IEC 60297-5-104:2001

Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-104: Subracks and associated plug-in units - Keying

Specifies dimensions which will ensure dimensional interchangeability of subracks and associated plug-in units using the extended feature of a retained keying method added to IEC 60297-3, IEC 60297-4 and IEC 60297-5-107.

General Information

• Status: Replaced
• Publication Date: 23-Jan-2001
• ICS: 31.240 - Mechanical structures for electronic equipment
• Technical Committee: SC 48D - Mechanical structures for electrical and electronic equipment
• Drafting Committee: WG 4 - TC 48/SC 48D/WG 4
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 17-Aug-2004

Relations

• Replaced By: IEC 60297-3-103:2004 - Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-103: Keying and alignment pin
• Effective Date: 05-Sep-2023

Standards Content (Sample)

INTERNATIONAL IEC
STANDARD
60297-5-104
First edition
2001-01
Mechanical structures for electronic equipment –
Dimensions of mechanical structures
of the 482,6 mm (19 in) series –
Part 5-104:
Subracks and associated plug-in units –
Keying
Structures mécaniques pour équipement électronique –
Dimensions des structures mécaniques de la série
de 482,6 mm (19 in) –
Partie 5-104:
Bacs et blocs enfichables associés –
Codage
Reference number
Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the
60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.

Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example,

edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the
base publication incorporating amendment 1 and the base publication incorporating
amendments 1 and 2.
Further information on IEC publications
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology. Information relating to
this publication, including its validity, is available in the IEC Catalogue of
publications (see below) in addition to new editions, amendments and corrigenda.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is also available from the following:
• IEC Web Site (www.iec.ch)
• Catalogue of IEC publications
The on-line catalogue on the IEC web site (www.iec.ch/catlg-e.htm) enables
you to search by a variety of criteria including text searches, technical
committees and date of publication. On-line information is also available on
recently issued publications, withdrawn and replaced publications, as well as
corrigenda.
• IEC Just Published
This summary of recently issued publications (www.iec.ch/JP.htm) is also
available by email. Please contact the Customer Service Centre (see below) for
further information.
• Customer Service Centre
If you have any questions regarding this publication or need further assistance,
please contact the Customer Service Centre:
Email: [e-mail]
Tel: [phone]
Fax: [phone]
INTERNATIONAL IEC
STANDARD
60297-5-104
First edition
2001-01
Mechanical structures for electronic equipment –
Dimensions of mechanical structures
of the 482,6 mm (19 in) series –
Part 5-104:
Subracks and associated plug-in units –
Keying
Structures mécaniques pour équipement électronique –
Dimensions des structures mécaniques de la série
de 482,6 mm (19 in) –
Partie 5-104:
Bacs et blocs enfichables associés –
Codage
 IEC 2001  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: [phone] e-mail: [e-mail] IEC web site http://www.iec.ch
Commission Electrotechnique Internationale
PRICE CODE
P
International Electrotechnical Commission
For price, see current catalogue

– 2 – 60297-5-104  IEC:2001(E)

CONTENTS
Page
FOREWORD . 3

INTRODUCTION .5

Clause
1 Scope and object . 6

2 Normative references . 6

3 Definitions. 7
4 Extended feature added to IEC 60297-3 and IEC 60297-4 . 7
5 General equipment arrangement . 8
6 Detail equipment arrangement. 9
7 Keying of plug-in units in a subrack . 10
7.1 Subrack guide rail dimensions for the keying of box and printed board type
plug-in units with front panels . 10
7.2 Subrack guide rail dimensions for the keying of box and printed board type
plug-in units ≥ 2HP with front panels. 12
7.3 Guide rail dimensions for the keying of board type plug-in units ≥ 3HP. 12
7.4 Programmable key dimensions. 13
7.5 Programming of keys . 14
7.6 Keying chamber inspection dimensions . 15
Figure 1 – General equipment arrangement – Typical 6U subrack with front and/or rear
mounted plug-in units featured with keying. 8
Figure 2 – Design detail equipment arrangement . 9
Figure 3a – Subrack guide rail dimensions for the keying of box and printed board type
plug-in units. 10
Figure 3b – Subrack guide rail mounted key dimension for the keying of box and printed
board type plug-in units .11
Figure 4 – Plug-in unit dimensions for the programmable keying of box and printed
board type plug-in units .11
Figure 5 – Subrack guide rail dimensions for the keying of box and printed board type
plug-in units > 2HP . 12

