31.060.01 - Capacitors in general
ICS 31.060.01 Details
Capacitors in general
Kondensatoren im allgemeinen
Condensateurs en general
Kondenzatorji na splošno
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 31.060.01 - Capacitors in general
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
NEW!IEC 62576:2018 is available as IEC 62576:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 62576:2018 describes the methods for testing electrical characteristics of electric double-layer capacitor cells (hereinafter referred to as capacitor) to be used for peak power assistance in hybrid electric vehicles. This second edition cancels and replaces the first edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) information on applicability of this document has been added in Clause 1;
b) the definitions of some terms in Clause 3 have been improved;
c) the description of test procedures in Clause 4 has been clarified;
d) information on endurance cycling test has been added (Annex E).
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
IEC corrigendum
- Corrigendum5 pagesEnglish languagesale 10% offe-Library read for1 day
Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62146-1:2013 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-component for the circuit-breaker and shall be specified in accordance with the circuit-breaker specifications. This standard applies to grading capacitors falling into one or both of the following categories for: - mounting on air-insulated circuit-breakers; - mounting on enclosed circuit-breakers (for example immersed in SF6, in oil, etc.). The testing for each of the above applications is in some cases different. The object of this standard is: - to define uniform rules regarding performances, testing and rating; - to define specific safety rules; - to provide a guidance for installation and operation. Keywords: grading capacitors, circuit-breakers
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard9 pagesEnglish and French languagesale 15% off
This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m.
- Amendment8 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60063:2015 provides series of preferred values for the resistance of resistors and for the capacitance of capacitors. The definition of such series with a defined numeric resolution is a basic prerequisite for the marking and coding of capacitors and resistors with their respective capacitance or resistance values as described in IEC 60062. This edition includes the following significant technical changes with respect to the previous edition:
- revision of the information on a relationship between an E Series and the tolerance of a resistance or capacitance value of a respective component;
- introduction of advice on a possible deduction from the marking of a component to an associated E Series and also to an associated tolerance;
- complete editorial revision.
- Standard20 pagesEnglish and French languagesale 15% off
IEC 62146-1:2013 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-component for the circuit-breaker and shall be specified in accordance with the circuit-breaker specifications. This standard applies to grading capacitors falling into one or both of the following categories for:
- mounting on air-insulated circuit-breakers;
- mounting on enclosed circuit-breakers (for example immersed in SF6, in oil, etc.). The testing for each of the above applications is in some cases different. The object of this standard is:
- to define uniform rules regarding performances, testing and rating;
- to define specific safety rules;
- to provide a guidance for installation and operation. Keywords: grading capacitors, circuit-breakers
- Standard71 pagesEnglish and French languagesale 15% off
- Standard142 pagesEnglish and French languagesale 15% off
IEC 60549:2013 applies to external fuses used with high-voltage capacitors according to IEC 60871-1, Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V - Part 1: General. IEC 60871-1 is applicable to both capacitor units and capacitor banks intended to be used, particularly, for power-factor correction of a.c. power systems, and also to capacitors intended for use in power filter circuits. Fuses according to IEC 60549:2013 are intended to clear either faults inside a capacitor unit to permit continued operation of the remaining parts of the bank in which the unit is connected (unit fuses) or faults on the whole capacitor bank to isolate the bank from the system (line fuses). This second edition cancels and replaces the first edition published in 1976. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - alignment of the document with current IEC document structure requirements; - clarification of certain test requirements. Keywords: external fuses used with high-voltage capacitors, shunt capacitors for a.c.power system
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following: - employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions from Table 1 to the informative Annex A, - addition of two smaller diameters of wire terminations in Table 1, and - tightening of the tolerance ranges defined by minimum and maximum diameters in Table 1.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60717:2012 applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE: Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges. The main technical changes with respect to the first edition are the following: - employment of the millimetre-based grid, the preferred grid system given in IEC 60097, - employment of SI units only, causing deletion of the imperial dimensions from Table 1, - reduction of the tolerance on the chamfer depth in Figure 1, and - introduction of requirements on information to be given in a relevant specification.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following:
- employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions from Table 1 to the informative Annex A,
- addition of two smaller diameters of wire terminations in Table 1, and
- tightening of the tolerance ranges defined by minimum and maximum diameters in Table 1.
