IEC 62282-2-100:2020/COR1:2023
(Corrigendum)Corrigendum 1 - Fuel cell technologies - Part 2-100: Fuel cell modules - Safety
Corrigendum 1 - Fuel cell technologies - Part 2-100: Fuel cell modules - Safety
Corrigendum 1 - Technologies des piles à combustible - Partie 2-100: Modules à piles à combustible - Sécurité
General Information
Relations
Standards Content (Sample)
IEC 62282-2-100:2020/COR1:2023 – 1 –
© IEC 2023
INTERNATIONAL ELECTROTECHNICAL COMMISSION
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
IEC 62282-2-100 IEC 62282-2-100
Edition 1.0 2020-05 Édition 1.0 2020-05
FUEL CELL TECHNOLOGIES – TECHNOLOGIES DES PILES À COMBUSTIBLE –
Part 2-100: Fuel cell modules – Safety Partie 2-100: Modules à piles à combusti
...
This May Also Interest You
IEC 62282-4-202:2023 covers performance test methods of fuel cell power systems intended to be used to power unmanned aircrafts, including general requirements, start-up, shutdown, power output, continuous running time, electric efficiency, data transmission, warning and monitoring, environmental compatibility, etc.
The scope of this document is limited to electrically powered unmanned aircrafts with a maximum take-off mass not exceeding 150 kg (i.e. level 5 or lower unmanned aircrafts (UAs)).
This document applies to fuel cell power systems with a rated output voltage not exceeding 220 V DC for outdoor use.
This document applies only to compressed gaseous hydrogen-fuelled fuel cell power systems.
- Standard41 pagesEnglish and French languagesale 15% off
IEC 62282-8-301:2023 specifies performance test methods of power-to-methane systems based on solid oxide cells (SOCs). Water, CO2, and electricity are supplied to the system to produce methane and oxygen.
This document is not intended to be applied to solid oxide fuel cell (SOFC) cell/stack assembly units for power generation purposes only, since these are covered in IEC 62282-7-2. In addition, the test methods for SOC cell/stack assembly units including reversible operation (without any methanation reactor) are already described in IEC 62282-8-101.
This document is intended to be used for data exchanges in commercial transactions between the system manufacturers and customers. Users of this document can selectively execute test items suitable for their purposes from those described in this document.
- Standard99 pagesEnglish and French languagesale 15% off
IEC 62282-4-102:2022 is available as IEC 62282-4-102:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 62282-4-102:2022 specifies the performance test methods of fuel cell power systems for propulsion and auxiliary power units (APU). This document covers fuel cell power systems for propulsion other than those for road vehicles. This document applies to gaseous hydrogen-fuelled fuel cell power systems and direct methanol fuel cell power systems for electrically powered industrial trucks. The following fuels are considered within the scope of this document:
- gaseous hydrogen, and
- methanol.
This document covers the fuel cell power system as defined in 3.7 and Figure 1. This document applies to DC type fuel cell power systems, with a rated output voltage not exceeding DC 150 V for indoor and outdoor use. This document covers fuel cell power systems whose fuel source container is permanently attached to either the industrial truck or the fuel cell power system.
This second edition cancels and replaces the first edition published in 2017. This edition includes the following significant technical changes with respect to the previous edition:
a. alignment of the Scope with the second edition of IEC 62282-4-101:2022;
b. deletion of terms and definitions (previous entries 3.5, 3.10, and 3.15);
c. addition of new terms in Clause 3: "delivered power" (3.13) and "regenerated power" (3.14);
d. revision of symbols and their meanings in alignment with those of IEC 62282-3-201;
e. replacement of "reference conditions" with "standard conditions" as seen in Clause 5;
f. revision of the test method for the accessory load voltage spike test (13.3.2);
g. addition of clarifications in Clause 14 (Power stability under operation);
h. addition of a checklist for performance criteria dealt with in this document (Annex C).
- Standard76 pagesEnglish and French languagesale 15% off
IEC 62282-4-600:2022 covers the requirements for the performance test methods of fuel cell/battery hybrid systems intended to be used for electrically powered applications for excavators. For this purpose, this document covers electrical performance and vibration tests for the fuel cell/battery hybrid system. This document also covers performance test methods which focus on vibration and other characteristics for balance of plant (BOP) installed in heavy-duty applications with fuel cell/battery hybrid system.
This document applies to both gaseous hydrogen-fuelled fuel cell power, liquid hydrogen-fuelled fuel cell power, direct methanol fuel cell power and battery hybrid power pack systems.
