IEC TR 60825-13:2006

Safety of laser products - Part 13: Measurements for classification of laser products

This Technical Report provides manufacturers, test houses, safety personnel, and others with practical guidance on methods to perform radiometric measurements or analyses to establish the emission level of laser energy in accordance with IEC 60825-1 (herein referred to as "the standard"). The measurement procedures described in this technical report are intended as guidance for classification of laser products in accordance with, that standard. Other procedures are acceptable if they are better or more appropriate. Information is provided for calculating accessible emission limits (AELs) and maximum permissible exposures (MPEs), since some parameters used in calculating the limits are dependent upon other measured quantities. This document is intended to apply to lasers, including extended sources and laser arrays. Users of this document should be aware that the procedures described herein for extended source viewing conditions may yield more conservative results than when using more rigorous methods.

General Information

• Status: Published
• Publication Date: 10-Aug-2006
• ICS: 31.260 - Optoelectronics. Laser equipment
• Technical Committee: TC 76 - Optical radiation safety and laser equipment
• Drafting Committee: WG 3 - TC 76/WG 3
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 19-Oct-2011

Relations

• Revised: IEC TR 60825-13:2011 - Safety of laser products - Part 13: Measurements for classification of laser products
• Effective Date: 05-Sep-2023

Standards Content (Sample)

TECHNICAL IEC
REPORT TR 60825-13
First edition
2006-08
Safety of laser products –
Part 13:
Measurements for classification
of laser products
Reference number
IEC/TR 60825-13:2006(E)
Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the
60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.
Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example,
edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the
base publication incorporating amendment 1 and the base publication incorporating
amendments 1 and 2.
Further information on IEC publications
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology. Information relating to
this publication, including its validity, is available in the IEC Catalogue of
publications (see below) in addition to new editions, amendments and corrigenda.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is also available from the following:
• IEC Web Site (www.iec.ch)
• Catalogue of IEC publications
The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to
search by a variety of criteria including text searches, technical committees
and date of publication. On-line information is also available on recently issued
publications, withdrawn and replaced publications, as well as corrigenda.
• IEC Just Published
This summary of recently issued publications (www.iec.ch/online_news/ justpub)
is also available by email. Please contact the Customer Service Centre (see
below) for further information.
• Customer Service Centre
If you have any questions regarding this publication or need further assistance,
please contact the Customer Service Centre:

Email: [e-mail]
Tel: [phone]
Fax: [phone]
TECHNICAL IEC
REPORT TR 60825-13
First edition
2006-08
Safety of laser products –
Part 13:
Measurements for classification
of laser products
 IEC 2006  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale W

International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – TR 60825-13  IEC:2006(E)
CONTENTS
FOREWORD.3

1 Scope.5
2 Normative references .5
3 Terms and definitions .5
4 Applicability.7
4.1 General .7
4.2 Initial considerations .7
5 Instrumentation requirements .8
6 Classification flow.8
7 Parameters for calculation of accessible emission limits .12
7.1 Wavelength (λ).12
7.2 Multiple wavelength sources.13
7.3 Spectrally broad sources .14
7.4 Source temporal behaviour.16
7.5 Angular subtense (α).18
7.6 Emission duration.26
7.7 Measurement conditions.26
7.8 Scanning beams.27

Annex A (informative) Large source classification example .32

Bibliography.37

Figure 1 – Continuous wave laser classification flow.10
Figure 2 – Pulsed laser classification flow.11
Figure 3 – Important wavelengths and wavelength ranges .12
Figure 4 – Pulse duration definition.17
Figure 5 – Flat-topped and irregular pulses.18
Figure 6 – Examples of angular subtense .19
Figure 7 – Location of beam waist for a Gaussian beam .20
Figure 8 – Source measurement geometries .24
Figure 9 – Linear array apparent source size .25
Figure 10 – Effective angular subtense of a simple non-circular source .26
Figure 11 – Imaging a stationary apparent source located beyond the scanning beam
vertex .28
Figure 12 – Imaging a scanning apparent source located beyond the scanning beam
vertex .28

Table 1 – Reference points .20
Table 2 – Four source array.23

TR 60825-13  IEC:2006(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
SAFETY OF LASER PRODUCTS –
Part 13: Measurements for classification of laser products

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a technical report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC 60825-13, which is a technical report, has been prepared by IEC technical committee 76:
Optical radiation safety and laser equipment.
The text of this technical report is based on the following documents:
Enquiry draft Report on voting
76/332/DTR 76/345/RVC
Full information on the voting for the approval of this technical report can be found in the
report on voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – TR 60825-13  IEC:2006(E)
This technical report is to be used in conjunction with IEC 60825-1:1993 and its Amendment 1
(1997) and Amendment 2 (2001), referred to in this report as “the standard”.
A list of all parts of the IEC 60825 series, published under the general title Safety of laser
products, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

TR 60825-13  IEC:2006(E) – 5 –
SAFETY OF LASER PRODUCTS –
Part 13: Measurements for classification of laser products

1 Scope
This part of IEC 60825 provides manufacturers, test houses, safety personnel, and others
with practical guidance on methods to perform radiometric measurements or analyses to
establish the emission level of laser energy in accordance with IEC 60825-1 (herein referred
to as “the standard”). The measurement procedures described in this technical report are
intended as guidance for classification of laser products in accordance with, that standard.
Other procedures are acceptable if they are better or more appropriate.
Information is provided for calculating accessible emission limits (AELs) and maximum
permissible exposures (MPEs), since some parameters used in calculating the limits are
dependent upon other measured quantities.
This document is intended to apply to lasers, including extended sources and laser arrays.
Users of this document should be aware that the procedures described herein for extended
source viewing conditions may yield more conservative results than when using more rigorous
methods.
NOTE Work continues on more complex source evaluations and will be provided as international agreement on
the methods is reached.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60825-1:1993, Safety of laser products – Part 1: Equipment classification, requirements
1)
and user’s guide
Amendment 1 (1997)
Amendment 2 (2001)
IEC 61040, Power and energy measuring detectors, instruments and equipment for laser
radiation
ISO 11554, Optics and optical instruments – Lasers and laser-related equipment – Test
methods for laser beam power, energy and temporal characteristics
3 Terms and definitions
For the purposes of this document, the terms and definitions contained in IEC 60825-1 as well
as the following apply.
3.1
angular velocity
speed of a scanning beam in radians per second
___________
1)
There exists a consolidated edition (1.2) of IEC 60825-1 (1993), including its Amendment 1 (1997) and
Amendment 2 (2001).
– 6 – TR 60825-13  IEC:2006(E)
3.2
beam profile
the ir
...