IEC 61162-3:2008
(Main)Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 3: Serial data instrument network
Maritime navigation and radiocommunication equipment and systems - Digital interfaces - Part 3: Serial data instrument network
IEC 61162-3:2008 provides information for the application of NMEA 2000 aboard SOLAS vessels. Exceptions, additions and specific requirements for implementation upon SOLAS vessels are contained in the document. The NMEA 2000 standard contains the requirements for the implementation of a serial-data communications network adopting controller area network (CAN) technology.
Matériels et systèmes de navigation et de radiocommunication maritimes - Interfaces numériques - Partie 3: Réseau par liaison de données série d'instruments
L’IEC 61162-3:2008 est basée sur la norme NMEA 2000. La norme NMEA 2000 contient les exigences relatives à la mise en œuvre minimale d’un réseau par liaison de données série de communication pour interconnecter les matériels électroniques maritimes à bord des navires. Les matériels conçus conformément à la présente norme ont la capacité de partager des données, y compris commandes et états, avec d’autres matériels compatibles sur un seul canal de signalisation.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61162-3
Edition 1.0 2008-05
INTERNATIONAL
STANDARD
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61162-3
Edition 1.0 2008-05
INTERNATIONAL
STANDARD
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
Q
ICS 47.020.70 ISBN 2-8318-9811-0
– 2 – 61162-3 © IEC:2008(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms, definitions and conventions.7
3.1 Terms and definitions .7
3.2 Conventions .10
4 Physical layer.10
4.1 CAN transceiver .10
4.2 Environmental .10
4.3 Radio frequency interference.10
4.3.1 Unwanted electromagnetic emissions .10
4.3.2 Immunity to electromagnetic environment .10
4.4 Cables.10
4.5 Interface power .11
4.6 Network power source.11
5 Data link layer .11
6 Network layer .11
7 Network management.11
7.1 Address configuration method .11
7.2 Address retention .11
8 Application layer.11
8.1 Parameter groups.11
8.1.1 Parameter group priority.11
8.1.2 Parameter group broadcast rate .12
9 Test criteria .12
10 Application notes.12
11 Manufacturer’s documentation.12
Annex A (informative) System integration .13
Figure A.1 – Example of configuration .
Figure A.2 – Example of configuration .15
Table A.1 – Test characteristics.14
61162-3 © IEC:2008(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61162-3 has been prepared by IEC technical committee 80:
Maritime navigation and radiocommunication equipment and systems.
The text of this standard is based on the following documents:
CDV Report on voting
80/496/CDV 80/526/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – 61162-3 © IEC:2008(E)
A list of all parts of the IEC 61162 series, under the general title Maritime navigation and
radiocommunication equipment and systems – Digital interfaces, can be found on the IEC
website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
61162-3 © IEC:2008(E) – 5 –
INTRODUCTION
This part of IEC 61162 has been developed by the IEC technical committee 80 working
group 6, to meet the requirement for a versatile and economic means of connecting a wide
range of marine navigation and radiocommunications equipment aboard SOLAS vessels. The
National Marine Electronics Association’s Standard Committee has developed the NMEA
1 2
2000® standard. The NMEA 2000 Standard provides for capabilities across all classes of
vessels. The development of NMEA 2000 began in 1994 and was completed in 1999. More
than a dozen manufacturers worldwide conducted a two-year beta test. The finalised NMEA
2000 standard version 1.000 was published in 2001. IEC and NMEA have worked together
since 1999 to ensure that the NMEA 2000 standard fully supports SOLAS applications. NMEA
2000 version 1.200 was published in 2004, with expanded support for redundant messaging
and for equipments such as AIS.
The need for an improved standard, compared with IEC 61162-1 and IEC 61162-2, has arisen
due to the increased complexity of the latest equipment and systems. This requires multiple
links between equipment and greatly improved communication speed.
The parts 400 of the IEC 61162 series have already been issued and cater for the most
complex systems to be found on board a ship.
This new part 3 of IEC 61162 adopts the controller area network (CAN) technology, already
well established for many industrial systems. This permits a versatile system to be
established with the minimum of effort and reasonable cost. The equipment types supported
and the sentence data content developed for IEC 61162-1 has been retained.
IEC 61162-3 describes a low cost, moderate capacity, bi-directional multi-transmitter/multi-
receiver instrument network to interconnect marine electronic equipment. The connectors and
TM
and
cables used are compatible with industrial bus systems for instance DeviceNet
TM
Profibus .
