IEC 63171-1:2020
(Main)Connectors for electrical and electronic equipment - Part 1: Detail specification for two-way, shielded or unshielded, free and fixed connectors - Mechanical mating information, pin assignment and additional requirements for Type 1 copper LC style
Connectors for electrical and electronic equipment - Part 1: Detail specification for two-way, shielded or unshielded, free and fixed connectors - Mechanical mating information, pin assignment and additional requirements for Type 1 copper LC style
IEC 63171-1:2020 covers two-way, shielded or unshielded, free and fixed connectors for data transmission with frequencies up to 600 MHz and with current carrying capacity up to 2,0 A at 60 °C. It is intended to specify the common dimensions, mechanical, electrical, signal integrity, environmental characteristics, reliability specifications and corresponding tests for these connectors.
Connecteurs pour équipements électriques et électroniques - Partie 1: Spécification particulière pour les fiches et les embases bidirectionnelles, écrantées ou non écrantées - Informations sur l’accouplement mécanique, brochage et exigences supplémentaires pour connecteur LC de type 1 à doigts de guidage en cuivre
63171-1:2020 couvre les fiches et embases bidirectionnelles, écrantées ou non écrantées, assurant la transmission de données à des fréquences pouvant atteindre 600 MHz et à un courant admissible pouvant atteindre 2,0 A à 60 °C. Elle vise à spécifier les dimensions communes, les caractéristiques mécaniques, électriques, d’intégrité du signal et d’environnement, les spécifications de fiabilité et les essais correspondants pour ces connecteurs.
General Information
Buy Standard
Standards Content (sample)
IEC 63171-1
Edition 1.0 2020-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electrical and electronic equipment –
Part 1: Detail specification for two-way, shielded or unshielded, free and fixed
connectors – Mechanical mating information, pin assignment and additional
requirements for Type 1 copper LC style
Connecteurs pour équipements électriques et électroniques –
Partie 1: Spécification particulière pour les fiches et les embases
bidirectionnelles, écrantées ou non écrantées – Informations sur l’accouplement
mécanique, brochage et exigences supplémentaires pour connecteur LC de type
1 à doigts de guidage en cuivre
IEC 63171-1:2020-04(en-fr)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2020 IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 113, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have beenIEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IECLe contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.Recherche de publications IEC - Electropedia - www.electropedia.org
webstore.iec.ch/advsearchform Le premier dictionnaire d'électrotechnologie en ligne au
La recherche avancée permet de trouver des publications IEC monde, avec plus de 22 000 articles terminologiques en
en utilisant différents critères (numéro de référence, texte, anglais et en français, ainsi que les termes équivalents dans
comité d’études,…). Elle donne aussi des informations sur les 16 langues additionnelles. Egalement appelé Vocabulaire
projets et les publications remplacées ou retirées. Electrotechnique International (IEV) en ligne.
IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary
Restez informé sur les nouvelles publications IEC. Just 67 000 entrées terminologiques électrotechniques, en anglais
Published détaille les nouvelles publications parues. et en français, extraites des articles Termes et Définitions des
Disponible en ligne et une fois par mois par email. publications IEC parues depuis 2002. Plus certaines entrées
antérieures extraites des publications des CE 37, 77, 86 etService Clients - webstore.iec.ch/csc CISPR de l'IEC.
