auxiliary gases.14
8.4.3 Water .15
8.4.4 Waste water disposal .15
8.4.5 Discharge pipe .15
9 Environmental requirements .15
10 Approval tests .15
10.1 Gas leakage .15
10.2 Site specific shutdown devices .15
11 Maintenance tests .15
12 Documentation .15
12.1 Markings and instructions.15
12.2 Inspection checklist .16
12.3 Installation manual .16
12.4 User’s information manual.16
12.5 Maintenance manual .16

62282-3-3 © IEC:2007 – 3 –
Figure 1 – Fuel cell power system.7

– 4 – 62282-3-3 © IEC:2007
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________
FUEL CELL TECHNOLOGIES –
Part 3-3: Stationary fuel cell power systems –
Installation
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 62282-3-3 has been prepared by IEC technical committee 105:
Fuel cell technologies.
The text of this standard is based on the following documents:
FDIS Report on voting
105/152/FDIS 105/170/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

62282-3-3 © IEC:2007 – 5 –
A list of all parts of the IEC 62282 series, under the general title Fuel cell technologies, can
be found on the IEC website.
The committee has decided that the contents of
...