IEC 61156-6-1:2009
(Main)Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Work area wiring - Blank detail specification
Multicore and symmetrical pair/quad cables for digital communications - Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to 1 000 MHz - Work area wiring - Blank detail specification
IEC 61156-6-1:2009(E) describes symmetrical pair/quad cables intended primarily for horizontal floor cabling as defined in ISO/IEC 11801 and ISO/IEC 24702. It includes additional recommended environmental characteristics and severities which are derived from the environmental classifications that are specified for cabling for various environments. This edition constitutes a technical revision and includes the following significant technical changes with respect to the previous edition:
- new requirements for new cables Cat6A and Cat7A;
- revised requirements and tests for the cables.
This publication is to be read in conjunction with IEC 61156-1:2007 and IEC 61156-6:2007.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61156-6-1 ®
Edition 3.0 2009-10
INTERNATIONAL
STANDARD
Multicore and symmetrical pair/quad cables for digital communications –
Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to
1 000 MHz – Work area wiring – Blank detail specification
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61156-6-1 ®
Edition 3.0 2009-10
INTERNATIONAL
STANDARD
Multicore and symmetrical pair/quad cables for digital communications –
Part 6-1: Symmetrical pair/quad cables with transmission characteristics up to
1 000 MHz – Work area wiring – Blank detail specification
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
K
ICS 33.120.20 ISBN 978-2-88910-427-7
– 2 – 61156-6-1 © IEC:2009(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES
FOR DIGITAL COMMUNICATIONS –
Part 6-1: Symmetrical pair/quad cables
with transmission characteristics up to 1 000 MHz –
Work area wiring – Blank detail specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61156-6-1 has been prepared by subcommittee 46C: Wires and
symmetric cables, of IEC technical committee 46: Cables, wires, waveguides, r.f. connectors,
r.f. and microwave passive components and accessories.
This third edition cancels and replaces the second edition published in 2007. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
and Cat7 ;
a) new requirements for new cables Cat6
A A
b) revised requirements and tests for the cables.
61156-6-1 © IEC:2009(E) – 3 –
The text of this standard is based on the second edition and on the following documents:
CDV Report on voting
46C/863/CDV 46C/882/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This specification is to be used in conjunction with IEC 61156-1 and IEC 61156-6.
A list of all parts of the IEC 61156 series, under the general title: Multicore and symmetrical
pair/quad cables for digital communications, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
– 4 – 61156-6-1 © IEC:2009(E)
MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES
FOR DIGITAL COMMUNICATIONS –
Part 6-1: Symmetrical pair/quad cables
with transmission characteristics up to 1 000 MHz –
Work area wiring – Blank detail specification
1 Scope
This part of IEC 61156 describes symmetrical pair/quad cables intended primarily for work
area cabling as defined in ISO/IEC 11801 and ISO/IEC 24702.
NOTE Environmental classifications are presented in ISO/IEC 24702 with three levels of severity in four areas:
mechanical, ingress, climatic, and electromagnetic: thus, in tabular form, they are referred to as the “MICE table”.
This blank detail specification includes recommended environmental characteristics and
severities which are derived from the environmental classifications that are specified for
cabling for various environments.
The blank detail specification determines the layout and style for detail specifications
describing symmetrical pair/quad cables with transmission characteristics up to the maximum
frequency of the respective category for digital communications. Detail specifications, based
on the blank detail specification, may be prepared by a national organization, a manufacturer
or a user.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.