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
---------------------- Page: 2 ----------------------
IEC 63171-1
Edition 1.0 2020-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electrical and electronic equipment –
Part 1: Detail specification for two-way, shielded or unshielded, free and fixed
connectors – Mechanical mating information, pin assignment and additional
requirements for Type 1 copper LC style
Connecteurs pour équipements électriques et électroniques –
Partie 1: Spécification particulière pour les fiches et les embases
bidirectionnelles, écrantées ou non écrantées – Informations sur l’accouplement
mécanique, brochage et exigences supplémentaires pour connecteur LC de type
1 à doigts de guidage en cuivre
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.10 ISBN 978-2-8322-8076-8
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical CommissionMarque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
– 2 – IEC 63171-1:2020 © IEC 2020
CONTENTS
FOREWORD ........................................................................................................................... 4
INTRODUCTION ..................................................................................................................... 6
1 Scope .............................................................................................................................. 8
2 Normative references ...................................................................................................... 8
3 Terms and definitions ...................................................................................................... 9
4 Technical information .................................................................................................... 10
4.1 Compatibility level – Interoperability ...................................................................... 10
4.2 Unshielded connectors .......................................................................................... 10
4.3 Use of UTP cable .................................................................................................. 10
5 Common features and typical connector pair ................................................................. 10
5.1 Mating information ................................................................................................ 10
5.1.1 General ......................................................................................................... 10
5.1.2 Contacts – Mating conditions ......................................................................... 11
5.1.3 Fixed connector ............................................................................................. 12
5.1.4 Free connector .............................................................................................. 15
6 Characteristics .............................................................................................................. 16
6.1 General ................................................................................................................. 16
6.2 Classification into climatic category ...................................................................... 16
6.3 Electrical characteristics ....................................................................................... 17
6.3.1 General ......................................................................................................... 17
6.3.2 Creepage and clearance distances ................................................................ 17
6.3.3 Contact resistance – Interface only (separable fixed and free contact) ........... 17
6.3.4 Input to output DC resistance ........................................................................ 18
6.3.5 Input to output DC resistance unbalanced...................................................... 18
6.3.6 Voltage proof ................................................................................................. 18
6.3.7 Current-temperature derating ......................................................................... 18
6.3.8 Initial insulation resistance ............................................................................ 18
6.4 Transmission characteristics ................................................................................. 18
6.4.1 General ......................................................................................................... 18
6.4.2 Insertion loss (IL) ........................................................................................... 19
6.4.3 Return loss (RL) ............................................................................................ 19
6.4.4 Transverse conversion loss (TCL) ................................................................. 19
6.4.5 Transfer conversion transfer loss (TCTL) ....................................................... 19
6.4.6 Power sum alien near-end crosstalk loss (PS ANEXT) ................................... 19
6.4.7 Power sum alien far-end crosstalk loss (PS AFEXT) ...................................... 20
6.4.8 Transfer impedance (shielded only) ............................................................... 20
6.4.9 Coupling attenuation ...................................................................................... 20
6.5 Mechanical characteristics .................................................................................... 20
6.5.1 Mechanical operation ..................................................................................... 20
6.5.2 Effectiveness of connector coupling devices .................................................. 20
6.5.3 Insertion and withdrawal forces ..................................................................... 20
7 Tests and test schedule ................................................................................................. 21
7.1 General ................................................................................................................. 21
7.2 Arrangement for contact resistance measurement ................................................. 21
7.3 Arrangement for vibration test (test phase CP1) .................................................... 22
7.4 Test procedures and measuring methods .............................................................. 22
---------------------- Page: 4 ----------------------IEC 63171-1:2020 © IEC 2020 – 3 –
7.5 Preconditioning ..................................................................................................... 22
8 Test schedules .............................................................................................................. 23
8.1 Basic (minimum) test schedule.............................................................................. 23
8.2 Full test schedule .................................................................................................. 23
8.2.1 General ......................................................................................................... 23
