Footwear sizing — Mondopoint system of sizing and marking

This document specifies a method of designation and marking of footwear size called Mondopoint, based on defined measurements of the foot that the footwear is intended to fit. This document is applicable to all types of footwear.

Pointure des chaussures — Système Mondopoint de mesure et de marquage

General Information

Status
Published
Publication Date
02-Jul-2019
Current Stage
6060 - International Standard published
Start Date
31-May-2019
Due Date
07-Jun-2019
Completion Date
03-Jul-2019
Ref Project

Relations

Buy Standard

Standard
REDLINE ISO 9407:2019 - Footwear sizing — Mondopoint system of sizing and marking Released:7/3/2019
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 9407:2019 - Footwear sizing -- Mondopoint system of sizing and marking
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

ISO/TC 137
Deleted: 04
Date:  2019-06
Deleted: /PRF
ISO 9407:2019(E)
ISO/TC 137
Secretariat:  SABS/SAC
Footwear sizing — Mondopoint system of sizing and marking
Pointure des chaussures — Système Mondopoint de mesure et de marquage
© ISO 2019 – All rights reserved i

---------------------- Page: 1 ----------------------
ISO 9407:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no
part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet, without
prior written permission. Permission can be requested from either ISO at the address below or ISO's
member body in the country of the requester.
ISO Copyright Office
CP 401 • CH‐1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Fax: + 41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2019 – All rights reserved
1

---------------------- Page: 2 ----------------------
ISO 9407:2019(E)
Contents
Contents . 2
Foreword . 3
Introduction . 4
1  Scope . 1
2  Normative references . 1
3  Terms and definitions. 1
........................................................................................ 2
Figure 1 — Foot length measured along the inside tangent .
Figure 2 — Joint position of the foot . 3
Figure 3 — Linear width and joint girth of the foot at the joint position . 3
4  Fundamental characteristics of the Mondopoint sizing system . 3
5  Method of expressing Mondopoint sizing . 4
6  Footwear marking . 4
6.1  Format . 4
6.2  Location of the marking . 4
6.2.1  On the shoe . 4
6.2.2  On the packaging . 4
6.3  Form of the marking . 4
7  Transition from other shoe size systems . 4
Bibliography . 5

© ISO 2019 – All rights reserved
2

---------------------- Page: 3 ----------------------
ISO 9407:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non‐governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on the
ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT)
see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 137, Footwear sizing designations and
marking systems.
This second edition cancels and replaces the first edition (ISO 9407:1991), which has been technically
revised. The main changes compared with the previous edition are as follows:
— references have been added and alignment has been made to ISO/TS 19407 and ISO/TS 19408;
— new pictograms have been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
© ISO 2019 – All rights reserved
3

---------------------- Page: 4 ----------------------
ISO 9407:2019(E)
Introduction
Mondopoint offers a simple and universal solution to the problem of communicating footwear sizing to
customers in the global market, overcoming the present confusion resulting from labelling with multiple
size systems. Online and mail‐order customers are commonly encouraged to measure and report their foot
length as a guide to shoe size selection. Mondopoint lends itself directly to this approach.
The last maker will use whatever last dimensions they consider necessary to produce the required Deleted: Of course, size (foot length) is
not the only factor that influences
footwear fitting properties, taking into account factors such as footwear type and style, modulus/stretch
customer choice.
characteristics of the upper materials being used, and the thickness of hose appropriate to the type of
Deleted: would
footwear.
Deleted: were considered
The length grading interval, which is the difference between adjacent whole shoe sizes (as defined in
ISO/TS 19408:2015, 2.1.9], used by manufacturers aligning to the Mondopoint system, is normally 5 mm,
although 7,5 mm is sometimes used in specialist footwear applications.
Some manufacturers, particularly in the Far East, use the Mondopoint sizing system but do not necessarily
label it as Mondopoint, as shown in Table 1, for example.
Table 1 — Example of a sizing system
Shoe mm CN JP
...

INTERNATIONAL ISO
STANDARD 9407
Second edition
2019-06
Footwear sizing — Mondopoint system
of sizing and marking
Pointure des chaussures — Système Mondopoint de mesure et de
marquage
Reference number
ISO 9407:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 9407:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9407:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Fundamental characteristics of the Mondopoint sizing system . 4
5 Method of expressing Mondopoint sizing . 4
6 Footwear marking . 4
6.1 Format . 4
6.2 Location of the marking . 4
6.2.1 On the shoe . 4
6.2.2 On the packaging . 4
6.3 Form of the marking . 4
7 Transition from other shoe size systems . 5
Bibliography . 6
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 9407:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 137, Footwear sizing designations and
marking systems.
This second edition cancels and replaces the first edition (ISO 9407:1991), which has been technically
revised. The main changes compared with the previous edition are as follows:
— references have been added and alignment has been made to ISO/TS 19407 and ISO/TS 19408;
— new pictograms have been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 9407:2019(E)

Introduction
Mondopoint offers a simple and universal solution to the problem of communicating footwear sizing to
customers in the global market, overcoming the present confusion resulting from labelling with multiple
size systems. Online and mail-order customers are commonly encouraged to measure and report their
foot length as a guide to shoe size selection. Mondopoint lends itself directly to this approach.
The last maker will use whatever last dimensions they consider necessary to produce the required
footwear fitting properties, taking into account factors such as footwear type and style, modulus/
stretch characteristics of the upper materials being used, and the thickness of hose appropriate to the
type of footwear.
The length grading interval, which is the difference between adjacent whole shoe sizes (as defined
in ISO/TS 19408:2015, 2.1.9], used by manufacturers aligning to the Mondopoint system, is normally
5 mm, although 7,5 mm is sometimes used in specialist footwear applications.
Some manufacturers, particularly in the Far East, use the Mondopoint sizing system but do not
necessarily label it as Mondopoint, as shown in Table 1, for example.
Table 1 — Example of a sizing system
Shoe mm CN JP Korea
1 260 260 260 260
2 265 265 265 265
Some manufacturers express size in centimetres rather than millimetres (e.g. 26 in place of 260 or
26,5 in place of 265). Other manufacturers give size markings that relate to last length rather than foot
length. Neither of these expressions of size conform to this document.
Regarding the line
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.