IEC TS 60034-27-5:2021 provides an off-line measurement method of the partial discharge inception and extinction voltage on winding insulation under repetitive impulse voltage. This document is relevant to rotating machines supplied by a voltage source converter.

  • Technical specification
    42 pages
    English language
    sale 15% off

The scope of this document is to define requirements for the shore supply system for auxiliaries and pre-conditioning and the related intermateable connector pairs.
Shore supplies to move the rolling stock are outside the scope of this document.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62966-2:2020 is dedicated to aisle containment techniques for information technology (IT) equipment typically used in data centres, describes the quantification of its air tightness, in particular the air loss ratio that describes the content of the volumetric flow not used for cooling the IT equipment. This ratio provides an index of efficiency, being inversely proportional to efficiency (the lower this ratio, the higher the efficiency). This document provides methods to measure an aisle containment air leakage rate and defines a classification system for aisle containment leakage.
This document defines:
- the measurement of the air leakage of the individual components of an aisle containment;
- a method for calculating the air leakage of an aisle containment based on its individual components;
- a method for calculating the air leakage rate of an aisle containment in relation to the utilised IT equipment;
- a classification system for aisle containment leakage.

  • Standard
    50 pages
    English and French language
    sale 15% off

IEC TS 62196-3-1:2020(E) applies to accessories and cable assemblies with the same configuration as specified in IEC 62196-3:2014 with rated operating voltage not exceeding 1 500 V DC and a rated current not exceeding 500 A that employ
- thermal sensing, or
- thermal transport and thermal sensing with the system architecture described in 4.101.
These accessories and cable assemblies are intended to be used in conductive charging systems for circuits specified in IEC 61851-23.
NOTE Edition 2 of IEC 61851-23 is under development.
The accessories covered by this document are intended to be used in charging mode 4 according to IEC 61851-1. These accessories are intended to be connected to cables according to the IEC 62893 series for DC cables.

  • Technical specification
    62 pages
    English language
    sale 15% off

This part of 60309 applies to a single type of plug, socket-outlet, ship connector and ship
inlet, hereinafter referred to as accessories, intended to connect ships to dedicated shore
supply systems described in IEC/IEEE 80005-3.
This part of IEC 60309 applies to three-phase accessories with an earth contact and with four
pilot contacts.
NOTE 1 In the following countries the term “ground” is used instead of “earth": US.
These accessories have a maximum rated current of 350 A and a maximum rated operating
voltage not exceeding 690 V 50/60 Hz.
NOTE 2 The various operating currents, voltages and frequencies required for various types of ship are set by the
shore supply system described in IEC/IEEE 80005-3.
These accessories are intended to be installed and operated by instructed persons
(IEC 60050-195:1998, Amendment 1:2001, 195-04-02) or skilled persons
(IEC 60050-195:1998, Amendment 1:2001, 195-04-01) only.
This standard applies to accessories for primary use outdoors in a seawater environment
when the ambient temperature is normally within the range of −25 °C to +40 °C.
NOTE 3 In some countries, other ambient temperatures may prevail and may need to be taken into account.
These accessories are intended to be connected to cables of copper or copper alloy only.
Socket-outlets or ship inlets incorporated in or fixed to electrical equipment which is part of
the shore connection system are within the scope of this standard.
In locations where special conditions prevail, for example where explosions are liable to
occur, additional requirements may be necessary.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to two-wire, up to five-wire installation couplers, including earth, if
provided, with a rated voltage up to and including 500 V AC or DC and a rated connecting
capacity up to and including 10 mm2 for permanent connection in electrical installations.
Installation couplers with additional contacts for voltages other than mains voltages are
outside the scope of this document.
An installation coupler consists of an installation female connector and an installation male
connector for permanent connection not intended to be engaged or disengaged under load
nor to be engaged or disengaged other than during first installation or during reconfiguration
or maintenance of the wiring system in which installation couplers have been installed. This
means that installation couplers are only intended for infrequent use.
Installation couplers are not suitable for use in place of socket-outlet systems. Installation
couplers are not suitable for use in place of devices for connecting luminaires (DCLs)
according to IEC 61995 (all parts) or in place of luminaire supporting couplers (LSCs).
Installation couplers complying with this document are suitable for use at ambient
temperatures not normally exceeding +40 °C, but their average over a period does not exceed
+35 °C, with a lower limit of the ambient air temperature of −5 °C, either for indoor or outdoor
use.
NOTE 1 Additional tests for use in cold climates are under consideration.
NOTE 2 For other temperatures, necessary information can be given in the manufacturer's installation
instructions.
In locations where special conditions prevail, as in ships, vehicles and the like and in
hazardous locations, for example where explosions are liable to occur, special constructions
can be required.
NOTE 3 Installation couplers are intended to be installed by instructed or skilled persons.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63057:2020 specifies safety tests and requirements for secondary lithium batteries permanently installed in road vehicles not for the propulsion. Replacement secondary batteries permanently installed in road vehicles not for propulsion are covered by this document.
The following are typical applications that utilize the batteries under the scope of this document: a power source for the starting of internal combustion engines, lighting, on-board auxiliary equipment, and energy absorption for regeneration from braking.
This document applies to batteries with a maximum voltage less than or equal to 60 V DC.
The batteries primarily used for propulsion of electric vehicles (EVs), including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), and plug-in hybrid electric vehicles (PHEVs) are not covered by this document.

