IEC 61162-450:2011

Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 450: Multiple talkers and multiple listeners - Ethernet interconnection

IEC 61162-450:2011(E) specifies interface requirements and methods of test for high speed communication between shipboard navigation and radiocommunication equipment as well as between such systems and other ship systems that need to communicate with navigation and radio-communication equipment. Is based on the application of an appropriate suite of existing international standards to provide a framework for implementing data transfer between devices on a shipboard Ethernet network. Provides a higher speed and higher capacity alternative to the IEC 61162-1 and IEC 61162-2 standards while retaining these standards' basic data format. Provides a higher data capacity than IEC 61162-3. Specifies an Ethernet based bus type network where any listener may receive messages from any sender.

General Information

• Status: Published
• Publication Date: 30-Mar-2016
• ICS: 47.020.70 - Navigation and control equipment
• Technical Committee: TC 80 - Maritime navigation and radiocommunication equipment and systems
• Drafting Committee: WG 6 - TC 80/WG 6
• Current Stage: DELPUB - Deleted Publication
• Start Date: 13-Jun-2022
• Completion Date: 04-May-2018

Relations

• Replaces: IEC 61162-400:2001 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 400: Multiple talkers and multiple listeners - Ship systems interconnection - Introduction and general principles
• Effective Date: 05-Sep-2023
• Replaces: IEC 61162-401:2001 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 401: Multiple talkers and multiple listeners - Ship systems interconnection - Application profile
• Effective Date: 05-Sep-2023
• Replaces: IEC 61162-410:2001 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 410: Multiple talkers and multiple listeners - Ship systems interconnection - Transport profile requirements and basic transport profile
• Effective Date: 05-Sep-2023
• Replaces: IEC 61162-420:2001 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 420: Multiple talkers and multiple listeners - Ship systems interconnection - Companion standard requirements and basic companion standards
• Effective Date: 05-Sep-2023
• Replaces: IEC 61162-402:2005 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 402: Multiple talkers and multiple listeners - Ship systems interconnection - Documentation and test requirements
• Effective Date: 05-Sep-2023
• Amended By: IEC 61162-450:2011/AMD1:2016 - Amendment 1 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 450: Multiple talkers and multiple listeners - Ethernet interconnection
• Effective Date: 05-Sep-2023
• Revised: IEC 61162-450:2018 - Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 450: Multiple talkers and multiple listeners - Ethernet interconnection
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 61162-450 ®
Edition 1.0 2011-06
INTERNATIONAL
STANDARD
Maritime navigation and radiocommunication equipment and systems – Digital
interfaces –
Part 450: Multiple talkers and multiple listeners – Ethernet interconnection

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,

please contact the address below or your local IEC member National Committee for further information.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
IEC 61162-450 ®
Edition 1.0 2011-06
INTERNATIONAL
STANDARD
Maritime navigation and radiocommunication equipment and systems – Digital
interfaces –
Part 450: Multiple talkers and multiple listeners – Ethernet interconnection

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
XB
ICS 47.020.70 ISBN 978-2-88912-492-3

– 2 – 61162-450  IEC:2011(E)
CONTENTS
FOREWORD . 5

1 Scope . 7

2 Normative references . 7

3 Terms and definitions . 8

4 General network and equipment requirements . 11

4.1 Network topology example . 11

4.2 Basic requirements . 12

4.2.1 Requirements for equipment to be connected to the network . 12
4.2.2 Additional requirements for network infrastructure equipment . 12
4.3 Network function (NF) requirements . 13
4.3.1 General requirements . 13
4.3.2 Maximum data rate requirements . 13
4.3.3 Error logging function . 13
4.4 System function (SF) requirements . 15
4.4.1 General requirements . 15
4.4.2 Assignment of unique system function ID (SFI) . 15
4.4.3 Implementing configurable transmission groups . 15
4.5 Serial to network gateway function (SNGF) requirements . 16
4.5.1 General requirements . 16
4.5.2 Serial line output buffer management . 16
4.5.3 Datagram output requirements . 17
4.6 Other network function (ONF) requirements . 17
5 Low level network requirements. 17
5.1 Electrical and mechanical requirements. 17
5.2 Network protocol requirements . 19
5.3 IP Address assignment for equipment . 19
5.4 Multicast address range . 19
6 Transport layer specification . 19
6.1 General . 19
6.2 UDP messages. 20
6.2.1 UDP multicast protocol . 20
6.2.2 Use of multicast addresses and port numbers. 20

