ISO 1436-1:2001

Rubber hoses and hose assemblies — Wire-braid-reinforced hydraulic types — Specification — Part 1: Oil-based fluid applications

Tuyaux et flexibles en caoutchouc — Types hydrauliques avec armature de fils métalliques tressés — Spécifications — Partie 1: Applications pour fluide à base d'huile

Gumene cevi in cevni priključki – S pletenimi žicami okrepljene hidravlične cevi - Specifikacija - 1. del: Uporaba za oljne tekočine

General Information

• Status: Withdrawn
• Publication Date: 29-Aug-2001
• Withdrawal Date: 29-Aug-2001
• ICS: 23.100.40 - Piping and couplings
• ICS: 83.140.40 - Hoses
• Technical Committee: ISO/TC 45/SC 1 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: ISO/TC 45/SC 1/WG 3 - Hydraulic hoses
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 24-Apr-2009
• Ref Project: SIST ISO 1436-1:2004 - Rubber hoses and hose assemblies -- Wire-braid-reinforced hydraulic types -- Specification -- Part 1: Oil-based fluid applications

Relations

• Revised: ISO 1436:2009 - Rubber hoses and hose assemblies — Wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification
• Effective Date: 15-Apr-2008
• Revises: ISO 1436:1991 - Rubber hoses and hose assemblies — Wire-reinforced hydraulic type — Specification
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1436-1
First edition
2001-09-01
Rubber hoses and hose assemblies —
Wire-braid-reinforced hydraulic types —
Specification —
Part 1:
Oil-based fluid applications
Tuyaux et flexibles en caoutchouc — Types hydrauliques avec armature de
fils métalliques tressés — Spécifications —
Partie 1: Applications pour fluide à base d'huile
Reference number
ISO 1436-1:2001(E)
©
ISO 2001

---------------------- Page: 1 ----------------------
ISO 1436-1:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 1436-1:2001(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Classification.2
4 Materials and construction.2
4.1 Hoses .2
4.2 Hose assemblies.2
5 Dimensions.2
5.1 Diameters and concentricity.2
5.2 Length.4
6 Requirements.4
6.1 Hydrostatic requirements .4
6.2 Minimum bend radius.5
6.3 Resistance to impulse.6
6.4 Leakage of hose assemblies .6
6.5 Cold flexibility .6
6.6 Adhesion between components.6
6.7 Vacuum resistance .7
6.8 Abrasion resistance .7
6.9 Fluid resistance.7
6.10 Ozone resistance .8
7 Designation .8
8 Marking .8
8.1 Hoses .8
8.2 Hose assemblies.8
Annex A (informative) Recommendations for lengths of supplied hoses and hose assemblies.9
A.1 Hoses .9
A.2 Hose assemblies.9
Bibliography.10
© ISO 2001 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 1436-1:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 1436 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 1436-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Hoses (rubber and plastics).
Together with ISO 1436-2 (in preparation), this part of ISO 1436 cancels and replaces ISO 1436:1991, which has
been technically revised.
ISO 1436 consists of the following parts, under the general title Rubber hoses and hose assemblies — Wire-braid-
reinforced hydraulic types — Specification:
� Part 1: Oil-based fluid applications
� Part 2: Water-based fluid applications
Annex A of this part of ISO 1436 is for information only.
iv © ISO 2001 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 1436-1:2001(E)
Rubber hoses and hose assemblies — Wire-braid-reinforced
hydraulic types — Specification —
Part 1:
Oil-based fluid applications
1 Scope
This part of ISO 1436 specifies requirements for eight types of wire-braid-reinforced hoses and hose assemblies of
nominal bore from 5 to 51. They are suitable for use with hydraulic fluids HH, HL, HM, HR and HV in accordance
with ISO 6743-4 at temperatures ranging from – 40 °C to + 100 °C.
This part of ISO 1436 does not include requirements for end fittings. It is limited to requirements for the
performance of hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose
with the fluid to be used.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 1436. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 1436 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized — Determination of the effect of liquids
ISO 4671, Rubber and plastics hose and hose assemblies — Methods of measurement of dimensions
ISO 4672:1997, Rubber and plastics hoses — Sub-ambient temperature flexibility tests
ISO 6803, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 6945, Rubber hoses — Determination of abrasion resistance of the outer cover
ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of suction resistance
ISO 7326:1991, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8033:1991, Rubber and plastics hose — Determination of adhesion between components
© ISO 2001 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 1436-1:2001(E)
3 Classification
Eight types of hose are specified, distinguished by their construction, working pressure and oil resistance:
� Types 1ST and R1A: hoses with a single braid of wire reinforcement and having a thick cover.
� Types 2ST and R2A: hoses with two braids of wire reinforcement and having a thick cover.
� Types 1SN and R1AT: hoses with a single braid of wire reinforcement and having a thin cover.
� Types 2SN and R2AT: hoses with two braids of wire reinforcement and having a thin cover.
NOTE 1 Types 1SN/R1AT and 2SN/R2AT have the same reinforcement dimensions as types 1ST/R1A and 2ST/R2A,
respectively, except that they have thinner covers designed for assembly with fittings without removal of the cover or a portion of
the cover.
NOTE 2 The pressure ratings of types 1ST and 1SN differ from those of types R1A and R1AT. Similarly, the pressure ratings
of types 2ST and 2SN differ from those of types R2A and R2AT. See Table 3.
NOTE 3 Types R1A, R2A, R1AT and R2AT are not subjected to the vacuum resistance or abrasion resistance tests.
4 Materials and construction
4.1 Hoses
Hoses shall consist of a hydraulic-fluid-resistant rubber lining, one or two layer
...

