Ships and marine technology -- Marine cranes -- Test specifications and procedures

ISO 19356:2016 describes the required tests and the testing procedures for marine cranes of metal construction. ISO 19356:2016 is applicable to the following types of marine cranes: - deck cranes mounted on ships for handling cargo or containers in harbour or sheltered water conditions; - floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions; - engine room cranes, provision cranes, etc. mounted on ships (including floating docks) for handling equipment and stores in harbour conditions. NOTE Marine cranes in other types can refer to this document. ISO 19356:2016 does not apply to the following: - minimum ambient operating temperatures below −20 °C; - maximum ambient operating temperatures above +45 °C; - loads from accidents or collisions; - lifting operations below sea level; - transport, assembly, dismantling and decommissioning of cranes; - lifting accessories, i.e. any item between the crane and the load; - lifting operations involving more than one crane; - hand-powered cranes; - emergency rescue operations; - shore-side cargo handling cranes; - portable cranes on board; - lifting appliances for lifeboats, liferafts accommodation ladders, and pilot ladders; - launching appliances for survival craft and rescue boats; - gangways, accommodation and pilot ladders and their handling appliances. Cranes defined in this document are intended to comply with the requirements of class societies and flag states. It is also intended that reference be made to ILO and particularly the convention No. 152. Applicable regulations are those issued by the responsible classification societies and it is intended that national authorities be complied with.

Navires et technologie maritime -- Grues maritimes -- Spécifications et procédures de test

General Information

Status
Published
Publication Date
20-Sep-2016
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jul-2021
Ref Project

Buy Standard

Standard
ISO 19356:2016 - Ships and marine technology -- Marine cranes -- Test specifications and procedures
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 19356:2016 - Ships and marine technology -- Marine cranes -- Test specifications and procedures
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 19356
First edition
2016-09-15
Ships and marine technology —
Marine cranes — Test specifications
and procedures
Navires et technologie maritime — Grues maritimes — Spécifications
et procédures de test
Reference number
ISO 19356:2016(E)
ISO 2016
---------------------- Page: 1 ----------------------
ISO 19356:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 19356:2016(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 2

3 Terms and definitions ..................................................................................................................................................................................... 2

4 Test specification and procedure requirements ................................................................................................................. 2

4.1 General requirements ....................................................................................................................................................................... 2

4.2 Functional test ......................................................................................................................................................................................... 2

4.2.1 General...................................................................................................................................................................................... 2

4.2.2 Check items before functional test ................................................................................................................... 3

4.2.3 Functional test items .................................................................................................................................................... 3

4.2.4 Check items after functional test ....................................................................................................................... 3

4.3 Bench test .................................................................................................................................................................................................... 3

4.3.1 General...................................................................................................................................................................................... 3

4.3.2 Pre-test check ..................................................................................................................................................................... 3

4.3.3 Bench test items ............................................................................................................................................................... 4

4.4 Inclination test ........................................................................................................................................................................................ 5

4.5 Other tests ................................................................................................................................................................................................... 5

Bibliography ................................................................................................................................................................................................................................ 6

© ISO 2016 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 19356:2016(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,

as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the

Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.

The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee

SC 4, Outfitting and deck machinery.
iv © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 19356:2016(E)
Ships and marine technology — Marine cranes — Test
specifications and procedures
1 Scope

This document describes the required tests and the testing procedures for marine cranes of metal

construction.
This document is applicable to the following types of marine cranes:

— deck cranes mounted on ships for handling cargo or containers in harbour or sheltered water

conditions;

— floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions;

— engine room cranes, provision cranes, etc. mounted on ships (including floating docks) for handling

equipment and stores in harbour conditions.
NOTE Marine cranes in other types can refer to this document.
This document does not apply to the following:
— minimum ambient operating temperatures below −20 °C;
— maximum ambient operating temperatures above +45 °C;
— loads from accidents or collisions;
— lifting operations below sea level;
— transport, assembly, dismantling and decommissioning of cranes;
— lifting accessories, i.e. any item between the crane and the load;
— lifting operations involving more than one crane;
— hand-powered cranes;
— emergency rescue operations;
— shore-side cargo handling cranes;
— portable cranes on board;

— lifting appliances for lifeboats, liferafts accommodation ladders, and pilot ladders;

— launching appliances for survival craft and rescue boats;
— gangways, accommodation and pilot ladders and their handling appliances.

Cranes defined in this document are intended to comply with the requirements of class societies and

flag states. It is also intended that reference be made to ILO and particularly the convention No. 152.

...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 19356
ISO/TC 8/SC 4 Secretariat: SAC
Voting begins on: Voting terminates on:
2015-06-30 2015-09-30
Ships and Marine Technology — Marine cranes — Test
specification and procedures

Navires et technologie maritime — Grues maritimes — Spécification de test et procédures

ICS: 47.020.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19356:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015
---------------------- Page: 1 ----------------------
ISO/DIS 19356:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 19356:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Test specification and procedure requirements ................................................................................................................. 2

4.1 General requirements ....................................................................................................................................................................... 2

4.2 Functional test ......................................................................................................................................................................................... 2

4.3 Bench test .................................................................................................................................................................................................... 3

4.4 Inclination test ........................................................................................................................................................................................ 4

4.5 Other tests ................................................................................................................................................................................................... 4

© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/DIS 19356:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any

patent rights identified during the development of the document will be in the Introduction and/or on

the ISO list of patent declarations received. www.iso.org/patents

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers

to Trade (TBT), see the following URL: Foreword - Supplementary information

The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee

SC 4, Outfitting and Deck Machinery.
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 19356:2015(E)
Ships and Marine Technology — Marine cranes — Test
specification and procedures
1 Scope

This International Standard specifies the requirements for the test specification and procedures of

marine cranes.

1.1 Marine cranes applicable to this International Standard include the following types of cranes:

Deck cranes mounted on ships for handling cargo or containers in harbour conditions;

Floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions;

Engine room cranes and provision cranes etc. mounted on ships (including floating docks) for handling

equipment and stores in harbour conditions.
1.2 This International Standard does not apply to:
Transport, assembly, dismantling and decommissioning of cranes,
Lifting accessories, i.e. any item between the crane and the load,
Lifting operations involving more than one crane,
Hand powered cranes,
Emergency rescue operations (except training),
Shore-side cargo handling cranes,
Portable cranes on board,

Lifting appliances for lifeboats, liferafts accommodation ladders and pilot ladders.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edit

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.