6.2.3 UDP checksum . 21
6.2.4 Datagram size . 21
7 Application layer specification . 22
7.1 Datagram header . 22
7.1.1 Valid header . 22
7.1.2 Error logging. 22
7.2 General IEC 61162-1 sentence transmissions . 22
7.2.1 Application of this protocol . 22
7.2.2 Types of messages for which this protocol can be used . 22
7.2.3 TAG block parameters for sentences transmitted in the datagram . 22
7.2.4 Requirements for processing incoming datagrams . 24
7.2.5 Error logging. 24
7.3 Binary image transfer using UDP multicast . 24
7.3.1 Application of this protocol . 24

61162-450  IEC:2011(E) – 3 –
7.3.2 Binary image structure . 25

7.3.3 Header . 25

7.3.4 Binary image descriptor structure . 27

7.3.5 Binary image data fragment . 28

7.3.6 Sender process for binary image transfer . 28

7.3.7 Receiver process for binary image transfer . 29

7.3.8 Other requirements . 30

7.3.9 Error logging. 31

8 Methods of test and required results . 32

8.1 Test set-up and equipment . 32
8.2 Basic requirements . 32
8.2.1 Equipment to be connected to the network . 32
8.2.2 Network infrastructure equipment . 32
8.3 Network function (NF) . 32
8.3.1 Maximum data rate . 32
8.3.2 Error logging function . 33
8.4 System function (SF) . 33
8.4.1 General . 33
8.4.2 Assignment of unique system function ID (SFI) . 33
8.4.3 Implementing configurable transmission groups . 33
8.5 Serial to network gateway function (SNGF) . 33
8.5.1 General . 33
8.5.2 Serial line output buffer management . 33
8.5.3 Datagram output . 34
8.6 Other network function (ONF) . 34
8.7 Low level network . 34
8.7.1 Electrical and mechanical requirements . 34
8.7.2 Network protocol . 34
8.7.3 IP address assignment for equipment . 35
8.7.4 Multicast address range . 35
8.8 Transport layer . 35
8.9 Application layer . 35
8.9.1 Application . 35
8.9.2 Datagram header . 35
8.9.3 Types of messages . 36

8.9.4 TAG block parameters . 36
8.10 Error logging . 36
8.11 Binary image transfer using UDP multicast . 37
8.11.1 Sender process test . 37
8.11.2 Receiver process test . 38
8.11.3 Image descriptor test . 38
8.11.4 Image transfer error logging . 38
Annex A (normative) Classification of IEC 61162-1 talker identifier mnemonics and
sentences . 39
Annex B (informative) TAG block example . 45
Annex C (normative) Reliable transmission of command-response pair messages . 47
Annex D (informative) Network and system design guidance . 52
Bibliography . 60

– 4 – 61162-450  IEC:2011(E)
Figure 1 – Network topology example . 12

Figure 2 – Ethernet frame example for a SBM from a rate of turn sensor . 20

Figure C.1 – Command response communications . 47

Figure C.2 – State diagram . 49

Figure D.1 – General system design architecture . 52

Figure D.2 – Example of ship-shore communication architecture . 53

Figure D.3 – Security infrastructure . 54

Figure D.4 – Decoupled system .
...

IEC 61162-450 ®
Edition 1.1 2016-03
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Maritime navigation and radiocommunication equipment and systems – Digital
interfaces –
Part 450: Multiple talkers and multiple listeners – Ethernet interconnection

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from

either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]

CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC 61162-450 ®
Edition 1.1 2016-03
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Maritime navigation and radiocommunication equipment and systems – Digital

interfaces –
Part 450: Multiple talkers and multiple listeners – Ethernet interconnection

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 47.020.70 ISBN 978-2-8322-3289-7