  • Standard
    42 pages
    English and French language
    sale 15% off

IEC 60309-5:2017 applies to a single type of plug, socket-outlet, ship connector and ship inlet, hereinafter referred to as accessories, intended to connect ships to dedicated shore supply systems described in IEC/IEEE 80005-3. This part of IEC 60309 applies to three-phase accessories with an earth contact and with four pilot contacts. This publication is to be read in conjunction with IEC 60309-1:2012.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and
two poles with earth contact and for the connection of electrical devices for household and
similar onto the mains supply.
This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or
incorporated in appliances.
The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A.
Appliance couplers complying with this part of lEC 60320 are suitable for normal use at
ambient temperatures not normally exceeding +40 °C, but their average over a period of 24 h
does not exceed +35 °C, with a lower limit of the ambient air temperature of –5 °C.
Appliance couplers are not suitable for
– use in place of plug and socket-outlet systems according to IEC 60884-1.
– use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or
luminaire supporting couplers (LSCs).
NOTE Requirements for d.c. are under consideration.

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and
two poles with earth contact and for the connection of electrical devices for household and
similar onto the mains supply.
This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or
incorporated in appliances.
The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A.
Appliance couplers complying with this part of lEC 60320 are suitable for normal use at
ambient temperatures not normally exceeding +40 °C, but their average over a period of 24 h
does not exceed +35 °C, with a lower limit of the ambient air temperature of –5 °C.
Appliance couplers are not suitable for
– use in place of plug and socket-outlet systems according to IEC 60884-1.
– use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or
luminaire supporting couplers (LSCs).
NOTE Requirements for d.c. are under consideration.

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

This document applies in connection with EN 15869-1 for the supply of berthed inland navigation vessels with electrical energy.
This document specifies additional requirements for the on-shore unit of the electrical shore connection.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62613-1:2019 applies to accessories with
- three phases and earth with pilot contacts,
- one pole for neutral.
These accessories have rated currents not exceeding 500 A and rated operating voltages not exceeding 12 kV 50/60 Hz.
This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) extension of the scope to an unlimited number of pilot contacts (previously limited to 3);
b) update of the Figures and deletion of their embedded texts;
c) insertion of tables of keys whenever required by the Figures.