IEC 61162-3 provides for the application of NMEA 2000 aboard SOLAS vessels. Exceptions,
additions and specific requirements for implementation upon SOLAS vessels are contained in
this document.
—————————
NMEA 2000® is the registered trademark of the National Marine Electronics Association, Inc. This information
is given for the convenience of users of this International Standard and does not constitute an endorsement by
IEC of the trademark holder or any of its products. Compliance to this profile does not require use of the trade
name. Use of the trade name requires permission of the trade holder.
NMEA is the registered trademark of the National Marine Electronics Association, Inc. This information is given
for the convenience of users of this International Standard and does not constitute an endorsement by IEC of
the trademark holder or any of its products. Compliance to this profile does not require use of the trade name.
Use of the trade name requires permission of the trade holder.
TM
DeviceNet is the registered trademark of the Open DeviceNet Vendor Association, Inc. This information is
given for the convenience of users of this International Standard and does not constitute an endorsement by
IEC of the trademark holder or any of its products. Compliance to this profile does not require use of the trade
name. Use of the trade name requires permission of the trade holder.
TM
Profibus is the registered trademark of PROFIBUS International. Thi
...
IEC 61162-3 ®
Edition 1.1 2010-11
INTERNATIONAL
STANDARD
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
§ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
§ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
§ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
§ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61162-3 ®
Edition 1.1 2010-11
INTERNATIONAL
STANDARD
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
CF
ICS 47.020.70 ISBN 978-2-88912-190-8
– 2 – 61162-3 Ó IEC:2008+A1:2010(E)
CONTENTS
FOREW ORD . 3
INTRODUCTION . 5
1 Sc o pe . 6
2 Normative references . 6
3 Terms, definitions and conventions . 7
3.1 Terms and definitions . 7
3.2 Conventions . 10
4 Physical layer . 10
4.1 CAN transceiver . 10
4.2 Environmental. 10
4.3 Radio frequency interference. 10
4.3.1 Unwanted electromagnetic emissions . 10
4.3.2 Immunity to electromagnetic environment . 10
4.4 Cables . 10
4.5 Interface power . 11
4.6 Network power source . 11
5 Data link layer . 11
6 Network layer . 11
7 Network management . 11
7.1 Address configuration method . 11
7.2 Address retention . 11
8 Application layer . 11
8.1 Parameter groups . 11
8.1.1 Parameter group priority . 11
8.1.2 Parameter group broadcast rate . 12
9 Test criteria. 12
10 Application notes . 12
11 Manufacturer’s documentation . 12
Annex A (informative) System integration . 13
Bibliography . 17
Figure A.1 – Example of configuration . 15
Figure A.2 – Example of configuration . 15
Table A.1 – Test characteristics . 14
61162-3 Ó IEC:2008+A1:2010(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of IEC 61162-3 consists of the first edition (2008) [documents
80/496/CDV and 80/526/RVC] and its amendment 1 (2010) [documents 80/580/CDV and
80/594/RVC]. It bears the edition number 1.1.
The technical content is therefore identical to the base edition and its amendment and
has been prepared for user convenience. A vertical line in the margin shows where the
base publication has been modified by amendment 1. Additions and deletions are
displayed in red, with deletions being struck through.
– 4 – 61162-3 Ó IEC:2008+A1:2010(E)
International Standard IEC 61162-3 has been prepared by IEC technical committee 80:
Maritime navigation and radiocommunication equipment and systems.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61162 series, under the general title Maritime navigation and
radiocommunication equipment and systems – Digital interfaces, can be found on the IEC
website.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will
be
reconfirmed,
withdrawn,
replaced by a revised edition, or
amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.
61162-3 Ó IEC:2008+A1:2010(E) – 5 –
INTRODUCTION
This part of IEC 61162 has been developed by the IEC technical committee 80 working
group 6, to meet the requirement for a versatile and economic means of connecting a wide
range of marine navigation and radiocommunications equipment aboard SOLAS vessels. The
National Marine Electronics Association’s Standard Committee has developed the NMEA
1 2
2000â standard. The NMEA 2000 Standard provides for capabilities across all classes of
vessels. The development of NMEA 2000 began in 1994 and was completed in 1999. More
than a dozen manufacturers worldwide conducted a two-year beta test. The finalised NMEA
2000 standard version 1.000 was published in 2001. IEC and NMEA have worked together
since 1999 to ensure that the NMEA 2000 standard fully supports SOLAS applications. NMEA
2000 version 1.200 was published in 2004, with expanded support for redundant messaging
and for equipments such as AIS.
