Multicore and symmetrical pair/quad cables for digital communications - Part 10: Cables for cords with transmission characteristics up to 2 GHz - Sectional specification

IEC 61156-10:2016(E) describes cables primarily intended for work area cords as defined in ISO/IEC 11801 and in ISO/IEC TR 11801-9901 which is planned to be included in the next edition of ISO/IEC 11801-1. It covers overall screened cables with screened (X/FTP) or unscreened (X/UTP) pairs, where X stands for F, S or SF, as well as pair-screened cables without overall screen (U/FTP). The transmission characteristics of these cables are specified up to a frequency of 2 000 MHz and at a temperature of 20 °C. Two categories of cables are recognised:
- Category 8.1 for use in Class I according to ISO/IEC TR 11801-9901;
- Category 8.2 for use in Class II according to ISO/IEC TR 11801-9901.

General Information

Status
Published
Publication Date
19-Apr-2016
Current Stage
PPUB - Publication issued
Start Date
15-Jun-2016
Completion Date
20-Apr-2016
Ref Project

Buy Standard

Standard
IEC 61156-10:2016 - Multicore and symmetrical pair/quad cables for digital communications - Part 10: Cables for cords with transmission characteristics up to 2 GHz - Sectional specification
English language
17 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 61156-10 ®
Edition 1.0 2016-04
INTERNATIONAL
STANDARD
Multicore and symmetrical pair/quad cables for digital communications –
Part 10: Cables for cords with transmission characteristics up to 2 GHz –
Sectional specification
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC 61156-10 ®
Edition 1.0 2016-04
INTERNATIONAL
STANDARD
Multicore and symmetrical pair/quad cables for digital communications –

Part 10: Cables for cords with transmission characteristics up to 2 GHz –

Sectional specification
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.20 ISBN 978-2-8322-3351-1

– 2 – IEC 61156-10:2016 © IEC 2016
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references. 6
3 Terms and definitions . 7
4 Installation considerations. 7
5 Materials and cable construction . 7
6 Characteristics and requirements . 7
6.1 General remarks . 7
6.2 Electrical characteristics and tests . 8
6.2.1 Conductor resistance . 8
6.2.2 Resistance unbalance . 8
6.2.3 Dielectric strength . 8
6.2.4 Insulation resistance . 8
6.2.5 Mutual capacitance . 8
6.2.6 Capacitance unbalance . 8
6.2.7 Transfer impedance . 8
6.2.8 Coupling attenuation . 8
6.2.9 Current-carrying capacity . 9
6.3 Transmission characteristics . 9
6.3.1 Velocity of propagation (phase velocity) . 9
6.3.2 Phase delay and differential delay (delay skew) . 9
6.3.3 Attenuation (α) . 9
6.3.4 Unbalance attenuation (TCL) . 10
6.3.5 Near-end crosstalk (NEXT) . 10
6.3.6 Far-end crosstalk (ACR-F) . 11
6.3.7 Alien (exogenous) near-end crosstalk (ANEXT) . 11
6.3.8 Alien (exogenous) far-end crosstalk (AFEXT). 12
6.3.9 Alien (exogenous) crosstalk of bundled cables . 12
6.3.10 Impedance . 12
6.3.11 Return loss (RL) . 12
6.4 Mechanical and dimensional characteristics and requirements . 13
6.4.1 Dimensional requirements . 13
6.4.2 Elongation at break of the conductors . 13
6.4.3 Tensile strength of the insulation . 13
6.4.4 Elongation at break of the insulation . 13
6.4.5 Adhesion of the insulation to the conductor . 13
6.4.6 Elongation at break of the sheath . 13
6.4.7 Tensile strength of the sheath . 13
6.4.8 Crush test of the cable . 13
6.4.9 Impact test of the cable . 13
6.4.10 Bending under tension . 13
6.4.11 Repeated bending of the cable . 13
6.4.12 Tensile performance of the cable . 14
6.4.13 Shock-test requirements of the cable . 14
6.4.14 Bump-test requirements of the cable . 14
6.4.15 Vibration-test requirements of a cable . 14

6.5 Environmental characteristics . 14
6.5.1 Shrinkage of insulation . 14
6.5.2 Wrapping test of insulation after thermal ageing . 14
6.5.3 Bending test of insulation at low temperature . 14
6.5.4 Elongation at break of the sheath after ageing . 14
6.5.5 Tensile strength of the sheath after ageing . 14
6.5.6 Sheath pressure test at high temperature . 14
6.5.7 Cold bend test of the cable . 14
6.5.8 Heat shock test . 14
6.5.9 Damp heat steady state. 14
6.5.10 Solar radiation (UV test) . 14
6.5.11 Solvents and contaminating fluids. 15
6.5.12 Salt mist and sulphur dioxide . 15
6.5.13 Water immersion . 15
6.5.14 Hygroscopicity . 15
6.5.15 Wicking . 15
6.5.16 Flame propagation characteristics of a single cable . 15
6.5.17 Flame propagation characteristics of bunched cables. 15
6.5.18 Halogen gas evolution . 15
6.5.19 Smoke generation . 15
6.5.20 Toxic gas emission . 15
6.5.21 Integrated fire test . 15
7 Bundled cables requirements . 15
8 Introduction to the blank detail specification . 16
Bibliography . 17

Table 1 – Coupling attenuation . 9
Table 2 – Attenuation equation constants . 10
Table 3 – TCL requirements . 10
Table 4 – ELTCTL requirements . 10
Table 5 – NEXT and PS NEXT requirements . 11
Table 6 – ACR-F and PS ACR-F requirements . 11
Table 7 – PS ANEXT requirements . 11
Table 8 – PS AACR-F requirements . 12
Table 9 – RL requirements . 12

– 4 – IEC 61156-10:2016 © IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES
FOR DIGITAL COMMUNICATIONS –
Part 10: Cables for cords with transmission characteristics
up to 2 GHz – Sectional specification

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure tha
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.