SLOVENSKI STANDARD
SIST ISO 1436-1:2004
01-januar-2004
*XPHQHFHYLLQFHYQLSULNOMXþNL±6SOHWHQLPLåLFDPLRNUHSOMHQHKLGUDYOLþQHFHYL
6SHFLILNDFLMDGHO8SRUDED]DROMQHWHNRþLQH
Rubber hoses and hose assemblies -- Wire-braid-reinforced hydraulic types --
Specification -- Part 1: Oil-based fluid applications
Tuyaux et flexibles en caoutchouc -- Types hydrauliques avec armature de fils
métalliques tressés -- Spécifications -- Partie 1: Applications pour fluide à base d'huile
Ta slovenski standard je istoveten z: ISO 1436-1:2001
ICS:
83.140.40 Gumene cevi Hoses
SIST ISO 1436-1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 1436-1:2004

---------------------- Page: 2 ----------------------

SIST ISO 1436-1:2004
INTERNATIONAL ISO
STANDARD 1436-1
First edition
2001-09-01
Rubber hoses and hose assemblies —
Wire-braid-reinforced hydraulic types —
Specification —
Part 1:
Oil-based fluid applications
Tuyaux et flexibles en caoutchouc — Types hydrauliques avec armature de
fils métalliques tressés — Spécifications —
Partie 1: Applications pour fluide à base d'huile
Reference number
ISO 1436-1:2001(E)
©
ISO 2001

---------------------- Page: 3 ----------------------

SIST ISO 1436-1:2004
ISO 1436-1:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 1436-1:2004
ISO 1436-1:2001(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Classification.2
4 Materials and construction.2
4.1 Hoses .2
4.2 Hose assemblies.2
5 Dimensions.2
5.1 Diameters and concentricity.2
5.2 Length.4
6 Requirements.4
6.1 Hydrostatic requirements .4
6.2 Minimum bend radius.5
6.3 Resistance to impulse.6
6.4 Leakage of hose assemblies .6
6.5 Cold flexibility .6
6.6 Adhesion between components.6
6.7 Vacuum resistance .7
6.8 Abrasion resistance .7
6.9 Fluid resistance.7
6.10 Ozone resistance .8
7 Designation .8
8 Marking .8
8.1 Hoses .8
8.2 Hose assemblies.8
Annex A (informative) Recommendations for lengths of supplied hoses and hose assemblies.9
A.1 Hoses .9
A.2 Hose assemblies.9
Bibliography.10
© ISO 2001 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 1436-1:2004
ISO 1436-1:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 1436 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 1436-1 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Hoses (rubber and plastics).
Together with ISO 1436-2 (in preparation), this part of ISO 1436 cancels and replaces ISO 1436:1991, which has
been technically revised.
ISO 1436 consists of the following parts, under the general title Rubber hoses and hose assemblies — Wire-braid-
reinforced hydraulic types — Specification:
� Part 1: Oil-based fluid applications
� Part 2: Water-based fluid applications
Annex A of this part of ISO 1436 is for information only.
iv © ISO 2001 – All rights reserved