The need for an improved standard, compared with IEC 61162-1 and IEC 61162-2, has arisen
due to the increased complexity of the latest equipment and systems. This requires multiple
links between equipment and greatly improved communication speed.
The parts 400 of the IEC 61162 series have already been issued and cater for the most
complex systems to be found on board a ship.
This new part 3 of IEC 61162 adopts the controller area network (CAN) technology, already
well established for many industrial systems. This permits a versatile system to be
established with the minimum of effort and reasonable cost. The equipment types supported
and the sentence data content developed for IEC 61162-1 has been retained.
IEC 61162-3 describes a low cost, moderate capacity, bi-directional multi-transmitter/multi-
receiver instrument network to interconnect marine electronic equipment. The connectors and
TM
cables used are compatible with industrial bus systems for instance DeviceNet and
TM
Profibus .
IEC 61162-3 provides for the application of NMEA 2000 aboard SOLAS vessels. Exceptions,
additions and specific requirements for implementation upon SOLAS vessels are contained in
this document.
INTRODUCTION
(to Amendment 1)
The amendment updates the normative reference for NMEA 2000 Appendix B to a later
version which includes five new sentences: PGN # 129807 - AIS Class B Group Assignment,
PGN # 129809 - AIS Class B "CS" Static Report Part A, PGN # 129810 - AIS Class B, PGN #
129039 - AIS Class B Position Report, and PGN # 129040 - AIS Class B Extended Position
Report.
—————————
NMEA 2000® is the registered trademark of the National Marine Electronics Association, Inc. This information
is
...
IEC 61162-3 ®
Edition 1.2 2014-07
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing more than 30 000 terms and
Technical Specifications, Technical Reports and other definitions in English and French, with equivalent terms in 14
documents. Available for PC, Mac OS, Android Tablets and additional languages. Also known as the International
iPad. Electrotechnical Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a More than 55 000 electrotechnical terminology entries in
variety of criteria (reference number, text, technical English and French extracted from the Terms and Definitions
committee,…). It also gives information on projects, replaced clause of IEC publications issued since 2002. Some entries
and withdrawn publications. have been collected from earlier publications of IEC TC 37,
77, 86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC 61162-3 ®
Edition 1.2 2014-07
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 40.020.70 ISBN 978-2-8322-1755-9
IEC 61162-3 ®
Edition 1.2 2014-07
CONSOLIDATED VERSION
REDLINE VERSION
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
– 2 – IEC 61162-3:2008
+AMD1:2010+AMD2:2014 CSV IEC 2014
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
INTRODUCTION to Amendment 1 . 6
INTRODUCTION to Amendment 2 . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and conventions . 9
3.1 Terms and definitions . 9
3.2 Conventions . 12
4 Physical layer . 12
4.1 CAN transceiver . 12
4.2 Environmental . 12
4.3 Radio frequency interference . 12
4.3.1 Unwanted electromagnetic emissions . 12
4.3.2 Immunity to electromagnetic environment . 12
4.4 Cables . 12
4.5 Interface power . 13
4.6 Network power source . 13
5 Data link layer . 13
6 Network layer . 13
7 Network management . 13
7.1 Address configuration method . 13
7.2 Address retention . 13
8 Application layer . 13
8.1 Parameter groups . 13
8.1.1 Parameter group priority . 13
8.1.2 Parameter group broadcast rate . 14
9 Test criteria . 14
10 Application notes . 14
11 Manufacturer’s documentation . 14
Annex A (informative) System integration . 15
Annex B (informative) Relationship between IEC 61162-1 sentences and IEC 61162-3
parameter group numbers . 19
Figure A.1 – Example of configuration . 17
Figure A.2 – Example of configuration . 17
Table A.1 – Test characteristics . 16
Table B.1 – Conversion from IEC 61162-1 to IEC 61162-3 . 19
Table B.2 – Conversion from IEC 61162-3 to IEC 61162-1 . 23
+AMD1:2010+AMD2:2014 CSV IEC 2014
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of the official IEC Standard and its amendments has been
prepared for user convenience.
IEC 61162-3 edition 1.2 contains the first edition (2008-05) [documents 80/496/CDV and
80/526/RVC], its amendment 1 (2010-06) [documents 80/580/CDV and 80/594/RVC] and its
amendment 2 (2014-07) [documents 80/714/CDV and 80/734/RVC].
In this Redline version, a vertical line in the margin shows where the technical content is
modified by amendments 1 and 2. Additions and deletions are displayed in red, with
deletions being struck through. A separate Final version with all changes accepted is
available in this publication.
