IEC 60317-42:1997+AMD1:2010 CSV

Specifications for particular types of winding wires - Part 42: Polyester-amide-imide enamelled round copper wire, class 200

This consolidated version consists of the first edition (1997) and its amendment 1 (2010). Therefore, no need to order amendment in addition to this publication.

Spécifications pour types particuliers de fils de bobinage - Partie 42: Fil de section circulaire en cuivre émaillé avec polyester-amide-imide, classe 200

Cette version consolidée comprend la première édition (1997) et son amendement 1 (2010). Il n'est donc pas nécessaire de commander l'amendement avec cette publication.

General Information

• Status: Published
• Publication Date: 03-Jan-2021
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 29.060.10 - Wires
• Technical Committee: TC 55 - Winding wires
• Current Stage: WPUB - Publication withdrawn
• Completion Date: 04-Jan-2021

Standards Content (Sample)

IEC 60317-42
®
Edition 1.1 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 42: Polyester-amide-imide enamelled round copper wire, class 200

Spécifications pour types particuliers de fils de bobinage –
Partie 42: Fil de section circulaire en cuivre émaillé avec polyester-amide-imide,
classe 200
IEC 60317-42:1997+A1:2010

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2010 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]

---------------------- Page: 2 ----------------------
IEC 60317-42
®
Edition 1.1 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Specifications for particular types of winding wires –
Part 42: Polyester-amide-imide enamelled round copper wire, class 200

Spécifications pour types particuliers de fils de bobinage –
Partie 42: Fil de section circulaire en cuivre émaillé avec polyester-amide-imide,
classe 200

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CB
CODE PRIX
ICS 29.060.10 ISBN 978-2-88910-959-30
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 3 ----------------------
– 2 – 60317-42 © IEC:1997+A1:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
–––––––

SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –

Part 42: Polyester-amide-imide enamelled round
copper wire, class 200



FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

This consolidated version of IEC 60317-42 consists of the first edition (1997) [documents
55/531/FDIS and 55/566/RVD] and its amendment 1 (2010) [documents 55/1128/CDV and
55/1158/RVC]. It bears the edition number 1.1.
The technical content is therefore identical to the base edition and its amendment and
has been prepared for user convenience. A vertical line in the margin shows where the
base publication has been modified by amendment 1. Additions and deletions are
displayed in red, with deletions being struck through.

---------------------- Page: 4 ----------------------
60317-42 © IEC:1997+A1:2010 – 3 –
International Standard IEC 60317-42 has been prepared by IEC technical committee 55:
Winding wires.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch"
in the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.

---------------------- Page: 5 ----------------------
– 4 – 60317-42 © IEC:1997+A1:2010
INTRODUCTION

This part of IEC 60317 forms an element of a series which deals with insulated wires used for
windings in electrical equipment. The series has three groups describing:
1) methods of test (IEC 60851);
2) specifications (IEC 60317);
3) packaging (IEC 60264).

---------------------- Page: 6 ----------------------
60317-42 © IEC:1997+A1:2010 – 5 –
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –

Part 42: Polyester-amide-imide enamelled round
copper wire, class 200



1 Scope
This part of IEC 60317 specifies the requirements of enamelled round copper winding wire of
class 200 with a sole coating based on polyester-amide-imide resin, which may be modified
providing it retains the chemical identity of the original resin and meets all specified wire
requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
Class 200 is a thermal class that requires a minimum temperature index of 200 and a heat
shock temperature of at least 220 °C.
The temperature in degrees Celsius corresponding to the temperature index is not necessarily
that at which it is recommended that the wire be operated and this will depend on many factors,
including the type of equipment involved.
The range of nominal conductor diameters covered by this part is:
– Grade 1: 0,018 mm up to and including 1,600 mm;
– Grade 2: 0,025 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in clause 4 of IEC 60317-0-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
IEC 317-0-1: 1990, Specifications for particular types of winding wires – Part 0: General
requirements – Section 1: Enamelled round copper wire
IEC 60317-0-1:2008, Specifications for particular types of winding wires – Part 0-1: General
requirements – Enamelled round copper wire

---------------------- Page: 7 ----------------------
– 6 – 60317-42 © IEC:1997+A1:2010
3 Definitions and general notes on methods of test and appearance
3.1 Definitions and general notes on methods of test
For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-1.
In case of inconsistencies between IEC 60317-0-1 and this standard, IEC 60317-42 shall
prevail.
3.2 Appearance
See Subclause 3.3 of IEC 60317-0-1.
4 Dimensions
See clause 4 of IEC 60317-0-1.
5 Electrical resistance
See clause 5 of IEC 60317-0-1.
6 Elongation
See clause 6 of IEC 60317-0-1.
7 Springiness
See clause 7 of IEC 60317-0-1.
8 Flexibility and adherence
See clause 8 of IEC 60317-0-1, where the constant K used for the calculation of the number of
revolutions for the peel test shall be 110 mm.
9 Heat shock
See clause 9 of IEC 60317-0-1, where the minimum heat shock temperature shall be 220 °C.
10 Cut-through
No failure shall occur within 2 min at 300 °C.
11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to
and including 2,500 mm)
The wire shall meet the requirements given in table 1.

---------------------- Page: 8 --
...