---------------------- Page: 6 ----------------------

SIST ISO 1436-1:2004
INTERNATIONAL STANDARD ISO 1436-1:2001(E)
Rubber hoses and hose assemblies — Wire-braid-reinforced
hydraulic types — Specification —
Part 1:
Oil-based fluid applications
1 Scope
This part of ISO 1436 specifies requirements for eight types of wire-braid-reinforced hoses and hose assemblies of
nominal bore from 5 to 51. They are suitable for use with hydraulic fluids HH, HL, HM, HR and HV in accordance
with ISO 6743-4 at temperatures ranging from – 40 °C to + 100 °C.
This part of ISO 1436 does not include requirements for end fittings. It is limited to requirements for the
performance of hoses and hose assemblies.
NOTE It is the responsibility of the user, in consultation with the hose manufacturer, to establish compatibility of the hose
with the fluid to be used.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 1436. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 1436 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized — Determination of the effect of liquids
ISO 4671, Rubber and plastics hose and hose assemblies — Methods of measurement of dimensions
ISO 4672:1997, Rubber and plastics hoses — Sub-ambient temperature flexibility tests
ISO 6803, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 6945, Rubber hoses — Determination of abrasion resistance of the outer cover
ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of suction resistance
ISO 7326:1991, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8033:1991, Rubber and plastics hose — Determination of adhesion between components
© ISO 2001 – All rights reserved 1

---------------------- Page: 7 ----------------------

SIST ISO 1436-1:2004
ISO 1436-1:2001(E)
3 Classification
Eight types of hose are specified, distinguished by their construction, working pressure and oil resistance:
� Types 1ST and R1A: hoses with a single braid of wire reinforcement and having a thick cover.
� Types 2ST and R2A: hoses with two braids of wire reinforcement and having a thick cover.
� Types 1SN and R1AT: hoses with a single braid of wire reinforcement and having a thin cover.
� Types 2SN and R2AT: hoses with two braids of wire reinforcement and having a thin cover.
NOTE 1 Types 1SN/R1AT and 2SN/R2AT have the same reinforcement dimensions as types 1ST/R1A and 2ST/R2A,
respectively, except that they have thinner covers designed for assembly with fittings witho
...

OSIST ISO 1436-1:2003SLOVENSKIdecember 2003
PREDSTANDARDGumene cevi in cevni priključki – S pletenimi žicami okrepljene hidravlične cevi - Specifikacija - 1. del: Uporaba za oljne tekočineRubber hoses and hose assemblies - Wire-braid-reinforced
hydraulic types - Specification - Part 1: Oil-based fluid
applications©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaOSIST ISO 1436-1:2003(en)ICS23.100.40; 83.140.40







ReferencenumberISO1436-1:2001(E)©ISO2001INTERNATIONALSTANDARDISO1436-1Firstedition2001-09-01Rubberhosesandhoseassemblies—Wire-braid-reinforcedhydraulictypes—Specification—Part1:Oil-basedfluidapplicationsTuyauxetflexiblesencaoutchouc—Typeshydrauliquesavecarmaturedefilsmétalliquestressés—Spécifications—Partie1:Applicationspourfluideàbased'huile



ISO1436-1:2001(E)PDFdisclaimerThisPDFfilemaycontainembeddedtypefaces.InaccordancewithAdobe'slicensingpolicy,thisfilemaybeprintedorviewedbutshallnotbeeditedunlessthetypefaceswhichareembeddedarelicensedtoandinstalledonthecomputerperformingtheediting.Indownloadingthisfile,partiesacceptthereintheresponsibilityofnotinfringingAdobe'slicensingpolicy.TheISOCentralSecretariatacceptsnoliabilityinthisarea.AdobeisatrademarkofAdobeSystemsIncorporated.DetailsofthesoftwareproductsusedtocreatethisPDFfilecanbefoundintheGeneralInforelativetothefile;thePDF-creationparameterswereoptimizedforprinting.EverycarehasbeentakentoensurethatthefileissuitableforusebyISOmemberbodies.Intheunlikelyeventthataproblemrelatingtoitisfound,pleaseinformtheCentralSecretariatattheaddressgivenbelow.©ISO2001Allrightsreserved.Unlessotherwisespecified,nopartofthispublicationmaybereproducedorutilizedinanyformorbyanymeans,electronicormechanical,includingphotocopyingandmicrofilm,withoutpermissioninwritingfromeitherISOattheaddressbeloworISO'smemberbodyinthecountryoftherequester.ISOcopyrightofficeCasepostal[e-mail]©ISO2001–Allrightsreserved