– 4 – IEC 61162-3:2008
+AMD1:2010+AMD2:2014 CSV IEC 2014
International Standard IEC 61162-3 has been prepared by IEC technical committee 80:
Maritime navigation and radiocommunication equipment and systems.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61162 series, under the general title Maritime navigation and
radiocommunication equipment and systems – Digital interfaces, can be found on the IEC
website.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.
+AMD1:2010+AMD2:2014 CSV IEC 2014
INTRODUCTION
This part of IEC 61162 has been developed by the IEC technical committee 80 working
group 6, to meet the requirement for a versatile and economic means of connecting a wide
range of marine navigation and radiocommunications equipment aboard SOLAS vessels. The
National Marine Electronics Association’s Standard Committee has developed the NMEA
1 2
standard. The NMEA 2000 Standard provides for capabilities across all classes of
2000
vessels. The development of NMEA 2000 began in 1994 and was completed in 1999. More
than a dozen manufact
...
IEC 61162-3 ®
Edition 1.0 2008-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d’instruments
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC online collection - oc.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 000 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 18 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - IEC online collection - oc.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications. Avec un
en utilisant différents critères (numéro de référence, texte, abonnement, vous aurez toujours accès à un contenu à jour
comité d’études, …). Elle donne aussi des informations sur adapté à vos besoins.
les projets et les publications remplacées ou retirées.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au
Restez informé sur les nouvelles publications IEC. Just
monde, avec plus de 22 000 articles terminologiques en
Published détaille les nouvelles publications parues.
anglais et en français, ainsi que les termes équivalents dans
Disponible en ligne et une fois par mois par email.
16 langues additionnelles. Egalement appelé Vocabulaire
Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC 61162-3 ®
Edition 1.0 2008-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d’instruments
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 47.020.70 ISBN 978-2-8322-9336-2
– 2 – IEC 61162-3:2008 IEC 2008
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and conventions . 7
3.1 Terms and definitions . 7
3.2 Conventions . 10
4 Physical layer . 10
4.1 CAN transceiver . 10
4.2 Environmental . 10
4.3 Radio frequency interference . 10
4.3.1 Unwanted electromagnetic emissions . 10
4.3.2 Immunity to electromagnetic environment . 10
4.4 Cables . 10
4.5 Interface power . 11
4.6 Network power source . 11
5 Data link layer . 11
6 Network layer . 11
7 Network management . 11
7.1 Address configuration method . 11
7.2 Address retention . 11
8 Application layer . 11
8.1 Parameter groups . 11
8.1.1 Parameter group priority . 11
8.1.2 Parameter group broadcast rate . 12
9 Test criteria . 12
10 Application notes . 12
11 Manufacturer’s documentation . 12
Annex A (informative) System integration . 13
Bibliography . 17
Figure A.1 – Example of configuration . 15
Figure A.2 – Example of configuration . 15
Table A.1 – Test characteristics . 14
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61162-3 has been prepared by IEC technical committee 80:
Maritime navigation and radiocommunication equipment and systems.
The text of this standard is based on the following documents:
CDV Report on voting
80/496/CDV 80/526/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – IEC 61162-3:2008 IEC 2008
A list of all parts of the IEC 61162 series, under the general title Maritime navigation and
radiocommunication equipment and systems – Digital interfaces, can be found on the IEC
website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IEC 61162
...
IEC 61162-3 ®
Edition 1.1 2010-11
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d'instruments
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC online collection - oc.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 000 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 18 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - IEC online collection - oc.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications. Avec un
en utilisant différents critères (numéro de référence, texte, abonnement, vous aurez toujours accès à un contenu à jour
comité d’études, …). Elle donne aussi des informations sur adapté à vos besoins.
les projets et les publications remplacées ou retirées.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au
Restez informé sur les nouvelles publications IEC. Just
monde, avec plus de 22 000 articles terminologiques en
Published détaille les nouvelles publications parues.
anglais et en français, ainsi que les termes équivalents dans
Disponible en ligne et une fois par mois par email.