Figure 6 – Guide rail dimensions for the keying of printed board type
plug-in units > 3HP . 12
Figure 7 – Programmable key dimensions. 13
Figure 8 – Programming of keys . 14
Figure 9 – Front and/or rear subrack and plug-in unit keying chamber inspection
dimensions . 15
Table 1 – Subrack and plug-in unit keying chamber inspection dimensions. 15

60297-5-104 © IEC:2001(E) – 3 –

INTERNATIONAL ELECTROTECHNICAL COMMISSION

___________
MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT –

DIMENSIONS OF MECHANICAL STRUCTURES

OF THE 482,6 mm (19 in) SERIES –

Part 5-104: Subracks and associated plug-in units –

Keying
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60297-5-104 has been prepared by subcommittee 48D: Mechanical
structures for electronic equipment, of IEC technical committee 48: Electromechanical com-
ponents and mechanical structures for electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
48D/242/FDIS 48D/251/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
IEC 60297-5 consists of the following parts under the general title: Mechanical structures for
electronic equipment – Dimensions of mechanical structures of the 482,6 mm (19 in) series:
Part 5-100, Subracks and associated plug-in units – Design overview
Part 5-101, Subracks and associated plug-in units – Injector/extractor handle
Part 5-102, Subracks and associated plug-in units – Electromagnetic shielding provision

– 4 – 60297-5-104  IEC:2001(E)

Part 5-103, Subracks and associated plug-in units – Electrostatic discharge protection

Subracks and associated plug-in units –
Part 5-104, Keying
Part 5-105, Subracks and associated plug-in units – Alignment and/or earth pin

Subracks and associated plug-in units –
Part 5-107, Rear mounted plug-in units

The committee has decided that the contents of this publication will remain unchanged until

2004. At this date, the publication will be

• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

60297-5-104 © IEC:2001(E) – 5 –

INTRODUCTION
This part of IEC 60297 is based on IEC 60297-3 (1984), its Amendment 1 (1992), and

IEC 60297-4 (1995). It contains detail dimensions which ensure dimensional interchangeability

of subracks, plug-in units and keys where board type plug-in units requiring an accessible

method of keying for subrack front and/or rear mounted plug-in units.

This standard applies only to the mechanical structures for electronic equipment practices

according to the IEC 60297 series.

– 6 – 60297-5-104  IEC:2001(E)

MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT –

DIMENSIONS OF MECHANICAL STRUCTURES

OF THE 482,6 mm (19 in) SERIES –

Part 5-104: Subracks and associated plug-in units –

Keying
1 Scope and object
This part of IEC 60297 covers extended features of a retained keying method added to
subracks and plug-in units with front panels according to IEC 60297-3, IEC 60297-4 and
IEC 60297-5-107. By implementing this extended feature to the subracks and plug-in units, a
new subrack and plug-in unit type (incompatible with IEC 60297-3 and IEC 60297-4) is created.
The purpose of this standard is to specify dimensions which will ensure dimensional
interchangeability of subracks and associated plug-in units using the extended feature of a
retained keying method added to IEC 60297-3, IEC 60297-4 and IEC 60297-5-107.
For mechanical and climatic tests refer to IEC 61587-1.
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this part of IEC 60297. For dated references, subsequent amendments
to, or revisions of, any of these publications do not apply. However, parties to agreements
based on this part of IEC 60297 are encouraged to investigate the possibility of applying the
most recent editions of the normative documents indicated below. For undated references, the
latest edition of the normative document referred to applies. Members of IEC and ISO maintain
registers of currently valid International Standards.
IEC 60297-3, Dimensions of mechanical structures of the 482,6 mm (19 in) series – Part 3:
Subracks and associated plug-in units
IEC 60297-4, Mechanical structures for electronic equipment – Dimensions of mechanical
structures of the 482,6 mm (19 in) series – Part 4: Subracks and associated plug-in units –
Additional dimensions
IEC 60297-5-100, Mechanical structures for electronic equipment – Dimensions of mechanical
structures of the 482,6 mm (19 in) series – Part 5-100: Subracks and associated plug-in units –
Design overview
IEC 60297-5-107, Mechanical structures for electronic equipment – Dimensions of mechanical
structures of the 482,6 mm (19 in) series – Part 5-107: Subracks and associated plug-in units –
Rear mounted plug-in units
IEC 60917-1, Modular order for the development of mechanical structures for electronic
equipment practices – Part 1: Generic standard
IEC 61587-1, Mechanical structures for electronic equipment – Tests for IEC 60917 and
IEC 60297 – Part 1: Climatic, me
...