IEC 61753-082-02:2024
(Main)Fibre optic interconnecting devices and passive components - Performance standard - Part 082-02: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM devices for category C - Indoor controlled environment
Fibre optic interconnecting devices and passive components - Performance standard - Part 082-02: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM devices for category C - Indoor controlled environment
IEC 61753-082-02:2024 contains the minimum initial test, measurement requirements and severities which a fibre optic 1,31/1,55 µm wide wavelength division multiplexing (WWDM) device satisfies in order to be categorised as meeting the requirements of category C (indoor controlled environment), as defined in IEC 61753-1:2018, Annex A. WWDM is defined in IEC 62074-1. This first edition cancels and replaces the first edition of IEC 61753-082-2 published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) change of test conditions harmonizing with IEC 61753-1.
Dispositifs d’interconnexion et composants passifs fibroniques - Norme de performance - Partie 082-02: Dispositifs WWDM 1,31 µm/1,55 µm fibroniques équipées d'une fibre amorce pour la catégorie C - Environnement intérieur contrôlé
IEC 61753-082-02: 2024 contient les exigences minimales initiales d’essai et de mesure, ainsi que les sévérités auxquelles un dispositif fibronique de multiplexage par répartition en longueur d’onde large (WWDM, Wide Wavelength Division Multiplexing) 1,31 µm/1,55 µm est tenu de satisfaire pour être classé comme étant conforme aux exigences de la catégorie C (environnement intérieur contrôlé), selon la définition donnée dans l’IEC 61753‑1:2018, Annexe A. Le protocole WWDM est défini dans l’IEC 62074-1. Cette première édition annule et remplace la première édition de l’IEC 61753-082-2 parue en 2008 et constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) modification des conditions d'essai pour harmonisation avec l’IEC 61753-1.
General Information
Relations
Standards Content (Sample)
IEC 61753-082-02 ®
Edition 1.0 2024-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Performance
standard –
Part 082-02: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM devices for
category C – Indoor controlled environment
Dispositifs d’interconnexion et composants passifs fibroniques – Norme de
performance –
Partie 082-02: Dispositifs WWDM 1,31 µm/1,55 µm fibroniques équipées d'une
fibre amorce pour la catégorie C – Environnement intérieur contrôlé
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et
les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.
IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.
Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - IEC Products & Services Portal - products.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications, symboles
en utilisant différents critères (numéro de référence, texte, graphiques et le glossaire. Avec un abonnement, vous aurez
comité d’études, …). Elle donne aussi des informations sur les toujours accès à un contenu à jour adapté à vos besoins.
projets et les publications remplacées ou retirées.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au monde,
Restez informé sur les nouvelles publications IEC. Just
avec plus de 22 500 articles terminologiques en anglais et en
Published détaille les nouvelles publications parues.
français, ainsi que les termes équivalents dans 25 langues
Disponible en ligne et une fois par mois par email.
additionnelles. Egalement appelé Vocabulaire
Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC 61753-082-02 ®
Edition 1.0 2024-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Performance
standard –
Part 082-02: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM devices for
category C – Indoor controlled environment
Dispositifs d’interconnexion et composants passifs fibroniques – Norme de
performance –
Partie 082-02: Dispositifs WWDM 1,31 µm/1,55 µm fibroniques équipées d'une
fibre amorce pour la catégorie C – Environnement intérieur contrôlé
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.10 ISBN 978-2-8322-8704-0
– 2 – IEC 61753-082-02:2024 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Test . 6
5 Test report . 7
6 Performance requirements. 7
6.1 Reference components . 7
6.2 Dimensions . 7
6.3 Sample size . 7
6.4 Test details and requirements . 8
Annex A (normative) Sample size . 13
Bibliography . 14
Table 1 – Single-mode spectral bands . 7
Table 2 – Operating wavelength range . 7
Table 3 – Test details and requirements for category C . 8
Table A.1 – Sample size of tests . 13
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES AND
PASSIVE COMPONENTS – PERFORMANCE STANDARD –
Part 082-02: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM
devices for category C – Indoor controlled environment
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 61753-082-02 has been prepared by subcommittee 86B: Fibre optic interconnecting
devices and passive components, of IEC technical committee 86: Fibre optics. It is an
International Standard.