16 langues additionnelles. Egalement appelé Vocabulaire
Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC 61162-3 ®
Edition 1.1 2010-11
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d'instruments
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 47.020.70 ISBN 978-2-8322-4796-9
IEC 61162-3 ®
Edition 1.1 2010-11
CONSOLIDATED VERSION
REDLINE VERSION
VERSION REDLINE
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d'instruments
– 2 – IEC 61162-3:2008+AMD1:2010 CSV
IEC 2010
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
INTRODUCTION to Amendment 1 . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and conventions . 7
3.1 Terms and definitions . 7
3.2 Conventions . 10
4 Physical layer . 10
4.1 CAN transceiver . 10
4.2 Environmental . 10
4.3 Radio frequency interference . 10
4.3.1 Unwanted electromagnetic emissions . 10
4.3.2 Immunity to electromagnetic environment . 10
4.4 Cables . 10
4.5 Interface power . 11
4.6 Network power source . 11
5 Data link layer . 11
6 Network layer . 11
7 Network management . 11
7.1 Address configuration method . 11
7.2 Address retention . 11
8 Application layer . 11
8.1 Parameter groups . 11
8.1.1 Parameter group priority . 11
8.1.2 Parameter group broadcast rate . 12
9 Test criteria . 12
10 Application notes . 12
11 Manufacturer’s documentation . 12
Annex A (informative) System integration . 13
Bibliography . 17
Figure A.1 – Example of configuration . 15
Figure A.2 – Example of configuration . 15
Table A.1 – Test characteristics . 14
IEC 2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This consolidated version of the official IEC Standard and its amendment has been
prepared for user convenience.
IEC 61162-3 edition 1.1 contains the first edition (2008-05) [documents 80/496/CDV and
80/526/RVC] and its amendment 1 (2010-06) [documents 80/580/CDV and 80/594/RVC].
In this Redline version, a vertical line in the margin shows where the technical content
is modified by amendment 1. Additions are in green text, deletions are in st
...
IEC 61162-3 ®
Edition 1.2 2014-07
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d'instruments
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC online collection - oc.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 000 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 18 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - IEC online collection - oc.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications. Avec un
en utilisant différents critères (numéro de référence, texte, abonnement, vous aurez toujours accès à un contenu à jour
comité d’études, …). Elle donne aussi des informations sur adapté à vos besoins.
les projets et les publications remplacées ou retirées.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au
Restez informé sur les nouvelles publications IEC. Just
monde, avec plus de 22 000 articles terminologiques en
Published détaille les nouvelles publications parues.
anglais et en français, ainsi que les termes équivalents dans
Disponible en ligne et une fois par mois par email.
16 langues additionnelles. Egalement appelé Vocabulaire
Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC 61162-3 ®
Edition 1.2 2014-07
CONSOLIDATED VERSION
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d'instruments
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 47.020.70 ISBN 978-2-8322-1004-8
IEC 61162-3 ®
Edition 1.2 2014-07
CONSOLIDATED VERSION
REDLINE VERSION
VERSION REDLINE
colour
inside
Maritime navigation and radiocommunication equipment and systems –
Digital interfaces –
Part 3: Serial data instrument network
Matériels et systèmes de navigation et de radiocommunication maritimes –
Interfaces numériques –
Partie 3: Réseau par liaison de données série d'instruments
– 2 – IEC 61162-3:2008+AMD1:2010
+AMD2:2014 CSV IEC 2014
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
INTRODUCTION to Amendment 1 . 5
INTRODUCTION to Amendment 2 . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and conventions . 8
3.1 Terms and definitions . 8
3.2 Conventions . 11
4 Physical layer . 11
4.1 CAN transceiver . 11
4.2 Environmental . 11
4.3 Radio frequency interference . 11
4.3.1 Unwanted electromagnetic emissions . 11
4.3.2 Immunity to electromagnetic environment . 11
4.4 Cables . 11
4.5 Interface power . 12
4.6 Network power source . 12
5 Data link layer . 12
6 Network layer . 12
7 Network management . 12
7.1 Address configuration method . 12
7.2 Address retention . 12
8 Application layer . 12
8.1 Parameter groups . 12
8.1.1 Parameter group priority . 12
8.1.2 Parameter group broadcast rate . 13
9 Test criteria . 13
10 Application notes . 13
11 Manufacturer’s documentation . 13
Annex A (informative) System integration . 14
Annex B (informative) Relationship between IEC 61162-1 sentences and IEC 61162-3
parameter group numbers . 18
Bibliography . 26
Figure A.1 – Example of configuration . 16
Figure A.2 – Example of configuration . 16
Table A.1 – Test characteristics . 15
Table B.1 – Conversion from IEC 61162-1 to IEC 61162-3 . 18
Table B.2 – Conversion from IEC 61162-3 to IEC 61162-1 . 22
+AMD2:2014 CSV IEC 2014
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MARITIME NAVIGATION AND RADIOCOMMUNICATION
EQUIPMENT AND SYSTEMS –
DIGITAL INTERFACES –
Part 3: Serial data instrument network
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.