8.2.2 Test group P – Preliminary ............................................................................ 23
8.2.3 Test group AP – Climatic ............................................................................... 24
8.2.4 Test group BP – Mechanical .......................................................................... 25
8.2.5 Test group CP – Vibration.............................................................................. 26
8.2.6 Test group DP – Electrical load ..................................................................... 27
8.2.7 Test group EP – Electrical transmission ......................................................... 27
8.2.8 Test group GP – Transfer Impedance and Coupling Attenuation .................... 28
Annex A (normative) Locking-device mechanical operation .................................................. 29
A.1 Object ................................................................................................................... 29
A.2 Preparation of the specimen ................................................................................. 29
A.3 Test method .......................................................................................................... 29
A.4 Final measurements .............................................................................................. 29
Bibliography .......................................................................................................................... 30
Figure 1 – Relationships between the IEC 63171 series and its related references ................. 7
Figure 2 – Connector overview ............................................................................................... 7
Figure 3 – Mated fixed and free connectors .......................................................................... 11
Figure 4 – Fixed connector ................................................................................................... 13
Figure 5 – Fixed connector pin detail (detail A from Figure 4c) section D-D) ......................... 14
Figure 6 – Free connector ..................................................................................................... 15
Figure 7 – Arrangement for contact resistance measurement ................................................ 21
Figure 8 – Arrangement for vibration test .............................................................................. 22
Table 1 – Dimensions for Figure 4a), Figure 4b) and Figure 4c) ............................................ 13
Table 2 – Dimensions for Figure 5 ........................................................................................ 14
Table 3 – Dimensions for Figure 6a) and Figure 6b) .............................................................. 16
Table 4 – Creepage and clearance distances ........................................................................ 17
Table 5 – Test group P ......................................................................................................... 23
Table 6 – Test group AP ....................................................................................................... 24
Table 7 – Test group BP ....................................................................................................... 25
Table 8 – Test group CP ....................................................................................................... 26
Table 9 – Test group DP ....................................................................................................... 27
Table 10 – Test Group EP..................................................................................................... 27
Table 11 – Test Group GP .................................................................................................... 28
---------------------- Page: 5 ----------------------– 4 – IEC 63171-1:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –
Part 1: Detail specification for two-way, shielded or unshielded, free and
fixed connectors – Mechanical mating information, pin assignment and
additional requirements for Type 1 copper LC style
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 63171-1 has been prepared by subcommittee 48B: Electrical
connectors of IEC technical committee 48: Electrical connectors and mechanical structures for
electrical and electronic equipment.The text of this International Standard is based on the following documents:
FDIS Report on voting
48B/2783/FDIS 48B/2799/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 6 ----------------------IEC 63171-1:2020 © IEC 2020 – 5 –
A list of all parts in the IEC 63171 series, published under the general title Connectors for
electrical and electronic components, can be found on the IEC website.The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 7 ----------------------
– 6 – IEC 63171-1:2020 © IEC 2020
INTRODUCTION
The International Electrotechnical Commission (IEC) draws attention to the fact that it is
claimed that compliance with this document may involve the use of a patent concerning
contact mating surface dimensions given in 5.1.The IEC takes no position concerning the evidence, validity and scope of this patent right.
The holder of the patent right on contact mating surface dimensions in 5.1 has assured the
IEC that they are willing to give free licences to applicants throughout the world. In this
respect, the statement of the holder of this patent right is registered with the IEC
Information may be obtained from:CommScope Technologies, LLC
501 Shenandoah Drive
Shakopee, Minnesota
USA 55379
Attention is drawn to the possibility that some of the elements of this International Standard
may be the subject of patent rights other than those identified above. IEC shall not be held
responsible for identifying any or all such patent rights.ISO (www.iso.org/patents) and IEC (http://patents.iec.ch) maintain on-line data bases of
patents relevant to their standards. Users are encouraged to consult the data bases for the
most up to date information concerning patents.IEC 63171 is the base specification of the whole series. Subsequent specifications do not
duplicate information given in the base document, but list only additional requirements. For
complete specification regarding a component of a higher number document the base
numbered documents should be considered as well. The following diagram (see Figure 1)
shows the interrelation of the documents:---------------------- Page: 8 ----------------------
IEC 63171-1:2020 © IEC 2020 – 7 –
Figure 1 – Relationships between the IEC 63171 series and its related references
International Electrotechnical Commission IEC 63171-1 Ed1
Subcommittee 48B: Electrical connectors
Two-way, free and fixed
connectors for data transmission
up to 600 MHz (and with current
carrying capacity up to 2,0 A at
60° C.)
Fixed connectors are mounted
on printed circuit board or bulk
head, the free connector is
terminated on shielded or
unshielded wire.