This first edition cancels and replaces the first edition of IEC 61753-082-2 published in 2008.
This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) change of test conditions harmonizing with IEC 61753-1.
– 4 – IEC 61753-082-02:2024 © IEC 2024
The text of this International Standard is based on the following documents:
Draft Report on voting
86B/4867/FDIS 86B/4902/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 61753 series, published under the general title Fibre optic
interconnecting devices and passive components performance standard, can be found on the
IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
FIBRE OPTIC INTERCONNECTING DEVICES AND
PASSIVE COMPONENTS – PERFORMANCE STANDARD –
Part 082-02: Pigtailed single-mode fibre optic 1,31/1,55 µm WWDM
devices for category C – Indoor controlled environment
1 Scope
This part of IEC 61753 contains the minimum initial test, measurement requirements and
severities which a fibre optic 1,31/1,55 µm wide wavelength division multiplexing (WWDM)
device satisfies in order to be categorised as meeting the requirements of category C (indoor
controlled environment), as defined in IEC 61753-1:2018, Annex A. WWDM is defined in
IEC 62074-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60793-2-50, Optical fibres – Part 2-50: Product specifications – Sectional specification for
class B single-mode fibres
IEC 60794-2-50, Optical fibre cables – Part 2-50: Indoor cables – Family specification for
simplex and duplex cables for use in terminated cable assemblies
IEC 61300-1:2022, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 1: General and guidance,
IEC 61300-1:2022/AMD1:2024
IEC 61300-2-1, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-1: Tests – Vibration (sinusoidal)
IEC 61300-2-4, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-4: Tests – Fibre or cable retention
IEC 61300-2-5, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-5: Tests – Torsion
IEC 61300-2-9, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-9: Tests – Shock
IEC 61300-2-14, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-14: Tests – High optical power
IEC 61300-2-17, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-17: Tests – Cold
IEC 61300-2-18, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-18: Tests – Dry heat
– 6 – IEC 61753-082-02:2024 © IEC 2024
IEC 61300-2-19, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-19: Tests – Damp heat (steady state)
IEC 61300-2-22, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-22: Tests – Change of temperature
IEC 61300-2-42, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-42: Tests – Static side load for strain relief
IEC 61300-2-44, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 2-44: Tests – Flexing of the strain relief of fibre optic devices
IEC 61300-3-2, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-2: Examination and measurements – Polarization dependent
loss in a single-mode fibre optic device
IEC 61300-3-6, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-6: Examination and measurements – Return loss
IEC 61300-3-7, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-7: Examination and measurements – Wavelength
dependence of attenuation and return loss of single mode components
IEC 61300-3-29, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-29: Examinations and measurements – Spectral transfer
characteristics of DWDM devices
IEC 61753-1:2018, Fibre optic interconnecting devices and passive components – Performance
standard – Part 1: General and guidance
IEC 61753-1:2018/AMD1:2020
IEC 62074-1, Fibre optic interconnecting devices and passive components – Fibre optic WDM
devices – Part 1: Generic specification
IEC TS 62627-09, Fibre optic interconnecting devices and passive components – Vocabulary
for passive optical devices
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 62074-1 and
IEC TS 62627-09 apply.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
4 Test
All test methods are in accordance with a specific IEC 61300 series standard, of which parts
applicable to this document are mentioned in 6.4 (see Table 3).
The samples shall be terminated onto single-mode fibres as per IEC 60793-2-50 category
B-652.B, B-652.D or B-657 in either coated fibres (primary and secondary) or reinforced cable
format as per IEC 60794-2-50.
Table 1 is intended to provide guidance on the wavelength ranges of the various spectral bands.
It is not intended for specification. All tests shall be carried out over the wavelength range
defined by the customer’s application. The operating wavelength ranges for used WWDM are
given in Table 2.
Table 1 – Single-mode spectral bands
Band Descriptor Range
nm
O-band Original 1 260 to 1 360
E-band Extended 1 360 to 1 460
S-band Short wavelength 1 460 to 1 530
C-band Conventional 1 530 to 1 565
L-band Long wavelength 1 565 to 1 625
U-band Ultralong wavelength 1 625 to 1 675
Table 2 – Operating wavelength range
Operating wavelength range Operating wavelength range
nm nm
Variant 1 1 290 to 1 330 1 530 to 1 570
Variant 2 1 270 to 1 350 1 510 to 1 590
NOTE Other variants with different nominal channel central wavelengths and
operating wavelength ranges can be defined similarly in accordance with
IEC 62074-1.