- Standard12 pagesEnglish and French languagesale 15% off
IEC 60717:2012 applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE: Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges. The main technical changes with respect to the first edition are the following:
- employment of the millimetre-based grid, the preferred grid system given in IEC 60097,
- employment of SI units only, causing deletion of the imperial dimensions from Table 1,
- reduction of the tolerance on the chamfer depth in Figure 1, and
- introduction of requirements on information to be given in a relevant specification.
- Standard20 pagesEnglish and French languagesale 15% off
IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.
- Standard21 pagesEnglish and French languagesale 15% off
IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.
- Standard29 pagesEnglish and French languagesale 15% off
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesEnglish and French languagesale 15% off
IEC 60915:2006 contains preferred dimensions for shaft ends and bushes and for the mounting of single-hole, bush-mounted, shaft-operated variable capacitors, variable resistors and potentiometers. If other dimensions not listed in this standard have to be used, it is recommended to select them also from IEC 60390 and IEC 60620. This second edition cancels and replaces the first edition published in 1987 and constitutes a minor revision, related to tables, figures and references. This bilingual version, published in 2008-07, corresponds to the English version. The contents of the corrigendum of December 2008 have been included in this copy.
- Standard15 pagesEnglish languagesale 15% off
- Standard31 pagesEnglish and French languagesale 15% off
This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60062:2004 specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors. This edition includes the following significant technical changes with respect to the previous edition:
a) completion of the existing code systems for
- resistors with a three-character code system and a four-character code system;
- temperature coefficient of resistance with a letter code system;
- data code system for capacitors and resistors with the 10-year cycle code (two-character code), the 20-year cycle code (four-digit code), the 10-year cycle code (four-digit code), and a one-character code - four-year cycle.
b) extension with a code letter system for the dielectric material of plastic film and paper capacitors.
- Standard15 pagesEnglish languagesale 15% off
- Standard30 pagesEnglish and French languagesale 15% off
Specifies the requirements for both self-healing and non-self- healing continuously rated a.c. capacitors of up to and including 2,5 kvar, and not less than 0,1 F, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. Does not cover radio-interference suppressor capacitors, the requirements for which are given in IEC 60384-14.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
It has the status of a horizontal standard in accordance with IEC Guide 108.
- Standard15 pagesEnglish, French and Russian languagesale 15% off
- Standard33 pagesEnglish, French and Russian languagesale 10% offe-Library read for1 day
- Standard – translation18 pagesSlovenian, English, German and French languagesale 10% offe-Library read for1 day
It has the status of a horizontal standard in accordance with IEC Guide 108.
- Standard – translation26 pagesSlovenian languagesale 10% offe-Library read for1 day
Gives preferred values for fixed resistors and capacitors for ordinary and close tolerances of resistors and capacitors used in electronic equipment.
- Standard15 pagesEnglish and French languagesale 15% off
- Draft42 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft42 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62576:2009 describes the methods for testing electrical characteristics of electric double-layer capacitor cells (hereinafter referred to as capacitor) to be used for peak power assistance in hybrid electric vehicles.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
Presents preferred diameters in tabular form in the metric and inch-pound unit sizes.
- Standardization document6 pagesEnglish languagesale 10% offe-Library read for1 day
EN following parallel vote
- Amendment16 pagesEnglish languagesale 10% offe-Library read for1 day
Specifies the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kvar, and not less than 0,1 F, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. Does not cover radio-interference suppressor capacitors the requirements for which are given in IEC 60384-14.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
EN following parallel vote * Corrigendum to EN/A1 issued December 1998
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Specifies a colour code of 12 colours for values and tolerances of fixed resistors and a letter and digit code for resistance and capacitance values and tolerances.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
Superseded by EN 60062:2005
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
Superseded by EN 60062:2005
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day