IEC 61156-6-1:2007

Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Working area wiring - Blank detail specification

Describes symmetrical pair/quad cables intended for working area cabling in class D, E, EA, F and FA channels (Cat 5e, Cat 6, Cat 6A, Cat 7, Cat 7A) as defined in ISO/IEC 11801 and ISO/IEC 24702. Includes additional recommended environmental characteristics and severities, which are derived from the environmental classifications that are specified for cabling for industrial environments. includes the following significant technical changes with respect to the previous edition: a) new requirements for new cables Cat6A, Cat7A for 10 GBase-T applications; b) revised requirements and tests for the cables

General Information

• Status: Published
• Publication Date: 05-Jun-2007
• ICS: 33.120.20 - Wires and symmetrical cables
• Technical Committee: SC 46C - Wires and symmetric cables
• Drafting Committee: WG 7 - TC 46/SC 46C/WG 7
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 14-Oct-2009

Relations

• Revised: IEC 61156-6-1:2009 - Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Work area wiring - Blank detail specification
• Effective Date: 05-Sep-2023
• Revises: IEC 61156-6-1:2002 - Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz - Work area wiring - Blank detail specification
• Effective Date: 05-Sep-2023

Standards Content (Sample)

INTERNATIONAL IEC
STANDARD 61156-6-1
Second edition
2007-06
Multicore and symmetrical pair/quad
cables for digital communications –
Part 6-1:
Symmetrical pair/quad cables with
transmission characteristics up to 1 000 MHz –
Work area wiring – Blank detail specification

Reference number
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
INTERNATIONAL IEC
STANDARD 61156-6-1
Second edition
2007-06
Multicore and symmetrical pair/quad
cables for digital communications –
Part 6-1:
Symmetrical pair/quad cables with
transmission characteristics up to 1 000 MHz –
Work area wiring – Blank detail specification

PRICE CODE
Commission Electrotechnique Internationale K
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 61156-6-1 © IEC:2007(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________
MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES

FOR DIGITAL COMMUNICATIONS –
Part 6-1: Symmetrical pair/quad cables with transmission

characteristics up to 1 000 MHz – Working area wiring –

Blank detail specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all
national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-
operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in
this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also
participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in
accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all interested
IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between any
IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment
declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or other
damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising
out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 61156-6-1 has been prepared by subcommittee 46C: Wires and
symmetric cables, of IEC technical committee 46: Cables, wires, waveguides, r.f. connectors, r.f.
and microwave passive components and accessories.
This second edition cancels and replaces the first edition published in 2002. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) new requirements for new cables Cat6 , Cat7 for 10 GBase-T applications;
A A
b) revised requirements and tests for the cables.

61156-6-1 © IEC:2007(E) – 3 –
The text of this standard is based on the second edition and on the following documents:

FDIS Report on voting
46C/819/FDIS 46C/827/RVD
Full information on the voting for the approval of this standard can be found in the report on voting

indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

This specification is to be used in conjunction with IEC 61156-1 and IEC 61156-6.
A list of all parts of the IEC 61156 series, under the general title Multicore and symmetrical
pair/quad cables for digital communications, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

– 4 – 61156-6-1 © IEC:2007(E)
MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES

FOR DIGITAL COMMUNICATIONS –
Part 6-1: Symmetrical pair/quad cables with transmission

characteristics up to 1 000 MHz – Working area wiring –

Blank detail specification
1 Scope
This paart of IEC 61156 describes symmetrical pair/quad cables intended for working area cabling
in class D, E, E , F and F channels (Cat 5e, Cat 6, Cat 6 , Cat 7, Cat 7 ) as defined in ISO/IEC
A A A A
11801 and ISO/IEC 24702.
This blank detail specification includes additional recommended environmental characteristics and
severities, which are derived from the environmental classifications that are specified for cabling
for industrial environments.
NOTE Cabling for various severities of industrial environments is specified in ISO/IEC 24702. Environmental
classifications are presented in ISO/IEC 24702 with three levels of severity in four areas: mechanical, ingress, climatic,
and electromagnetic: thus, in tabular form, they are referred to as the “MICE table”.
The blank detail specification determines the layout and style for detail specifications describing
symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz for digital
communications. Detail specification
...