5 Test report
Fully documented test reports and supporting evidence shall be prepared and be available for
inspection as evidence that the tests have been carried out and complied with.
6 Performance requirements
6.1 Reference components
The performance testing in this document does not require the use of reference components.
6.2 Dimensions
Dimensions shall comply with either an appropriate IEC interface standard or with those given
in appropriate manufacturers drawings, where the IEC interface standard does not exist or
cannot be used.
6.3 Sample size
Sample sizes are defined in Table A.1 of Annex A.
___________
Reproduced from ITU-T G-series Recommendations – Supplement 39, Optical system design and engineering
considerations, with the permission of ITU.
– 8 – IEC 61753-082-02:2024 © IEC 2024
6.4 Test details and requirements
The requirements are given only for pigtailed WWDM devices. For connectorized components
the connector performances shall be in compliance with IEC 61753-1.
A minimum length of fibre or cable of 2,0 m per port shall be used for all tests. Environmental
tests shall be in accordance with IEC 61300-1:2022/AMD1:2024, Annex C.
Minimum test details and requirements are shown in Table 3.
Table 3 – Test details and requirements for category C
No. Test Requirement Details
1 Centre wavelengths Centre wavelength: Launch patchcord ≥ 2 m
(CWL) length:
channel 1: 1 310 nm
IEC 61300-3-7
Source type: Unpolarised
channel 2: 1 550 nm
IEC 61300-3-29
Launch conditions: The wavelength of the source
shall be longer than the cut-off
wavelength of the fibre.
Measurement ≤ 0,05 nm
uncertainty:
2 Passband Variant 1 (of Table 2): Launch patchcord ≥ 2 m
length:
IEC 61300-3-7 CWL ± 20 nm
Source type: Unpolarised broadband light
IEC 61300-3-29 Variant 2 (of Table 2):
Launch conditions: The wavelength of the source
CWL ± 40 nm
shall be longer than the cut-off
wavelength of the fibre.
Passband is defined as
0,5 dB bandwidth.
Measurement ≤ 0,05 nm
uncertainty:
3 Attenuation ≤ 1,3 dB Launch patchcord ≥ 2 m
(insertion loss) length:
Attenuation shall be met
IEC 61300-3-7 over the operating
Source type: Unpolarised
wavelength range
Launch conditions: The wavelength of the source
according to Table 2.
shall be longer than the cut-off
NOTE Attenuation is the
wavelength of the fibre.
maximum value of the
Measurement ≤ 0,1 dB
attenuations within all
uncertainty:
passbands.
4 Wavelength isolation ≥ 15 dB (Type A) Launch patchcord ≥ 2 m
length:
IEC 61300-3-7 ≥ 40 dB (Type B)
Source type: Unpolarised
Wavelength isolation
shall be met over the
Launch conditions: The wavelength of the source
operating wavelength
shall be longer than the cut-off
range according to
wavelength of the fibre.
Table 2.
Measurement ≤ 0,1 dB
NOTE Technology type A
uncertainty:
is fused biconic taper
based WDM. Technology
type B is TFF technology
based WDM.
5 Out-of-band ≥ 20 dB Launch patchcord ≥ 2 m
attenuation length:
Out-of-band attenuation
IEC 61300-3-7 shall be met over the
Source type: Unpolarised
operating wavelength
IEC 61300-3-29
Launch conditions: The wavelength of the source
range according to
shall be longer than the cut-off
Table 2.
wavelength of the fibre.
Measurement ≤ 0,1 dB
uncertainty:
No. Test Requirement Details
6 Return loss ≥ 35 dB Grade T Source type: Laser diode (LD)
IEC 61300-3-6 ≥ 50 dB Grade U
Measurement ≤ 1 dB
uncertainty:
≥ 60 dB Grade V
Other requirements: All ports not under test shall
Return loss shall be met
be terminated to avoid
over the operating
unwanted reflections
wavelength range
contributing to the
according to Table 2.
measurement.