  • Standard
    106 pages
    English and French language
    sale 15% off

Standard določa dimenzijske zahteve za vtiče in vtičnice za hišno in podobno uporabo.
Ta standard se nanaša samo na vtiče z ozemljitvenim kontaktom ali brez njega in fiksne ali prenosne
vtičnice z ozemljitvenim kontaktom z naznačeno izmenično napetostjo, večjo od 50 V in manjšo od 250
V, ter z naznačenim tokom, ki ne presega 16 A, namenjene za hišno in podobno uporabo v zgradbah in
zunaj njih v enofaznem omrežju.
Ta standard velja tudi za vtiče, ki so del konfekcioniranih kablov, za vtiče in prenosne vtičnice, ki so del
kabelskih podaljškov, ter za vtiče in vtičnice, ki so del aparata in niso definirani v standardu za ta aparat.
Vtiči in vtičnice, ki ustrezajo temu standardu, so primerni za uporabo pri temperaturah okolja, ki navadno
ne presegajo 25 °C, občasno pa dosežejo 35 °C.
Ta standard ne velja za:
– vtiče, vtičnice in spojke za industrijske namene,
– aparatne spojke,
– vtiče, fiksne in prenosne vtičnice za male napetosti (ELV).
Na krajih, kjer prevladujejo posebne okoliščine, kot so npr. ladje, vozila in podobno, ter na nevarnih
krajih, kjer lahko npr. pride do eksplozije, se lahko zahtevajo posebne konstrukcije.

  • Standard
    35 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day

IEC 60320-2-4:2018 is now available as IEC 60320-2-4:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60320-2-4:2018 is applicable to two-pole appliance couplers for alternating current only, with or without earthing contact, with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A, for household and similar general purposes and intended for incorporation or integration within electric appliances or other electric equipment of multi‑part construction for 50 Hz or 60 Hz supply which depend on the weight of the appliance to ensure correct engagement. This second edition cancels and replaces the first edition published in 2005 and Amendment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- IEC 60320-2-4 is aligned with IEC 60320-1:2015.
- IEC 60320-2-4 is aligned with IEC 60335-1 and IEC 60335-2-15. IEC 60320-2-4 appliance couplers are incorporated into appliances designed and manufactured to these standards. To this end, particular attention is drawn to 14.2 and Clause 20.
- It also now proposes that appliance couplers with auxiliary contacts be considered.

  • Standard
    71 pages
    English and French language
    sale 15% off

IEC 60320-2-3:2018 is now available as IEC 60320-2-3:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60320-1:2018 applies with the following addition: This document applies to appliance couplers with a degree of protection against ingress of water higher than IPX0. This second edition cancels and replaces the first edition published in 1998 and Amendment 1:2004. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Aligned with IEC 60320-1:2015.
- The scope is extended to cover current ratings up to and including 16 A.
- The scope is extended to cover Class I appliance couplers.
- The scope is extended to cover appliance couplers for hot and very hot conditions.
- Added classification regarding the use of retaining devices.
- Added classification for indoor and outdoor use.

  • Standard
    36 pages
    English and French language
    sale 15% off

The purpose of the IEC/ISO/IEEE 80005-1 is to define requirements that allow compliant ships to connect to compliant high-voltage shore power supplies through a compatible shore-to-ship connection.
IEC 62613 has been written to address the needs of 80005-1 in terms of plugs, socket-outlets, ship connectors and ship inlets (herein referred to as "accessories") to deliver electrical power to ships in ports.
IEC 62613 applies to accessories with
-   three phases and earth with pilot contacts,
-   one single pole for neutral.
These accessories have rated currents not exceeding 500 A and rated operating voltages not exceeding 12 kV 50/60 Hz.
These accessories are primarily intended for use outdoors, in a seawater environment, for the shore supply of ships (ship-to-shore connection), in an ambient temperature within the range of  25 °C to +45 °C.
NOTE 1: In some countries, other ambient temperatures may prevail and may need to be taken into account.
These accessories are not intended for use in hazardous areas. In such locations where special conditions prevail, additional requirements may be necessary.
Part 2 of IEC 62613 contains the standard sheets for different configurations of (shore) socket-outlets, (shore) plugs, ship connectors and ship inlets, up to 12 kV, 500 A, 50/60 Hz and with pilot/auxiliary contacts.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The purpose of the IEC/ISO/IEEE 80005-1 is to define requirements that allow compliant ships to connect to compliant high-voltage shore power supplies through a compatible shore-to-ship connection.
IEC 62613 has been written to address the needs of 80005-1 in terms of plugs, socket-outlets, ship connectors and ship inlets (herein referred to as "accessories") to deliver electrical power to ships in ports.
IEC 62613 applies to accessories with
-   three phases and earth with pilot contacts,
-   one single pole for neutral.
These accessories have rated currents not exceeding 500 A and rated operating voltages not exceeding 12 kV 50/60 Hz.
These accessories are primarily intended for use outdoors, in a seawater environment, for the shore supply of ships (ship-to-shore connection), in an ambient temperature within the range of  25 °C to +45 °C.
NOTE 1: In some countries, other ambient temperatures may prevail and may need to be taken into account.
These accessories are not intended for use in hazardous areas. In such locations where special conditions prevail, additional requirements may be necessary.