View showing typical fixed and free connectors
Figure 2 – Connector overview
---------------------- Page: 9 ----------------------
– 8 – IEC 63171-1:2020 © IEC 2020
CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT –
Part 1: Detail specification for two-way, shielded or unshielded, free and
fixed connectors – Mechanical mating information, pin assignment and
additional requirements for Type 1 copper LC style
1 Scope
This part of IEC 63171 covers two-way, shielded or unshielded, free and fixed connectors for
data transmission with frequencies up to 600 MHz and with current carrying capacity up
to 2,0 A at 60 °C. It is intended to specify the common dimensions, mechanical, electrical,
signal integrity, environmental characteristics, reliability specifications and corresponding
tests for these connectors.2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the reference document (including
any amendments) applies.IEC 60050-581, International Electrotechnical Vocabulary (IEV) – Chapter 581:
Electromechanical components for electronic equipment
IEC 60068-1, Environmental testing – Part 1: General and guidance
IEC 60512-1, Connectors for electrical and electronic equipment – Tests and measurements –
Part 1: Generic specificationIEC 60512-1-1, Connectors for electronic equipment – Tests and measurements – Part 1-1:
General examination – Test 1a: Visual examinationIEC 60512-1-2, Connectors for electronic equipment – Tests and measurements – Part 1-2:
General examination – Test 1b: Examination of dimension and massIEC 60512-2-1, Connectors for electronic equipment – Tests and measurements – Part 2-1:
Electrical continuity and contact resistance tests – Test 2a: Contact resistance – Millivolt level
methodIEC 60512-2-5, Connectors for electronic equipment – Tests and measurements – Part 2-5:
Electrical continuity and contact resistance tests – Test 2e: Contact disturbance
IEC 60512-3-1, Connectors for electronic equipment – Tests and measurements – Part 3-1:
Insulation tests – Test 3a: Insulation resistanceIEC 60512-4-1, Connectors for electronic equipment – Tests and measurements – Part 4-1:
Voltage stress tests – Test 4a: Voltage proofIEC 60512-5-2, Connectors for electronic equipment – Tests and measurements – Part 5-2:
Current-carrying capacity tests – Test 5b: Current-temperature derating---------------------- Page: 10 ----------------------
IEC 63171-1:2020 © IEC 2020 – 9 –
IEC 60512-6-4, Connectors for electronic equipment – Tests and measurements – Part 6:
Dynamic stress tests – Section 5: Test 6d: Vibration (sinusoidal)IEC 60512-9-1, Connectors for electronic equipment – Tests and measurements – Part 9-1:
Endurance tests – Test 9a: Mechanical operationIEC 60512-11-7, Connectors for electronic equipment – Tests and measurements – Part 11-7:
Climatic tests – Test 11g: Flowing mixed gas corrosion testIEC 60512-11-12, Connectors for electronic equipment – Tests and measurements – Part 11-
12: Climatic tests – Test 11m: Damp heat, cyclicIEC 60512-13-2, Connectors for electronic equipment – Tests and measurements – Part 13-2:
Mechanical operation tests – Test 13b: Insertion and withdrawal forcesIEC 60512-15-6, Connectors for electronic equipment – Tests and measurements – Part 15-6:
Connector tests (mechanical) – Test 15f: Effectiveness of connector coupling devices
IEC 60512-25-9, Connectors for electronic equipment – Tests and measurements – Part 25-9:
Signal integrity tests – Test 25i: Alien crosstalkIEC 60512-26-100, Connectors for electronic equipment – Tests and measurements – Part
26-100: Measurement setup, test and reference arrangements and measurements forconnectors according to IEC 60603-7 – Tests 26a to 26g
IEC 60512-28-100, Connectors for electrical and electronic equipment – Tests and
measurements – Part 28-100: Signal integrity tests up to 2 000 MHz – Tests 28a to 28g
IEC 60664-1, Insulation coordination for equipment within low-voltage systems – Part 1:
Principles, requirements and testsIEC 62153-4-12, Metallic communication cable test methods – Part 4-12: Electromagnetic
compatibility (EMC) – Coupling attenuation or screening attenuation of connecting hardware –
Absorbing clamp methodIEC 62153-4-15, Metallic communication cable test methods – Part 4-15: Electromagnetic
compatibility (EMC) – Test method for measuring transfer impedance and screeningattenuation – or coupling attenuation with triaxial cell
ISO/IEC 11801-1, Information technology – Generic cabling for customer premises – Part 1:
General requirements3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60050-581 and
IEC 60512-1 apply.ISO and IEC maintain terminology databases for use in the standardization at the following
addresses:• IEC Electropedia: available at http://www.electopedia.org
• ISO Online browsing platform: available at http://www.iso.org/obp
---------------------- Page: 11 ----------------------
– 10 – IEC 63171-1:2020 © IEC 2020
4 Technical information
4.1 Compatibility level – Interoperability
Interoperability of connectors from different sources that are in compliance to this document is
assured as a pre-requisite by compliance with the specified interface dimensions(intermateability) and by the relevant signal integrity tests specified.
The design of this copper LC style connector contains features in both the free and fixed
connectors that prevent intermateability with a standard LC fibre optic connector according to
IEC 61754-20. The key feature in the fixed connector, as shown in Figure 4c), prevents the
insertion of an LC fibre optic connector. The height of the free connector, shown
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.