7 Polarisation ≤ 0,2 dB Launch patchcord ≥ 2 m
dependent loss (PDL) length:
PDL shall be met over the
IEC 61300-3-2 operating wavelength
Source type: LD
range according to
Measurement ≤ 0,05 dB
Table 2.
uncertainty:
8 High optical power During the test the Temperature: +60 °C ± 2 °C
attenuation limits of test
IEC 61300-2-14
Source type: LD
No. 3 shall be met.
Moreover, during and on
Max. total optical 300 mW
completion of the test,
power to be applied:
the attenuation shall be
NOTE It is the sum of the
within ± 0,5 dB of original
input power for all ports.
value under standard
Wavelength: For each port the desired
atmospheric conditions.
wavelength from test 1.
On completion of the test
Test duration: 0,5 h
the return loss limits of
test No. 6 shall be met.
Measurement Attenuation: ≤ 0,1 dB
On completion of the test uncertainty:
Return loss: ≤ 1 dB
the wavelength isolation
limits of test No. 4 shall
be met.
9 Cold During the test the Temperature: -10 °C ± 2 °C
attenuation limits of test
IEC 61300-2-17 Duration of the 96 h
No. 3 shall be met.
exposure:
Moreover, during and on
completion of the test,
Maximum sampling
1 h
the attenuation shall be
interval during the
within ± 0,5 dB of original
test:
value under standard
atmospheric conditions.
Measurements Attenuation shall be measured
required: before, during and after the
During and on completion
test.
of the test the return loss
limits of test No. 6 shall
Return loss shall be measured
be met.
before, during and after the
test.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
– 10 – IEC 61753-082-02:2024 © IEC 2024
No. Test Requirement Details
10 Dry heat During the test the Temperature: +60 °C ± 2 °C
attenuation limits of test
IEC 61300-2-18
Duration of the 96 h
No. 3 shall be met.
exposure:
Moreover, during and on
completion of the test,
Maximum sampling 1 h
the attenuation shall be
interval during the
within ± 0,5 dB of original
test:
value under standard
atmospheric conditions.
Measurements Attenuation shall be measured
required: before, during and after the
During and on completion
test.
of the test the return loss
limits of test No. 6 shall
Return loss shall be measured
be met.
before, during and after the
test.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
11 Change of During the test the High temperature: +60 °C ± 2 °C
temperature attenuation limits of test
Low temperature: -10 °C ± 2 °C
No. 3 shall be met.
IEC 61300-2-22
Moreover, during and on
Number of cycles: 5
completion of the test,
the attenuation shall be
Rate of temperature 1 °C/min
within ± 0,5 dB of original
change:
value under standard
Duration at extreme 1 h
atmospheric conditions.
temperatures:
During and on completion
of the test the return loss Maximum sampling 0,5 h
limits of test No. 6 shall interval during the
be met. test:
On completion of the test
Measurements Attenuation shall be measured
the wavelength isolation
required: before, during and after the
limits of test No. 4 shall
test.
be met.
Return loss shall be measured
before, during and after the
test.
12 Damp heat (steady During the test the Temperature: +40 °C ± 2 °C
state) attenuation limits of test
Humidity: 93 % RH +2 % RH / -3 % RH
No. 3 shall be met.
IEC 61300-2-19
Moreover, during and on
Duration of the 96 h
completion of the test,
exposure:
the attenuation shall be
within ± 0,5 dB of original
Maximum sampling 1 h
value under standard
interval during the
atmospheric conditions.
test:
During and on completion
Measurements Attenuation shall be measured
of the test the return loss
required: before, during and after the
limits of test No. 6 shall
test.
be met.
Return loss shall be measured
On completion of the test
before, during and after the
the wavelength isolation
test.
limits of test No. 4 shall
be met.
No. Test Requirement Details
13 Vibration (sinusoidal) On completion of the test Frequency range: 10 Hz to 55 Hz to 10 Hz
the attenuation limits of
IEC 61300-2-1
Amplitude: 0,75 mm
test No. 3 shall be met.
Number of cycles: 15
On completion of the test
the attenuation shall be
Sweep rate: 1 octave/min
within ± 0,5 dB of original
value.