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The purpose of the IEC/ISO/IEEE 80005-1 is to define requirements that allow compliant ships to connect to compliant high-voltage shore power supplies through a compatible shore-to-ship connection. IEC 62613 has been written to address the needs of 80005-1 in terms of plugs, socket-outlets, ship connectors and ship inlets (herein referred to as "accessories") to deliver electrical power to ships in ports. IEC 62613 applies to accessories with - three phases and earth with pilot contacts, - one single pole for neutral. These accessories have rated currents not exceeding 500 A and rated operating voltages not exceeding 12 kV 50/60 Hz. These accessories are primarily intended for use outdoors, in a seawater environment, for the shore supply of ships (ship-to-shore connection), in an ambient temperature within the range of 25 °C to +45 °C. NOTE 1: In some countries, other ambient temperatures may prevail and may need to be taken into account. These accessories are not intended for use in hazardous areas. In such locations where special conditions prevail, additional requirements may be necessary. Part 2 of IEC 62613 contains the standard sheets for different configurations of (shore) socket-outlets, (shore) plugs, ship connectors and ship inlets, up to 12 kV, 500 A, 50/60 Hz and with pilot/auxiliary contacts.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The purpose of the IEC/ISO/IEEE 80005-1 is to define requirements that allow compliant ships to connect to compliant high-voltage shore power supplies through a compatible shore-to-ship connection. IEC 62613 has been written to address the needs of 80005-1 in terms of plugs, socket-outlets, ship connectors and ship inlets (herein referred to as "accessories") to deliver electrical power to ships in ports. IEC 62613 applies to accessories with - three phases and earth with pilot contacts, - one single pole for neutral. These accessories have rated currents not exceeding 500 A and rated operating voltages not exceeding 12 kV 50/60 Hz. These accessories are primarily intended for use outdoors, in a seawater environment, for the shore supply of ships (ship-to-shore connection), in an ambient temperature within the range of 25 °C to +45 °C. NOTE 1: In some countries, other ambient temperatures may prevail and may need to be taken into account. These accessories are not intended for use in hazardous areas. In such locations where special conditions prevail, additional requirements may be necessary. Part 1 of IEC 62613 contains the general requirements;

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60799:2018 is also available as IEC 60799:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60799:2018 specifies requirements for cord sets and interconnection cord sets for household and similar general purpose equipment. It does not apply to cord sets for industrial purposes (with plugs and connectors according to IEC 60309) nor to cord extension sets. This third edition cancels and replaces the second edition published in 1998. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- alignment with IEC 60320-1:2015;
- extension to include appliance couplers in accordance with IEC 60320-2-3:- (Under preparation. Stage at the time of publication: IEC/FDIS 60320-2-3:2018)

  • Standard
    22 pages
    English and French language
    sale 15% off
  • Technical report
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60320-2-1:2018 is applicable to special purpose appliance couplers for household sewing machines. These sewing machine couplers are for alternating current only and have a rated voltage not exceeding 250 V and a rated current not exceeding 2,5 A.
This third edition cancels and replaces the second edition published in 2000. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- Aligned with IEC 60320-1:2015.
This Part 2-1 is to be used in conjunction with IEC 60320-1: Appliance couplers for household and similar general purposes – Part 1: General requirements. It was established on the basis of the third edition of that standard (2015).

