ISO 15142-2:2003

Implants for surgery — Metal intramedullary nailing systems — Part 2: Locking components

ISO 15142-2:2003 specifies metallic medical devices used for the temporary intramedullary stabilization of long bones by surgical implantation, classifying and giving requirements for the locking components of intramedullary nails. It is applicable to all metal intramedullary fixation devices used for temporary fixation of long bones in the human body, except unlockable nails.

Implants chirurgicaux — Systèmes d'enclouage intramédullaire en métal — Partie 2: Éléments de fixation

General Information

• Status: Published
• Publication Date: 11-Aug-2003
• ICS: 11.040.40 - Implants for surgery, prosthetics and orthotics
• Technical Committee: ISO/TC 150/SC 5 - Osteosynthesis and spinal devices
• Drafting Committee: ISO/TC 150/SC 5 - Osteosynthesis and spinal devices
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 04-May-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15142-2
First edition
2003-08-01


Implants for surgery — Metal
intramedullary nailing systems —
Part 2:
Locking components
Implants chirurgicaux — Systèmes d'enclouage intramédullaire en
métal —
Partie 2: Éléments de fixation




Reference number
ISO 15142-2:2003(E)
©
ISO 2003

---------------------- Page: 1 ----------------------
ISO 15142-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 2 ----------------------
ISO 15142-2:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Classification and designation . 1
5 Materials. 2
6 Surface requirements. 2
7 Marking. 2
8 Product labelling. 2
9 Drive connections for insertion and removal of locking components. 2
Bibliography . 3


© ISO 2003 — All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 15142-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15142-2 was prepared by Technical Committee ISO/TC 150, Implants for surgery, Subcommittee SC 5,
Osteosynthesis and spinal devices.
ISO 15142 consists of the following parts, under the general title Implants for surgery — Metal intramedullary
nailing systems:
 Part 1: Intr
...