Number of axes: 3 orthogonal
On completion of the test
Measurements Attenuation shall be measured
the return loss limits of
required: before and after the test.
test No. 6 shall be met.
Return loss shall be measured
On completion of the test
before and after the test.
the out-of-band
attenuation limits of test
No.5 shall be met.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
14 Shock On completion of the test Acceleration:
5 000 m/s
the attenuation limits of
IEC 61300-2-9
Number of axes: 3 main axes, perpendicular on
test No. 3 shall be met.
each other.
On completion of the test
the attenuation shall be Duration shock: 1 ms
within ± 0,5 dB of original
Pulse: Half sine
value.
Number of shocks: 2 per axis and direction (two in
On completion of the test
each direction).
the return loss limits of
test No. 6 shall be met.
Measurements Attenuation loss shall be
required: measured before and after the
On completion of the test
test.
the out-of-band
attenuation limits of test
Return loss shall be measured
No. 5 shall be met.
before and after the test.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
15 Fibre or cable On completion of the test Magnitude and rate of (10 N ± 1 N) at 5 N/s for
retention the attenuation limits of application: reinforced cable.
test No. 3 shall be met.
IEC 61300-2-4 (5,0 N ± 0,5 N) at 0,5 N/s for
On completion of the test secondary coated fibre.
the attenuation shall be
(2,0 N ± 0,2 N) at 0,5 N/s for
within ± 0,5 dB of original
primary coated fibre.
value.
Load application 200 mm ± 50 mm from the end
On completion of the test
point: of device.
the return loss limits of
test No. 6 shall be met.
Duration of the load: 60 s
On completion of the test
Measurements Attenuation shall be measured
the out-of-band
required: before and after the test.
attenuation limits of test
No. 5 shall be met.
Return loss shall be measured
before and after the test.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
– 12 – IEC 61753-082-02:2024 © IEC 2024
No. Test Requirement Details
16 Flexing of the strain On completion of the test Tensile force: (2,0 N ± 0,2 N) for 1 h for
relief of fibre optic the attenuation limits of reinforced cable.
devices test No. 3 shall be met.
Number of cycles: 50
IEC 61300-2-44 On completion of the test
Angle: ±90°
the attenuation shall be
within ± 0,5 dB of original
Load application 0,3 m from the end of device.
value.
point:
On completion of the test
the return loss limits of
Measurements Attenuation shall be measured
test No. 6 shall be met.
required: before and after the test.
On completion of the test
Return loss shall be measured
the out-of-band
before and after the test.
attenuation limits of test
No. 5 shall be met.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
17 Static side load for On completion of the test Magnitude of the (1,0 N ± 0,1 N) for reinforced
strain relief the attenuation limits of load: cable.
test No. 3 shall be met.
IEC 61300-2-42 (0,2 N ± 0,1 N) for secondary
On completion of the test
coated fibres.
the attenuation shall be
within ± 0,5 dB of original
Load application 200 mm to 300 mm from the
value.
point: end of device.
On completion of the test
Directions of load: Two mutually perpendicular
the return loss limits of
directions.
test No. 6 shall be met.
Duration of the load: 1 h for reinforced cable.
On completion of the test
the out-of-band
5 min for secondary coated
attenuation limits of test
fibres.
No. 5 shall be met.
Measurements Attenuation shall be measured
On completion of the test
required: before and after the test.
the wavelength isolation
limits of test No. 4 shall Return loss shall be measured
before and after the test.
be met.
18 Torsion On completion of the test Magnitude of the (5,0 N ± 0,2 N) for reinforced
the attenuation limits of torsion: cable.
IEC 61300-2-5
test No. 3 shall be met.
(2,0 N ± 0,1 N) for secondary
On completion of the test
coated fibres.
the attenuation shall be
within ± 0,5 dB of original
Number of cycles: 10
value.
Angle: ±180°
On completion of the test
the return loss limits of
Measurements Attenuation shall be measured
test No. 6 shall be met.
required: before and after the test.
On completion of the test
Return loss shall be measured
the out-of-band
before and after the test.
attenuation limits of test
No. 5 shall be met.
On completion of the test
the wavelength isolation
limits of test No. 4 shall
be met.
