IEC 61196-10:2022
(Main)Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with fluoropolymer dielectric
Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with fluoropolymer dielectric
IEC 61196-10:2022 specifies the materials and cable construction for semi-rigid coaxial communication cables with fluoropolymer dielectric, IEC type designation, identification, marking and labelling, standard rating and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc. This part of IEC 61196 applies to semi-rigid coaxial communication cables with fluoropolymer dielectric and tubular outer conductor. Semi-rigid coaxial communication cables with fluoropolymer dielectric are widely used in mobile communication systems, microwave test equipment, radar, aerospace and other fields.
This second edition cancels and replaces the first edition published in 2014. This edition includes the following significant technical changes with respect to the previous edition:
a. Title was changed to: Sectional specification for semi-rigid cables with fluoropolymer dielectric b. Dielectric: other fluoropolymer materials (such as FEP, PFA) were added c. Table 1 – Distinguishing number was added d. Table 2 – Rated temperature was added e. 7.4.8, Thermal cycling was deleted f. Annex A: Performance requirements of typical cables was added g. Annex B: Requirements for thermal shock was added
General Information
Relations
Standards Content (Sample)
IEC 61196-10 ®
Edition 2.0 2022-11
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 10: Sectional specification for semi-rigid cables with fluoropolymer
dielectric
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 19 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 61196-10 ®
Edition 2.0 2022-11
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 10: Sectional specification for semi-rigid cables with fluoropolymer
dielectric
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-6019-7
– 2 – IEC 61196-10:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 8
4 Materials and cable construction . 8
4.1 General . 8
4.2 Inner conductor . 8
4.2.1 Conductor material . 8
4.2.2 Conductor construction . 8
4.3 Dielectric . 8
4.4 Outer conductor . 9
4.5 Sheath (when applicable) . 9
5 Type name and identification of cable . 9
5.1 Type . 9
5.2 Variants . 10
5.3 Cable marking . 10
6 Identification, marking and labelling . 10
6.1 Cable identification . 10
6.2 Cable marking . 10
6.3 Labelling . 11
7 Standard rating and characteristics . 11
7.1 Nominal characteristic impedance . 11
7.2 Rated temperature range . 11
7.3 Operating frequency . 11
7.4 Average and peak power . 11
7.5 Bending radius . 11
8 Requirements of finished cables . 11
8.1 General . 11
8.2 Electrical requirements . 12
8.3 Environmental requirements . 13
8.4 Mechanical requirements . 14
8.5 Fire performance requirements (applicable to cables with sheaths) . 15
9 Quality assessment . 15
10 Delivery and storage . 15
Annex A (normative) Performance requirements of typical cables . 16
A.1 Performance requirements . 16
A.2 Attenuation . 16
Annex B (normative) Thermal shock . 18
B.1 General . 18
B.2 Test samples . 18
B.3 Test equipment . 18
B.4 Procedure . 18
B.4.1 Initial measurements . 18
B.4.2 Thermal shock . 18
B.4.3 Final measurements . 19
Annex C (informative) Quality assessment . 20
C.1 General . 20
C.2 Qualification approval and its maintenance . 20
C.2.1 Qualification approval . 20
C.2.2 Capability approval . 20
C.2.3 Quality conformance inspection . 20
Bibliography . 25
Figure 1 – Cable marking . 10
Table 1 – Distinguishing number . 10
Table 2 – Rated temperature . 11
Table 3 – Electrical requirements . 12
Table 4 – Environmental requirements . 13
Table 5 – Mechanical requirements. 14
Table 6 – Fire performance requirements . 15
Table A.1 – Some performance requirements of typical cables . 16
Table A.2 – Maximum attenuation . 17
Table B.1 – Test condition . 19
Table B.2 – Exposure time at temperature extremes . 19
Table C.1 – Qualification inspection . 21
Table C.2 – Quality conformance inspection . 23
– 4 – IEC 61196-10:2022 © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –
Part 10: Sectional specification for semi-rigid cables
with fluoropolymer dielectric
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.