- Standard83 pagesEnglish and French languagesale 15% off
IEC 62282-4-101:2022 is available as IEC 62282-4-101:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 62282-4-101:2022 deals with safety of fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). This part of IEC 62282 covers safety requirements for fuel cell power systems intended to be used in electrically powered industrial trucks as defined in ISO 5053-1.except for: rough-terrain trucks; non-stacking low-lift straddle carriers; stacking high-lift straddle carriers; rough-terrain variable-reach trucks; slewing rough-terrain variable-reach trucks; variable-reach container handlers; pedestrian propelled trucks. This document applies to gaseous hydrogen-fueled fuel cell power systems and direct methanol fuel cell power systems for electrically powered industrial trucks. This document applies to DC type fuel cell power systems, with a rated output voltage not exceeding 150 V DC for indoor and outdoor use.This second edition cancels and replaces the first edition published in 2014.This edition includes the following significant technical changes with respect to the previous edition:
- revision of the title of this document;
- revision of reference standards;
- addition of new subclauses (4.3, 4.14.5, 4.15.3, 4.15.4, 4.16, 5.6, and 5.23);
- previous 4.15 was revised as “4.16 Risk assessment and risk reduction”;
- revision of 4.6 3), access to the manual shutoff valve;
- revision of requirements for battery terminals that are threaded (4.14.10.1);
- revision of requirements for double layer capacitors (4.14.10.2);
- revision of external leakage test (5.5) and ultimate strength test (5.7);
- revision of temperature limits on capacitors depending on the temperature rating of the material (Table 3);
- revision of markings that are not relevant (Clause 7);
- added “Significant hazards, hazardous situations and events dealt with in this document” as a new informative annex
- Standard104 pagesEnglish and French languagesale 15% off
- Standard24 pagesEnglish and French languagesale 15% off
IEC 62282-7-2:2021 applies to SOFC cell/stack assembly units, testing systems, instruments and measuring methods, and specifies test methods to test the performance of SOFC cells and stacks. This document is not applicable to small button cells that are designed for SOFC material testing and provide no practical means of fuel utilization measurement. This document is used based on the recommendation of the entity that provides the cell performance specification or for acquiring data on a cell or stack in order to estimate the performance of a system based on it. Users of this document can selectively execute test items suitable for their purposes from those described in this document. This first edition cancels and replaces IEC TS 62282-7-2 published in 2014. This edition includes the following significant technical changes with respect to IEC TS 622827-2:2014:
- users can substitute selected test methods of this document with equivalent test methods of IEC 62282-8-101 for solid oxide cell (SOC) operation for energy storage purposes, operated in reverse or reversible mode;
- terms and definitions are aligned with the corresponding terms and definitions in IEC 62282-8-101;
- symbols are aligned with the corresponding symbols in IEC 62282-8-101.
- Standard45 pagesEnglish languagesale 15% off
- Standard92 pagesEnglish and French languagesale 15% off
IEC TS 62282-9-102:2021 provides a set of specific rules, requirements and guidelines (i.e. so-called product category rules (PCR) according to ISO 14025 and thus in line with ISO 14040 and ISO 14044) for characterizing the environmental performance of stationary fuel cell combined heat and power (CHP) systems, and alternative systems for residential applications based on life cycle thinking primarily for communication to consumers.
This document covers stationary fuel cell CHP systems and alternative heat (and power) systems for residential applications that primarily serve heating purposes. The systems can be complemented with a hot water storage tank and one or more additional heat generators. The systems are connected to the electricity grid. The environmental performance is characterized in an EPD for each individual heat-related device or CHP generator separately. This document also describes how the environmental performance of a given combination of heat-related devices (including CHP generators) is characterized based on the environmental performance of its individual components. The domestic heat distribution system, district heating, or local infrastructures for fuel supply or for fuel storage are not considered
- Technical specification29 pagesEnglish languagesale 15% off
IEC TS 62282-9-101:2020 provides a streamlined methodology to assess major environmental impacts of stationary fuel cell power systems for residential applications. The fuel cell power systems can be complemented with a supplementary heat generator and/or a thermal storage system such as a hot water tank. The analysis can include the import of electricity from the grid or the export to the grid. The analysed systems are intended to meet the electricity and heat demand of a given household.
This document provides a set of specific rules, requirements and guidelines based on life cycle thinking for the description of relevant environmental impacts of fuel cell power systems that can be complemented with a supplementary heat generator or a thermal storage system. This document also provides guidance on how to communicate these environmental impacts to consumers.
- Technical specification21 pagesEnglish languagesale 15% off
IEC 62282-2-100:2020 provides safety related requirements for construction, operation under normal and abnormal conditions and the testing of fuel cell modules. This document deals with conditions that can yield hazards to persons and cause damage outside the fuel cell modules. Protection against damage inside the fuel cell modules is not addressed in this document, provided it does not lead to hazards outside the module. These requirements can be superseded by other standards for equipment containing fuel cell modules as required for particular applications.
This first edition cancels and replaces IEC 62282-2, published in 2012. This edition includes the following significant technical changes with respect to IEC 622822:2012:
• update of definitions, in particular fuel cell module for normal operation;
• leakage values under normal and abnormal operation have been addressed;
• a delayed ignition test has been included;
• protective measures to limit gas leakage have been included;
• the requirements for insulation between live parts and SELV have been updated;
• the general safety strategy has been modified to reflect the needs for different application standards; the modifications are in line with similar modifications made to IEC 62282-3-100;
• the electrical components clause has been modified to reflect the needs for different application standards; the modifications are in line with similar modifications made to IEC 62282-3-100;
• protective earthing as part of the module or bonding as a measure within the installation has been introduced;
• a dielectric strength test has been completely updated by referring to IEC 62744-1 for voltages up to 1 000 V AC/1 500 V DC;
• a new “pressure drop method” leakage test method has been included;
• a new Annex addressing significant hazards, hazardous situations and events dealt with in this document, and linked to 4.1 (General safety strategy) has been added.
The contents of the corrigendum of November 2023 have been included in this copy.
- Standard90 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.