  • Standard
    32 pages
    English and French language
    sale 15% off

This part of IEC 62196 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories.
They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles.
This part of IEC 62196 covers the basic interface accessories for vehicle supply as specified in IEC 62196-1, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010.
NOTE 1 Electric road vehicles (EV) implies all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from RESS.
These accessories are intended to be used for circuits specified in IEC 61851-1:2010 which operate at different voltages and frequencies and which may include extra-low voltage (ELV) and communication signals.
These accessories may be used for bidirectional power transfer (under consideration). This standard applies to accessories to be used in an ambient temperature between –30 °C and +50 °C.
NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO.
NOTE 3 In the following country, –35 °C applies: SE.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
Vehicle inlet and vehicle connector to this standard are intended to be used for charging in modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are intended to be used for charging mode 3 only, case A and B.
The modes and permissible connections are specified in IEC 62196-1:2014.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO/TR 80002-2:2017(E) applies to any software used in device design, testing, component acceptance, manufacturing, labelling, packaging, distribution and complaint handling or to automate any other aspect of a medical device quality system as described in ISO 13485.
ISO/TR 80002-2:2017 applies to
- software used in the quality management system,
- software used in production and service provision, and
- software used for the monitoring and measurement of requirements.
It does not apply to
- software used as a component, part or accessory of a medical device, or
- software that is itself a medical device.

  • Technical report
    84 pages
    English language
    sale 15% off

IEC 60884-2-5:2017 applies to adaptors for a.c. only with or without earthing contact, with a rated voltage greater than 50 V but not exceeding 440 V and a rated current not exceeding 32 A, intended for household and similar purposes, either indoors or outdoors.
This document also applies to travel adaptors (see Annex AA). For travel adaptors the scope is limited to a voltage rating greater than 50 V but not exceeding 250 V and to a current rating not exceeding 20 A.
Travel adaptors allowing the simultaneous connection of two or more plugs are not covered by this document.
This second edition cancels and replaces the first edition published in 1995. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) a general alignment with IEC 60884-1:2002, Amendment 1:2006 and Amendment 2:2013;
b) new and modified definitions;
c) requirements for travel adaptors, for adaptors with additional functions and for adaptors with a cable outlet;
d) requirements for adaptors with incorporated overcurrent protective devices;
e) requirement to warn against inserting an adaptor into another adaptor;
f) new requirements for the construction and shape of the adaptors.

  • Standard
    86 pages
    English and French language
    sale 15% off

IEC 62657-2:2017,
- specifies the fundamental assumptions, concepts, parameters, and procedures for wireless communication coexistence;
- specifies coexistence parameters and how they are used in an application requiring wireless coexistence;
- provides guidelines, requirements, and best practices for wireless communication's availability and performance in an industrial automation plant; it covers the life‑cycle of wireless communication coexistence;
- helps the work of all persons involved with the relevant responsibilities to cope with the critical aspects at each phase of life-cycle of the wireless communication coexistence management in an industrial automation plant. Life-cycle aspects include: planning, design, installation, implementation, operation, maintenance, administration and training;
- provides a common point of reference for wireless communication coexistence for industrial automation sites as a homogeneous guideline to help the users assess and gauge their plant efforts;
- deals with the operational aspects of wireless communication coexistence regarding both the static human/tool-organization and the dynamic network self-organization.
This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision.
This second edition includes the following significant technical changes with respect to the previous edition:
a) update of the normative references, terms, definitions, symbols and abbreviations;
b) addition of terms;
c) checking of the life-cycle terms of this document versus the terms used in IEC 62890: and addition of explanations;
d) addition and modification of text to make the text more readable;
e) alignment of some definitions and specifications of coexistence parameters in order to facilitate their future inclusion in the IEC Common Data Dictionary (IEC CDD) maintained by the IEC.

  • Standard
    188 pages
    English and French language
    sale 15% off
  • Standard
    27 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day

IEC 62196-2:2016 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This second edition cancels and replaces the first edition published in 2011 and constitutes a technical revision. This second edition includes the following significant technical changes with respect to the previous edition. a) Standard sheets for configurations type 2 and type 3 have been updated. b) Configuration type 2 is now available with optional shutter. This publication is to be read in conjunction with IEC 62196-1:2014.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TS 63066:2017(E) applies to docking connectors (hereinafter referred to as accessories) incorporated in or fixed to electrical equipment, intended to connect removable energy storage units to a dedicated electric power conversion unit, to an energy consuming unit or to another energy storage unit.