IEC 61162-450 ®
Edition 1.1 2016-03
CONSOLIDATED VERSION
REDLINE VERSION
colour
inside
Maritime navigation and radiocommunication equipment and systems – Digital
interfaces –
Part 450: Multiple talkers and multiple listeners – Ethernet interconnection

– 2 – IEC 61162-450:2011+AMD1:2016 CSV
 IEC 2016
CONTENTS
FOREWORD. 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General network and equipment requirements . 11
4.1 Network topology example . 11
4.2 Basic requirements . 12
4.2.1 Requirements for equipment to be connected to the network . 12
4.2.2 Additional requirements for network infrastructure equipment . 12
4.3 Network function (NF) requirements. 13
4.3.1 General requirements . 13
4.3.2 Maximum data rate requirements . 13
4.3.3 Error logging function . 13
4.4 System function (SF) requirements . 15
4.4.1 General requirements . 15
4.4.2 Assignment of unique system function ID (SFI) . 15
4.4.3 Implementing configurable transmission groups . 15
4.5 Serial to network gateway function (SNGF) requirements . 16
4.5.1 General requirements . 16
4.5.2 Serial line output buffer management . 16
4.5.3 Datagram output requirements . 17
4.6 Other network function (ONF) requirements . 17
5 Low level network requirements . 17
5.1 Electrical and mechanical requirements . 17
5.2 Network protocol requirements . 19
5.3 IP Address assignment for equipment . 19
5.4 Multicast address range . 19
6 Transport layer specification . 19
6.1 General . 19
6.2 UDP messages . 20
6.2.1 UDP multicast protocol . 20
6.2.2 Use of multicast addresses and port numbers . 20
6.2.3 UDP checksum . 21
6.2.4 Datagram size . 22
7 Application layer specification . 22
7.1 Datagram header . 22
7.1.1 Valid header . 22
7.1.2 Error logging . 22
7.2 General IEC 61162-1 sentence transmissions . 22
7.2.1 Application of this protocol . 22
7.2.2 Types of messages for which this protocol can be used . 22
7.2.3 TAG block parameters for sentences transmitted in the datagram . 22
7.2.4 Requirements for processing incoming datagrams . 24
7.2.5 Error logging . 24
7.3 Binary image transfer using UDP multicast . 24
7.3.1 Application of this protocol . 24

 IEC 2016
7.3.2 Binary image structure . 25
7.3.3 Header . 25
7.3.4 Binary image descriptor structure . 27
7.3.5 Binary image data fragment . 28
7.3.6 Sender process for binary image transfer . 28
7.3.7 Receiver process for binary image transfer . 30
7.3.8 Other requirements . 31
7.3.9 Error logging . 32
8 Methods of test and required results . 32
8.1 Test set-up and equipment . 32
8.2 Basic requirements . 33
8.2.1 Equipment to be connected to the network . 33
8.2.2 Network infrastructure equipment . 33
8.3 Network function (NF) . 33
8.3.1 Maximum data rate . 33
8.3.2 Error logging function . 33
8.4 System function (SF) . 34
8.4.1 General . 34
8.4.2 Assignment of unique system function ID (SFI) . 34
8.4.3 Implementing configurable transmission groups . 34
8.5 Serial to network gateway function (SNGF) . 34
8.5.1 General . 34
8.5.2 Serial line output buffer management . 34
8.5.3 Datagram output . 35
8.6 Other network function (ONF) . 35
8.7 Low level network . 35
8.7.1 Electrical and mechanical requirements . 35
8.7.2 Network protocol . 35
8.7.3 IP address assignment for equipment . 35
8.7.4 Multicast address range . 36
8.8 Transport layer . 36
8.9 Application layer . 36
8.9.1 Application . 36
8.9.2 Datagram header . 36
8.9.3 Types of messages . 36
8.9.4 TAG block parameters. 37
8.10 Error logging . 37
8.11 Binary image transfer using UDP multicast . 38
8.11.1 Sender process test . 38
8.11.2 Receiver process test . 39
8.11.3 Image descriptor test . 39
8.11.4 Image transfer error logging . 39
Annex A (normative) Classification of IEC 61162-1 talker identifier mnemonics
and sentences . 40
Annex B (informative) TAG block example . 46
Annex D (informative) Network and system design guidance .
...