Annex A
(normative)
Sample size
Table A.1 – Sample size of tests
Test number Test Sample size
a
Centre wavelength NA
a
Passband NA
3 Attenuation 12
4 Wavelength isolation 12
5 Out-of-band attenuation 12
6 Return loss 12
7 Polarization dependent loss 12
8 High optical power 12
9 Cold 6
10 Dry heat 6
11 Change of temperature 6
12 Damp heat (steady state) 6
13 Vibration (sinusoidal) 6
14 Shock 6
15 Fibre or cable retention 6
16 Flexing of the strain relief of fibre optic devices 6
17 Static side load for strain relief 6
18 Torsion 6
a
For design information (not test item).
– 14 – IEC 61753-082-02:2024 © IEC 2024
Bibliography
IEC 61300 (all parts), Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures
ITU-T G-series Recommendations – Supplement 39, Optical system design and engineering
considerations
___________
– 16 – IEC 61753-082-02:2024 © IEC 2024
SOMMAIRE
AVANT-PROPOS . 17
1 Domaine d’application . 19
2 Références normatives . 19
3 Termes et définitions . 20
4 Essai . 21
5 Rapport d’essai . 21
6 Exigences relatives aux performances . 22
6.1 Composants de référence . 22
6.2 Dimensions . 22
6.3 Nombre d’échantillons . 22
6.4 Détails et exigences des essais . 22
Annexe A (normative) Nombre d’échantillons . 28
Bibliographie . 29
Tableau 1 – Bandes spectrales en unimodal . 21
Tableau 2 – Plages de longueurs d’onde de fonctionnement . 21
Tableau 3 – Détails et exigences des essais pour la catégorie C . 22
Tableau A.1 – Nombre d’échantillons pour les essais . 28
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
DISPOSITIFS D’INTERCONNEXION ET COMPOSANTS
PASSIFS FIBRONIQUES – NORME DE PERFORMANCE –
Partie 082-02: Dispositifs WWDM 1,31 µm /1,55 µm fibroniques
équipées d'une fibre amorce pour la catégorie C –
Environnement intérieur contrôlé
AVANT-PROPOS
1) La Commission Électrotechnique Internationale (IEC) est une organisation mondiale de normalisation composée
de l’ensemble des comités électrotechniques nationaux (Comités nationaux de l’IEC). L’IEC a pour objet de
favoriser la coopération internationale pour toutes les questions de normalisation dans les domaines de
l’électricité et de l'électronique. À cet effet, l’IEC – entre autres activités – publie des Normes internationales,
des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au public (PAS) et des
Guides (ci-après dénommés "Publication(s) de l’IEC”). Leur élaboration est confiée à des comités d'études, aux
travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les organisations
internationales, gouvernementales et non gouvernementales, en liaison avec l’IEC, participent également aux
travaux. L’IEC collabore étroitement avec l'Organisation Internationale de Normalisation (ISO), selon des
conditions fixées par accord entre les deux organisations.
2) Les décisions ou accords officiels de l’IEC concernant les questions techniques représentent, dans la mesure du
possible, un accord international sur les sujets étudiés, étant donné que les Comités nationaux de l’IEC intéressés
sont représentés dans chaque comité d’études.
3) Les Publications de l’IEC se présentent sous la forme de recommandations internationales et sont agréées
comme telles par les Comités nationaux de l’IEC. Tous les efforts raisonnables sont entrepris afin que l’IEC
s’assure de l’exactitude du contenu technique de ses publications; l’IEC ne peut pas être tenue responsable de
l’éventuelle mauvaise utilisation ou interprétation qui en est faite par un quelconque utilisateur final.
4) Dans le but d’encourager l’uniformité internationale, les Comités nationaux de l’IEC s’engagent, dans toute la
mesure possible, à appliquer de façon transparente les Publications de l’IEC dans leurs publications nationales
et régionales. Toutes divergences entre toutes Publications de l’IEC et toutes publications nationales ou
régionales correspondantes doivent être indiquées en termes clairs dans ces dernières.
5) L’IEC elle-même ne fournit aucune attestation de conformité. Des organismes de certification indépendants
fournissent des services d'évaluation de conformité et, dans certains secteurs, accèdent aux marques de
conformité de l’IEC. L’IEC n'est responsable d'aucun des services effectués par les organismes de certification
indépendants.