  • Technical specification
    50 pages
    English language
    sale 15% off

This European Standard specifies requirements relating to electrical installations for the supply of electrical power (three-phase AC - 400 V, 50 Hz and with a rated current of at least 250 A) to vessels in port.
Annex A stipulates general and safety requirements relating to the shore-based section of the electrical shore connection.
Annex B stipulates general and safety requirements relating to the shore-based connecting cables and to the on-board section of the electrical shore connection.
Annex C contains information concerning the dimensioning of shore-based connecting cables.
The requirements according to the HD 60364 and HD 384 series of standards generally apply to shore-based low-voltage equipment.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60309-5:2017 applies to a single type of plug, socket-outlet, ship connector and ship inlet, hereinafter referred to as accessories, intended to connect ships to dedicated shore supply systems described in IEC/IEEE 80005-3.
This part of IEC 60309 applies to three-phase accessories with an earth contact and with four pilot contacts.
This publication is to be read in conjunction with IEC 60309-1:2012.

  • Standard
    32 pages
    English and French language
    sale 15% off

IEC TS 62735-2: 2016(E) applies to plugs and fixed socket-outlets for class I equipment with two active contacts plus an earthing contact, a rated power of 5,2 kW and a rated voltage range from 294 V to 400 V d.c. They are intended to power d.c. information and communication technology equipment only. The 2,6 kW system complying with Part 1 is safely compatible with the system complying with this part as it is possible to insert the 2,6 kW plug in the 5,2 kW socket-outlet but it is not possible to insert the 5,2 kW plug into the 2,6 kW socket-outlet.
This publication is to be read in conjunction with IEC TS 62735-1:2015

  • Technical specification
    21 pages
    English language
    sale 15% off

IEC 62613-2:2016 contains standard sheets for different configurations of (shore) socket-outlets, (shore) plugs, ship connectors and ship inlets, hereinafter referred to as accessories, up to 12 kV, 500 A, 50/60 Hz and with up to seven pilot/auxiliary contacts. General requirements are given in IEC 62613-1. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) addition of configuration I: 7,2 kV 350 A three-phase accessories with three IP0 pilot contacts;
b) addition of configuration J: 12 kV 500 A three-phase accessories with seven pilot contacts;
c) improvement of drawings in standard sheets and addition of missing dimensions.

  • Standard
    96 pages
    English and French language
    sale 15% off

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and
two poles with earth contact and for the connection of electrical devices for household and
similar onto the mains supply.
This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or
incorporated in appliances.
The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A.
Appliance couplers complying with this part of lEC 60320 are suitable for normal use at
ambient temperatures not normally exceeding +40 °C, but their average over a period of 24 h
does not exceed +35 °C, with a lower limit of the ambient air temperature of –5 °C.
Appliance couplers are not suitable for
– use in place of plug and socket-outlet systems according to IEC 60884-1.
– use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or
luminaire supporting couplers (LSCs).
NOTE Requirements for d.c. are under consideration.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62196-2:2016 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This second edition cancels and replaces the first edition published in 2011 and constitutes a technical revision. This second edition includes the following significant technical changes with respect to the previous edition.
a) Standard sheets for configurations type 2 and type 3 have been updated.
b) Configuration type 2 is now available with optional shutter.
This publication is to be read in conjunction with IEC 62196-1:2014.

  • Standard
    122 pages
    English and French language
    sale 15% off

IEC TR 60083:2015 The object of this technical report is to give general information about the systems of plugs and socket-outlets for household and similar purposes which are used in the IEC countries. The report only contains National Systems which are commonly used in homes and offices. It is therefore limited to systems for a.c. with a rated voltage above 50 V but not exceeding 440 V, intended for household and similar purposes, either indoors or outdoors. The report only contains systems for which standard sheets have been published in a National Standard, which may be a National Standard of the country itself or any other IEC member country. The seventh edition cancels and replaces the sixth edition published in 2009 and constitutes a technical revision. It includes some replacements of the sheets concerning the following countries: AT, CA, DK, FR, DE, IT, JP, NL, NZ, PT, SA, SG, ES and CH. New sheets for HU, RO and TH have been added to those of the previous edition.

