ISO 6363-5:2012

Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 5: Drawn square and hexagonal bars and wires — Tolerances on form and dimensions

ISO 6363-5:2012 specifies the tolerances on form and dimensions of wrought aluminium and aluminium alloy drawn square and hexagonal bars and wires with widths across flats up to and including 100 mm.

Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 5: Barres carrées et hexagonales et fils étirés — Tolérances sur forme et dimensions

General Information

• Status: Withdrawn
• Publication Date: 11-Jul-2012
• ICS: 77.150.10 - Aluminium products
• Technical Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Drafting Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 01-Jul-2022

Relations

• Revised: ISO 6363-5:2022 - Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 5: Tolerances on form and dimensions for drawn square and hexagonal bars and wires
• Effective Date: 23-Apr-2020
• Revises: ISO 6363-5:1992 - Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes — Part 5: Drawn square and hexagonal bars — Tolerances on form and dimensions
• Effective Date: 23-May-2009

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6363-5
Second edition
2012-07-15
Wrought aluminium and aluminium
alloys — Cold-drawn rods/bars, tubes
and wires —
Part 5:
Drawn square and hexagonal bars
and wires — Tolerances on form and
dimensions
Aluminium et alliages d’aluminium corroyés — Barres, tubes et fils
étirés à froid —
Partie 5: Barres carrées et hexagonales et fils étirés — Tolérances sur
forme et dimensions
Reference number
ISO 6363-5:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 6363-5:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6363-5:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Tolerances on form and dimensions . 1
4.1 Tolerances on width across flats . 1
4.2 Fixed-length tolerances . 2
4.3 Squareness of cut ends . 3
4.4 Corner radii . 3
4.5 Form tolerances . 3
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6363-5:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6363-5 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee
SC 6, Wrought aluminium and aluminium alloys.
This second edition cancels and replaces the first edition (ISO 6363-5:1992), which has been technically revised.
ISO 6363 consists of the following parts, under the general title Wrought aluminium and aluminium alloys —
Cold-drawn rods/bars, tubes and wires:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Mechanical properties
— Part 3: Drawn round bars and wires — Tolerances on form and dimensions (symmetric plus and minus
tolerances on diameter)
— Part 4: Drawn rectangular bars and wires — Tolerances on form and dimensions
— Part 5: Drawn square and hexagonal bars and wires — Tolerances on form and dimensions
— Part 6: Drawn round tubes — Tolerances on form and dimensions
iv © ISO 2012 – All rights reserved

-----------------
...