ISO1436-1:2001(E)©ISO2001–AllrightsreservediiiContentsPageForeword.iv1Scope.12Normativereferences.13Classification.24Materialsandconstruction.24.1Hoses.24.2Hoseassemblies.25Dimensions.25.1Diametersandconcentricity.25.2Length.46Requirements.46.1Hydrostaticrequirements.46.2Minimumbendradius.56.3Resistancetoimpulse.66.4Leakageofhoseassemblies.66.5Coldflexibility.66.6Adhesionbetweencomponents.66.7Vacuumresistance.76.8Abrasionresistance.76.9Fluidresistance.76.10Ozoneresistance.87Designation.88Marking.88.1Hoses.88.2Hoseassemblies.8AnnexA(informative)Recommendationsforlengthsofsuppliedhosesandhoseassemblies.9A.1Hoses.9A.2Hoseassemblies.9Bibliography.10



ISO1436-1:2001(E)iv©ISO2001–AllrightsreservedForewordISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISOmemberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhastherighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,inliaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnicalCommission(IEC)onallmattersofelectrotechnicalstandardization.InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3.DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting.PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote.AttentionisdrawntothepossibilitythatsomeoftheelementsofthispartofISO1436maybethesubjectofpatentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights.InternationalStandardISO1436-1waspreparedbyTechnicalCommitteeISO/TC45,Rubberandrubberproducts,SubcommitteeSC1,Hoses(rubberandplastics).TogetherwithISO1436-2(inpreparation),thispartofISO1436cancelsandreplacesISO1436:1991,whichhasbeentechnicallyrevised.ISO1436consistsofthefollowingparts,underthegeneraltitleRubberhosesandhoseassemblies—Wire-braid-reinforcedhydraulictypes—Specification:Part1:Oil-basedfluidapplicationsPart2:Water-basedfluidapplicationsAnnexAofthispartofISO1436isforinformationonly.



INTERNATIONALSTANDARDISO1436-1:2001(E)©ISO2001–Allrightsreserved1Rubberhosesandhoseassemblies—Wire-braid-reinforcedhydraulictypes—Specification—Part1:Oil-basedfluidapplications1ScopeThispartofISO1436specifiesrequirementsforeighttypesofwire-braid-reinforcedhosesandhoseassembliesofnominalborefrom5to51.TheyaresuitableforusewithhydraulicfluidsHH,HL,HM,HRandHVinaccordancewithISO6743-4attemperaturesrangingfrom–40°Cto+100°C.ThispartofISO1436doesnotincluderequirementsforendfittings.Itislimitedtorequirementsfortheperformanceofhosesandhoseassemblies.NOTEItistheresponsibilityoftheuser,inconsultationwiththehosemanufacturer,toestablishcompatibilityofthehosewiththefluidtobeused.2NormativereferencesThefollowingnormativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthispartofISO1436.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdonotapply.However,partiestoagreementsbasedonthispartofISO1436areencouragedtoinvestigatethepossibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.Forundatedreferences,thelatesteditionofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersofcurrentlyvalidInternationalStandards.ISO1402,Rubberandplasticshosesandhoseassemblies—HydrostatictestingISO1817,Rubber,vulcanized—DeterminationoftheeffectofliquidsISO4671,Rubberandplasticshoseandhoseassemblies—MethodsofmeasurementofdimensionsISO4672:1997,Rubberandplasticshoses—Sub-ambienttemperatureflexibilitytestsISO6803,Rubberorplasticshosesandhoseassemblies—Hydraulic-pressureimpulsetestwithoutflexingISO6945,Rubberhoses—DeterminationofabrasionresistanceoftheoutercoverISO7233,Rubberandplasticshosesandhoseassemblies—DeterminationofsuctionresistanceISO7326:1991,Rubberandplasticshoses—AssessmentofozoneresistanceunderstaticconditionsISO8033:1991,Rubberandplasticshose—Determinationofadhesionbetweencomponents



ISO1436-1:2001(E)2©ISO2001–Allrightsreserved3ClassificationE
...