IEC 61029-2-1:1993/AMD1:1999
(Amendment)Amendment 1 - Safety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saws
Amendment 1 - Safety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saws
General Information
Standards Content (Sample)
INTERNATIONAL IEC
STANDARD
61029-2-1
AMENDMENT 1
1999-02
Amendment 1
Safety of transportable motor-operated
electric tools –
Part 2-1:
Particular requirements for circular saws
Amendement 1
Sécurité des machines-outils électriques semi-fixes –
Partie 2.1:
Règles particulières pour les scies circulaires
IEC 1999 Copyright - all rights reserved
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch
Commission Electrotechnique Internationale
PRICE CODE
C
International Electrotechnical Commission
For price, see current catalogue
– 2 – 61029-2-1 Amend. 1 IEC:1999(E)
FOREWORD
This amendment has been prepared by subcommittee 61F: Safety of hand-held motor-operated
electric tools, of IEC technical committee 61: Safety of household and similar electrical
appliances.
The text of this amendment is based on the following documents:
FDIS Report on voting
61F/257/FDIS 61F/263/RVD
Full information on the voting for the approval of this amendment can be found in the report on
vo
...
This May Also Interest You
IEC 62841-3-4:2016 applies to transportable bench grinders that can be equipped with one or two accessories as follows:
- type 1 grinding wheels in accordance with ISO 603-4:1999 with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm;
- wire brushes with a diameter not exceeding 310 mm and a thickness not exceeding 55 mm;
- polishing wheels with a diameter not exceeding 310 mm and with a peripheral speed of any accessory between 10 m/s and 50 m/s. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Keywords: Bench Grinder, Hand-held tool, Transportable tool
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of December 2016 have been included in this copy.
- Standard8 pagesEnglish and French languagesale 15% off
- Standard46 pagesEnglish and French languagesale 15% off
- Standard94 pagesEnglish and French languagesale 15% off
- Standard99 pagesEnglish and French languagesale 15% off
IEC 62841-2-6:2020 Tools covered by this document include percussion hammers and rotary hammers, including rotary hammers with the capability to rotate only with the percussion system disengaged (drill only mode).
The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools.
This document does not apply to drills and impact drills.
This document does not apply to tools that are designed exclusively for driving fasteners, such as palm nailers.
- Standard118 pagesEnglish and French languagesale 15% off
- Standard242 pagesEnglish and French languagesale 15% off
IEC 62841-4-2:2017 applies to hand-held hedge trimmers which are designed for use by one operator for trimming hedges and bushes, including extended-reach hedge trimmers with a maximum length of 3,5 m. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3.
This standard is not applicable to hedge trimmers with a rotating blade.
This standard is not applicable to scissors type grass shears.
This Part 4-2 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication
The contents of the corrigendum of June 2018 have been included in this copy.
Key words: Hedge trimmer, Hand-held tool, Safety
- Standard167 pagesEnglish and French languagesale 15% off
- Standard422 pagesEnglish and French languagesale 15% off
IEC 62841-3-6:2014 applies to transportable diamond drills, intended to be connected to a liquid system. The liquid system may include liquid from a pipe or container. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Diamond drill, Drill unit, Drill stand
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of May 2015 have been included in this copy.
- Standard35 pagesEnglish and French languagesale 15% off
- Standard92 pagesEnglish and French languagesale 15% off
IEC 62841-3-1:2014 applies to transportable table saws with:
- a toothed single blade; or
- stacked blades that cut a single groove or slot; or
- a moulding head cutter intended for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter between 105 mm and 315 mm, which hereinafter may simply be referred to as saw or tool. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. This standard does not apply to table saws intended to cut other metals, such as magnesium, steel and iron. This standard does not apply to table saws with an automatic feeding device. This standard does not apply to saws designed for use with abrasive wheels. This standard does not apply to table saws with more than one spindle such as for a scoring blade. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. Key words: Table Saw, Transportable
This publication is to be read in conjunction with IEC 62841-1:2014. The contents of the corrigendum of November 2015 have been included in this copy.
- Standard99 pagesEnglish and French languagesale 15% off
- Standard208 pagesEnglish and French languagesale 15% off
IEC 62841-3-7:2020 This document applies to transportable wall saws guided by a track guiding system intended for dry cutting or to be connected to a liquid system for cutting concrete, stone or similar material by means of a diamond wheel. The rated speed of the diamond wheel does not exceed a peripheral speed of 100 m/s at rated capacity.
The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools.
This document does not apply to transportable wall saws that are intended to be left unattended while performing an operation.
This document does not apply to transportable wall saws that employ hydraulic systems.
This document does not apply to hand-held cut-off machines.
- Standard58 pagesEnglish and French languagesale 15% off
IEC 62841-2-3:2020: applies to hand-held grinders, disc-type polishers and disc-type sanders, including angle, straight and vertical tools, intended for use on various materials except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no-load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity.
This standard does not apply to dedicated cut-off machines.
This standard does not apply to orbital polishers and orbital sanders.
This standard does not apply to die grinders.
This Part 2-3 is to be used in conjunction with the first edition of IEC 62841-1:2014.
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. The contents of the corrigendum of April 2021 have been included in this copy.
- Standard140 pagesEnglish and French languagesale 15% off
IEC 62841-3-9:2020 is available as IEC 62841-3-9:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 62841-3-9:2020 applies to transportable mitre saws intended to be used with a toothed saw blade for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter not exceeding 410 mm, which hereinafter might simply be referred to as saw or tool. This International Standard does not apply to mitre saws intended to cut other metals, such as magnesium, steel and iron. This document does not apply to mitre saws with an automatic feeding device. Transportable saws intended to cut ferrous metals will be covered by a future part of IEC 62841-3. This document does not apply to saws designed for use with abrasive wheels. Transportable tools designed for use with abrasive wheels are covered by IEC 62841-3-10. This document does not apply to tools combining the function of a mitre saw with the function of a table saw. Transportable tools combining the function of a mitre saw with the function of a table saw are covered by by a future part of IEC 62841-3. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Clause 1: Scope: increase of the maximum saw blade diameter to 410 mm;
- Corrigendum 1 and Corrigendum 2 of the first edition have been incorporated in this second edition.
This Part 3-9 is to be used in conjunction with the IEC 62841-1:2014.
Key words: Hand-Held Tools, Transportable Mitre Saw
- Standard113 pagesEnglish languagesale 15% off
- Standard75 pagesEnglish and French languagesale 15% off
- Standard5 pagesEnglish and French languagesale 15% off
IEC 62841-2-11:2015 applies to applies to reciprocating saws such as jig saws and sabre saws.The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
This publication is to be read in conjunction with IEC 62841-1:2014.
- Standard46 pagesEnglish languagesale 15% off
- Standard44 pagesEnglish and French languagesale 15% off
- Standard92 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.