  • Technical report
    421 pages
    English and French language
    sale 15% off

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and
two poles with earth contact and for the connection of electrical devices for household and
similar onto the mains supply.
This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or
incorporated in appliances.
The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A.
Appliance couplers complying with this part of lEC 60320 are suitable for normal use at
ambient temperatures not normally exceeding +40 °C, but their average over a period of 24 h
does not exceed +35 °C, with a lower limit of the ambient air temperature of –5 °C.
Appliance couplers are not suitable for
– use in place of plug and socket-outlet systems according to IEC 60884-1.
– use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or
luminaire supporting couplers (LSCs).
NOTE Requirements for d.c. are under consideration.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

lEC 60320-1:2015(E) sets the general requirements for appliance couplers for two poles and two poles with earth contact and for the connection of electrical devices for household and similar onto the mains supply. This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or incorporated in appliances. The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A. This third edition cancels and replaces the second edition published in 2001 and Amendment 1:2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Standard sheets moved from IEC 60320-1 to IEC 60320-3. b) Clarification of requirements for non-standardized appliance couplers.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TS 62735-1:2015(E) applies to plugs and fixed socket-outlets for class I equipment with two active contacts plus an earthing contact, a rated power of 2,6 kW and a rated voltage range from 294 V to 400 V d.c. They are intended to power d.c. information and communication technology equipment only, products according to IEC 60950.

  • Technical specification
    121 pages
    English language
    sale 15% off

lEC 60320-1:2015 sets the general requirements for appliance couplers for two poles and two poles with earth contact and for the connection of electrical devices for household and similar onto the mains supply. This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or incorporated in appliances. The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A. This third edition cancels and replaces the second edition published in 2001 and Amendment 1:2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Standard sheets moved from IEC 60320-1 to IEC 60320-3.
b) Clarification of requirements for non-standardized appliance couplers.
This bilingual version (2016-11) corresponds to the monolingual English version, published in 2015-06. The French version of this standard has not been voted upon.
The contents of the corrigenda of January 2016 and May 2019 have been included in this copy.

  • Standard
    125 pages
    English and French language
    sale 15% off

This part of IEC 62196 is applicable to vehicle couplers with pins and contact-tubes of
standardized configuration, herein also referred to as “accessories”, intended for use in
electric vehicle conductive charging systems which incorporate control means, with rated
operating voltage up to 1 500 V d.c. and rated current up to 250 A, and 1 000 V a.c. and rated
current up to 250 A.
This part of IEC 62196 applies to high power d.c. interfaces and combined a.c./d.c. interfaces
of vehicle couplers specified in IEC 62196-1:2014, and intended for use in conductive
charging systems for circuits specified in IEC 61851-1:2010, and IEC 61851-23:2014.
The d.c. vehicle connectors covered by this part of the standard are used only in charging
mode 4, according to Case C in Clause 6.2 of IEC 61851-1:2010, Figure 3 in Clause 6.3.1 of
IEC 61851-1:2010 and IEC 62196-2:2011.
The d.c. vehicle inlets covered by this part of the standard are used only in charging mode 4,
according to Case C in Clause 6.2 of IEC 61851-1:2010, Figure 3 in Clause 6.3.1 of
IEC 61851-1:2010.
These vehicle couplers are intended to be used for circuits similar to those specified in
IEC 61851-23 which operate at different voltages and which may include ELV and
communication signals.
This part of IEC 62196 applies to the vehicle couplers to be used in an ambient temperature
of between –30 °C and +50 °C.
NOTE 1 In some countries, other requirements may apply.
NOTE 2 In the following country, –35 °C applies: SE.
These vehicle couplers are intended to be connected only to cables with copper or copperalloy
conductors.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 62196 is applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets
and cable assemblies for electric vehicles, herein referred to as “accessories”, intended for
use in conductive charging systems which incorporate control means, with a rated operating
voltage not exceeding
– 690 V a.c. 50 Hz to 60 Hz, at a rated current not exceeding 250 A,
– 1 500 V d.c. at a rated current not exceeding 400 A.
These accessories are intended to be installed by instructed persons (IEC 60050-195:1998,
IEC 60050-195/AMD1:2001, 195-04-02) or skilled persons (IEC 60050-195:1998, IEC 60050-
195/AMD1:2001, 195-04-01) only.
These accessories and cable assemblies are intended to be used for circuits specified in
IEC 61851-1 which operate at different voltages and frequencies and which may include
extra-low voltage and communication signals.
These accessories and cable assemblies are to be used at an ambient temperature between
–30 °C and +50 °C.
NOTE 1 In some countries, other requirements may apply.
NOTE 2 the following countries, –35 °C applies: SE.
These accessories are intended to be connected only to cables with copper or copper-alloy
conductors.
The accessories covered by this part of IEC 62196 are for use in certain modes of charging
electric vehicles. These modes are defined in IEC 61851-1. These definitions and a
description of the types of connection (cases A, B and C), are described in IEC 61851-1:2010,
6.2 and 6.3.1.
NOTE 3 In the following countries, mode 1 will not be allowed: UK, US, CA, SG.
This part of IEC 62196 does not apply to those standardised accessories used in charging
systems where the use of such accessories constructed to the requirements of other
standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be
used for those situations (mode and case) identified in IEC 61851-1.
This part of IEC 62196 may be used as a guide for accessories with a lesser number of
contacts and lower ratings for use with light duty vehicles.

