Laminated pressboard for electrical purposes - Part 1: Definitions, classification and general requirements

IEC 60763-1:2010 contains the definitions required for the understanding of all three parts of IEC 60763, the classification of material into types, and the general requirements applicable to all material covered by the standard. The main changes with respect to the previous edition is that the specification was brought in line with the second edition of IEC 60641-1(2007).

Cartons comprimés et contrecollés à usages électriques - Partie 1: Définitions, classification et exigences générales

La CEI 60763-1:2010 contient les définitions requises pour la compréhension de l'ensemble des trois parties de la CEI 60763, la classification des matériaux en types et les exigences générales applicables à tous les matériaux couverts par la norme. Les principales modifications par rapport à l'édition précédente est la spécification a été alignée avec la deuxième édition de la CEI 60641-1(2007).

General Information

Status
Published
Publication Date
05-Aug-2010
Current Stage
PPUB - Publication issued
Start Date
30-Nov-2010
Completion Date
06-Aug-2010
Ref Project

Buy Standard

Standard
IEC 60763-1:2010 - Laminated pressboard for electrical purposes - Part 1: Definitions, classification and general requirements
English and French language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC 60763-1
®
Edition 2.0 2010-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Laminated pressboard for electrical purposes –
Part 1: Definitions, classification and general requirements

Cartons comprimés et contrecollés à usages électriques –
Partie 1: Définitions, classification et exigences générales

IEC 60763-1:2010

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2010 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00

---------------------- Page: 2 ----------------------
IEC 60763-1
®
Edition 2.0 2010-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Laminated pressboard for electrical purposes –
Part 1: Definitions, classification and general requirements

Cartons comprimés et contrecollés à usages électriques –
Partie 1: Définitions, classification et exigences générales

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
F
CODE PRIX
ICS 29.035.10 ISBN 978-2-88912-145-8
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 3 ----------------------
– 2 – 60763-1 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

LAMINATED PRESSBOARD FOR ELECTRICAL PURPOSES –

Part 1: Definitions, classification and general requirements


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60763-1 has been prepared by IEC technical committee 15: Solid
electrical insulating materials.
This second edition cancels and replaces the first edition published in 1983. This edition
constitutes a technical revision.
The main changes with respect to the previous edition are as follows:
– the specification was brought in line with the second edition of IEC 60641-1(2007).
The text of this standard is based on the following documents:
CDV Report on voting
15/536/CDV 15/566/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

---------------------- Page: 4 ----------------------
60763-1 © IEC:2010 – 3 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
Future standards in this series will carry the new general title as cited above. Titles of existing
standards in this series will be updated at the time of the next edition.
A list of all the parts in the IEC 60763 series can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 5 ----------------------
– 4 – 60763-1 © IEC:2010
LAMINATED PRESSBOARD FOR ELECTRICAL PURPOSES –

Part 1: Definitions, classification and general requirements



1 Scope
This part of IEC 60763 contains the definitions required for the understanding of all three
parts of IEC 60763, the classification of material into types, and the general requirements
applicable to all material covered by the standard.
Materials which conform to this specification meet established levels of performance.
However, the selection of a material by a user for a specific application should be based on
the actual requirements necessary for adequate performance in that application and not
based on this specification alone.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60641-1:2007, Pressboard and presspaper for electrical purposes – Part 1: Definitions
and general requirements
3 Terms and definitions
For the purposes of this document the following definitions apply:
3.1
pressboard
board normally made on an intermittent board machine from pulp made entirely from
vegetable origin of high chemical purity. It is characterized by its relatively high density, even
thickness, surface smoothness, high mechanical strength, flexibility, ageing resistance and
electrical insulating properties. The surface may be smooth or textured
3.2
laminated pressboard
board built up from sheets of pressboard bonded with an adhesive
4 Classification
Based on compositions and properties, this standard covers the types of laminated
pressboard shown in Table 1. The designation of types is the same as that given in
IEC 60641-1; in addition, “L” is shown for “laminated” (for example LB0.1). To the description
of the types some examples of known applications are added without implying any restriction
on other possible applications.

---------------------- Page: 6 ----------------------
60763-1 © IEC:2010 – 5 –

Table 1 – Classification
Type Subdivisions Example of
application
LB0 Pressboard of particularly high LB0.1 100 % sulphate wood pulp Electrical equipment
chemical purity LB0.2 100 % cotton where particularly
LB0.3 Mixture of sulphate wood pulp high chemical purity
and cotton is required
LB2 Pressboard characterized by high LB2.1 100 % sulphate wood pulp Transformers
chemical purity LB2.2 100 % cotton
LB2.3 Mixture of sulphate wood pulp
and cotton
LB2.4 Mixture of cotton and jute hemp
LB3 Pre-compressed pressboard, a very LB3.1 100 % sulphate wood pulp Transformers
hard and rigid board characterized LB3.2 100 % cotton
by high chemical purity and LB3.3 Mixture of sulphate wood pulp
mechanical strength. Its surface and cotton
bears a cloth mark LB3.4 Mixture of cotton and jute hemp
LB4 Pressboard characterized by high LB4.1 100 % sulphate wood pulp Transformers and
chemical purity and high oil LB4.2 100 % cotton oil-immersed
absorption and capable of being LB4.3 Mixture of sulphate wood pulp equipment
shaped and cotton
LB4.4 Mixture
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.