6) Tous les utilisateurs doivent s'assurer qu'ils sont en possession de la dernière édition de cette publication.
7) Aucune responsabilité ne doit être imputée à l’IEC, à ses administrateurs, employés, auxiliaires ou mandataires,
y compris ses experts particuliers et les membres de ses comités d’études et des Comités nationaux de l’IEC,
pour tout préjudice causé en cas de dommages corporels et matériels, ou de tout autre dommage de quelque
nature que ce soit, directe ou indirecte, ou pour supporter les coûts (y compris les frais de justice) et les dépenses
découlant de la publication ou de l’utilisation de cette Publication de l’IEC ou de toute autre Publication de l’IEC,
ou au crédit qui lui est accordé.
8) L’attention est attirée sur les références normatives citées dans cette publication. L'utilisation de publications
référencées est obligatoire pour une application correcte de la présente publication.
9) L'IEC attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation d'un
ou de plusieurs brevets. L'IEC ne prend pas position quant à la preuve, à la validité et à l'applicabilité de tout
droit de brevet revendiqué à cet égard. À la date de publication du présent document, l'IEC n'a pas reçu
notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois, il y a lieu
d'avertir les responsables de la mise en application du présent document que des informations plus récentes
sont susceptibles de figurer dans la base de données de brevets, disponible à l'adresse https://patents.iec.ch.
L'IEC ne saurait être tenue pour responsable de l'identification de ces droits de propriété en tout ou partie.
L’IEC 61753-082-02 a été établie par le sous-comité 86B: Dispositifs d'interconnexion et
composants passifs fibroniques, du comité d'études 86 de l'IEC: Fibres optiques. Il s’agit d’une
Norme internationale.
Cette première édition annule et remplace la première édition de l’IEC 61753-082-2 parue en
2008 et constitue une révision technique.
– 18 – IEC 61753-082-02:2024 © IEC 2024
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition
précédente:
a) modification des conditions d'essai pour harmonisation avec l’IEC 61753-1.
Le texte de cette Norme internationale est issu des documents suivants:
Projet Rapport de vote
86B/4867/FDIS 86B/4902/RVD
Le rapport de vote indiqué dans le tableau ci-dessus donne toute information sur le vote ayant
abouti à son approbation.
La langue employée pour l’élaboration de cette Norme internationale est l'anglais.
Ce document a été rédigé selon les Directives ISO/IEC, Partie 2, il a été développé selon les
Directives ISO/IEC, Partie 1 et les Directives ISO/IEC, Supplément IEC, disponibles sous
www.iec.ch/members_experts/refdocs. Les principaux types de documents développés par
l'IEC sont décrits plus en détail sous www.iec.ch/publications.
Une liste de toutes les parties de la série IEC 61753, publiées sous le titre général Dispositifs
d’interconnexion et composants passifs fibroniques norme de performance, se trouve sur le site
web de l'IEC.
Le comité a décidé que le contenu de ce document ne sera pas modifié avant la date de stabilité
indiquée sur le site web de l'IEC sous webstore.iec.ch dans les données relatives au document
recherché. À cette date, le document sera
• reconduit,
• supprimé, ou
• révisé.
DISPOSITIFS D’INTERCONNEXION ET COMPOSANTS
PASSIFS FIBRONIQUES – NORME DE PERFORMANCE –
Partie 082-02: Dispositifs WWDM 1,31 µm /1,55 µm fibroniques
équipées d'une fibre amorce pour la catégorie C –
Environnement intérieur contrôlé
1 Domaine d’application
La présente partie de l’IEC 61753 contient les exigences minimales initiales d’essai et de
mesure, ainsi que les sévérités auxquelles un dispositif fibronique de multiplexage par
répartition en longueur d’onde large (WWDM, Wide Wavelength Division Multiplexing)
1,31 µm/1,55 µm est tenu de satisfaire pour être classé comme étant conforme aux exigences
de la catégorie C (environnement intérieur contrôlé), selon la définition donnée dans
l’IEC 61753-1:2018, Annexe A. Le protocole WWDM est défini dans l’IEC 62074-1.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie
de leur contenu, des e
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...