IEC 60440:2012
(Main)Method of measurement of non-linearity in resistors
Method of measurement of non-linearity in resistors
IEC 60440:2012 specifies a method of measurement and associated test conditions to assess the magnitude of non-linear distortion generated in a resistor. This method is applied if prescribed by a relevant component specification, or if agreed between a customer and a manufacturer. This International Standard cancels and replaces the Technical Report IEC/TR 60440, published in 1973. The major changes with regard to the Technical Report are:
- change of the principle parameter's term from "third harmonic attenuation" to "third harmonic ratio";
- addition of advice on the prescription of requirements in a relevant component specification;
- addition of a set of recommended measuring conditions for a specimen with a rated dissipation of less than 100 mW;
- a complete editorial revision.
Méthode de mesure de la non-linéarite des résistances
La CEI 60440:2012 spécifie une méthode de mesure et les conditions d'essais associées pour déterminer l'amplitude de la distorsion non linéaire générée dans une résistance. Cette méthode est appliquée si elle est prescrite par une spécification applicable au composant, ou si elle fait l'objet d'un accord entre un client et un fabricant. La présente Norme internationale annule et remplace le Rapport technique CEI/TR 60440, paru en 1973. Les modifications principales par rapport au Rapport technique sont les suivantes:
- modification du terme du paramètre principal d'"affaiblissement de troisième harmonique" en "rapport de troisième harmonique";
- ajout de conseils sur la prescription d'exigences dans une spécification applicable au composant;
- ajout d'un ensemble de conditions de mesure recommandées pour un spécimen ayant une dissipation assignée inférieure à 100 mW;
- révision éditoriale complète.
General Information
Relations
Standards Content (Sample)
IEC 60440 ®
Edition 1.0 2012-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Method of measurement of non-linearity in resistors
Méthode de mesure de la non-linéarite des résistances
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.
IEC 60440 ®
Edition 1.0 2012-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Method of measurement of non-linearity in resistors
Méthode de mesure de la non-linéarite des résistances
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX Q
ICS 31.040 ISBN 978-2-83220-228-9
– 2 – 60440 © IEC:2012
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Method of measurement . 6
4.1 Measurement principle . 6
4.2 Measuring circuit . 8
4.3 Measurement system requirements . 9
4.3.1 Measuring frequency . 9
4.3.2 Noise level of the measuring system . 9
4.3.3 Third harmonic ratio of the measuring system . 9
4.3.4 Power amplifier . 9
4.3.5 Voltmeter . 10
4.3.6 Filter . 10
4.3.7 Test fixture . 10
4.4 Verification of the measuring system . 10
5 Measurement procedure . 10
5.1 Environmental conditions . 10
5.2 Preparation of specimen . 10
5.3 Measurement conditions . 10
5.4 Procedure . 11
5.5 Precautions . 11
6 Evaluation of measurement results . 11
6.1 Evaluation . 11
6.2 Requirements . 12
7 Information to be given in the relevant component specification. 12
Annex A (informative) Reference to IEC/TR 60440 . 15
Bibliography . 16
Figure 1 – Equivalent circuit at the fundamental frequency . 6
Figure 2 – Equivalent circuit at the third harmonic frequency . 7
Figure 3 – Corrective term Δ . 8
Figure 4 – Block schematic of a suitable measuring system . 9
Table 1 – Recommended measuring conditions (1 of 2) . 13
60440 © IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
METHOD OF MEASUREMENT OF NON-LINEARITY IN RESISTORS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60440 has been prepared by committee 40: Capacitors and
resistors for electronic equipment.
This International Standard cancels and replaces the Technical Report IEC/TR 60440,
published in 1973.
The major changes with regard to the Technical Report are:
– change of the principle parameter’s term from “third harmonic attenuation” to “third
harmonic ratio”;
– addition of advice on the prescription of requirements in a relevant component
specification;
– addition of a set of recommended measuring conditions for a specimen with a rated
dissipation of less than 100 mW;
– a complete editorial revision.
– 4 – 60440 © IEC:2012
The text of this standard is based on the following documents:
FDIS Report on voting
40/2155/FDIS 40/2167/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
60440 © IEC:2012 – 5 –
METHOD OF MEASUREMENT OF NON-LINEARITY IN RESISTORS
1 Scope
Non-linearity testing is a method to evaluate the integrity of a resistive element. It may be
applied as an effective inline screening method suitable to detect and eliminate potential
infant mortality failures in passive components. The method is fairly rapid, convenient, and the
associated equipment is relatively inexpensive.
Typical effects causing non-linearity on resistors are e.g. inhomogeneous spots within a
resistive film, traces of film left in the spiraling grooves, or conta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.