  • Standard
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of the lEC 60320 sets the dimensions for appliance couplers for two poles and two
poles with earth contact
– for the connection of electrical devices for household and similar onto the mains supply
and
– for the interconnection of the electrical supply to appliance or equipment
– and dimensions for gauges.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day

lEC 60320-3:2014 sets the dimensions for appliance couplers for two poles and two poles with earth contact: - for the connection of electrical devices for household and similar onto the mains supply and - for the interconnection of the electrical supply to appliance or equipment - and dimensions for gauges.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62196-1:2014 is applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets and cable assemblies for electric vehicles, herein referred to as "accessories", intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding: - 690 V a.c. 50 Hz to 60 Hz, at a rated current not exceeding 250 A; - 1 500 V d.c. at a rated current not exceeding 400 A. This third edition cancels and replaces the second edition published in 2011 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of a preferred operating voltage of 1 000 V d.c.; b) addition of a preferred rated current of 80 A d.c.; c) addition of a provision for a combined interface a.c./d.c.; d) description of d.c. configurations (previously under consideration); e) addition of requirements pertaining to the locking mechanism, the interlock and the latching device; f) addition of a test for accessories not suitable for making and breaking an electrical circuit under load; g) addition of requirements and tests for insulated end caps.

  • Standard
    91 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62196-3:2014 is applicable to vehicle couplers with pins and contact-tubes of standardized configuration, herein also referred to as "accessories", intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage up to 1 500 V d.c. and rated current up to 250 A, and 1 000 V a.c. and rated current up to 250 A. This part of IEC 62196 applies to high power d.c. interfaces and combined a.c./d.c. interfaces of vehicle couplers specified in IEC 62196-1:2014, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010, and IEC 61851-23:2014. This publication is to be read in conjunction with IEC 62196-1:2011.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

lEC 60320-3:2014 sets the dimensions for appliance couplers for two poles and two poles with earth contact:
- for the connection of electrical devices for household and similar onto the mains supply and
- for the interconnection of the electrical supply to appliance or equipment
- and dimensions for gauges.
This publication is to be read in conjunction with IEC 60320-1:2007.

  • Standard
    161 pages
    English and French language
    sale 15% off

Applies to plugs and socket-outlets, cable couplers and appliance couplers, with a rated operating voltage not exceeding 690 V d.c. or a.c. and 500 Hz a.c. and a rated current not exceeding 250 A, primarily intended for industrial use, either indoors or outdoors. The list of preferred ratings is not intended to exclude other ratings, requirements for which are under consideration. This European Standard applies to Series I products only. Series II products are not allowed and not suitable for use in Europe: reference and requirements for Series II products are reported in this standard for information only and shall be ignored. This European Standard applies to products intended to be used with cables with metric sizes (mm2) only. Reference and requirements to AWG and MCM cables are present in the relevant IEC publication and they are reported in this standard for information only. See Annex ZB for a list of references to Series II and/or AWG/MCM cable which are excluded from this standard.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day