ISO 11479-1:2011
(Main)Glass in building — Coated glass — Part 1: Physical defects
Glass in building — Coated glass — Part 1: Physical defects
This part of ISO 11479 specifies optical quality requirements for coatings applied to glass using either pyrolytic, sol-gel or vacuum (sputtering) deposition methods for use in building glazing. More specifically, this part of ISO 11479 relates to low-e and solar-control coated glass. This part of ISO 11479 is not applicable to patterned or other optically distorting glass.
Verre dans la construction — Verre à couche — Partie 1: Défauts physiques
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 11479-1
First edition
2011-10-01
Glass in building — Coated glass —
Part 1:
Physical defects
Verre dans la construction — Verre à couche — Partie 1: Défauts
physiques
Reference number
ISO 11479-1:2011(E)
©
ISO 2011
---------------------- Page: 1 ----------------------
ISO 11479-1:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 11479-1:2011(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Terms and definitions . 1
2.1 Basic definitions . 1
2.2 Definition of physical defects . 2
3 Physical defects . 3
3.1 General . 3
3.2 Detection of defects . 3
3.3 Conditions of examination . 3
3.4 Punctual defects . 5
3.5 Acceptance criteria for coated glass defects . 6
Bibliography . 7
© ISO 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 11479-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11479-1 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee SC 1,
Product considerations.
ISO 11479 consists of the following parts, under the general title Glass in building — Coated glass:
— Part 1: Physical defects
— Part 2: Colour of façade
iv © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 11479-1:2011(E)
Glass in building — Coated glass —
Part 1:
Physical defects
1 Scope
This part of ISO 11479 specifies optical quality requirements for coatings applied to glass using either pyrolytic,
sol-gel o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.