iTeh Standards logo
EURUSD
Your shopping cart is empty.
ISO

ISO 10639:2004/Amd 1:2011

(Amendment)

Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1

Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1

Systèmes de canalisation en matières plastiques pour l'alimentation en eau avec ou sans pression — Systèmes en plastiques thermodurcissables renforcés de verre (PRV) à base de résine de polyester non saturé (UP) — Amendement 1

General Information

Status
Withdrawn
Publication Date
16-Feb-2011
Withdrawal Date
16-Feb-2011
ICS
23.040.20 - Plastics pipes
91.140.60 - Water supply systems
93.025 - External water conveyance systems
Technical Committee
ISO/TC 138/SC 6 - Reinforced plastics pipes and fittings for all applications
Drafting Committee
ISO/TC 138/SC 6/WG 3 - Specifications for pipe systems
Current Stage
9599 - Withdrawal of International Standard
Start Date
12-Oct-2017
Completion Date
13-Dec-2025
Ref Project

Relations

Amends
ISO 10639:2004 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
Effective Date
06-Jun-2022
Revised
ISO 10639:2017 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
Effective Date
02-Nov-2013
Child
ISO 10639:2004 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
Effective Date
31-Jul-2008
ISO 10639:2004/Amd 1:2011ISO 10639:2004/Amd 1:2011
PreviousNext
Standard
ISO 10639:2004/Amd 1:2011
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Frequently Asked Questions

ISO 10639:2004/Amd 1:2011 is a standard published by the International Organization for Standardization (ISO). Its full title is "Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1". This standard covers: Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1

Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1

ISO 10639:2004/Amd 1:2011 is classified under the following ICS (International Classification for Standards) categories: 23.040.20 - Plastics pipes; 91.140.60 - Water supply systems; 93.025 - External water conveyance systems. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO 10639:2004/Amd 1:2011 has the following relationships with other standards: It is inter standard links to ISO 10639:2004, ISO 10639:2017; is excused to ISO 10639:2004. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

You can purchase ISO 10639:2004/Amd 1:2011 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.

Standards Content (Sample)


INTERNATIONAL ISO
STANDARD 10639
First edition
2004-02-01
AMENDMENT 1
2011-03-01
Plastics piping systems for pressure and
non-pressure water supply — Glass-
reinforced thermosetting plastics (GRP)
systems based on unsaturated polyester
(UP) resin
AMENDMENT 1
Systèmes de canalisation en matières plastiques pour l'alimentation en
eau avec ou sans pression — Systèmes en plastiques
thermodurcissables renforcés de verre (PRV) à base de résine de
polyester non saturé (UP)
AMENDEMENT 1
Reference number
ISO 10639:2004/Amd.1:2011(E)
©
ISO 2011
ISO 10639:2004/Amd.1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 10639:2004/Amd.1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 10639:2004 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings
and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all
applications.
ISO 10639:2004/Amd.1:2011(E)
Plastics piping systems for pressure and non-pressure water
supply — Glass-reinforced thermosetting plastics (GRP)
systems based on unsaturated polyester (UP) resin
AMENDMENT 1
Page 1, Scope
Add the following Note after the first paragraph and renumber other note as Note 2:
NOTE 1 For the purpose of this International Standard, the term polyester resin also includes vinyl-ester resins.
Pages 2 and 3, Normative references
Correct the following dated Normative references into undated references:
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 7432, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the
design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
ISO 7511, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test
methods to prove the leaktightness of the wall under short-term internal pressure
ISO 8483, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test method to prove the
design of bolted flange joints
ISO 8513, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of
longitudinal tensile properties
ISO 8521, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods
for the determination of apparent initial circumferential tensile strength
ISO 8533, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the
design of cemented or wrapped joint
ISO 8639, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness
of flexible joints
ISO 10928, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings —
Methods for regression analysis and their use
Page 16, 4.5.1
Add the following paragraph after the first paragraph:
For routine quality control testing, any measurements shall be taken at the prevailing temperature or, if the
manufacturer requires, at the temperature specified in this clause.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

This May Also Interest You

ISO
ISO 4427-2:2019/Amd 1:2023(Amendment)
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes - Amendment 1
  • Standard
    2 pages
    English language
    sale 15% off
ISO
ISO 22391-2:2009/Amd 1:2020(Amendment)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes - Amendment 1
  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    French language
    sale 15% off
ISO
ISO 4427-5:2019(Main)
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system

This document specifies the characteristics of the fitness for purpose of pipes and/or fittings assemblies made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 The intended uses include sea outfalls, laid in water and pipes suspended below bridges. NOTE 2 This document is intended to be only used by the product manufacturer to assess the performance of components according to ISO 4427‑2 and/or ISO 4427‑3 when joined together under normal and extreme conditions. It is not intended for on-site testing of pipe systems. This document also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE pipes, fittings, their joints and to joints with components of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1]; b) an operating temperature of 20 °C as the reference temperature. NOTE 3 For other operating temperatures, guidance is given in ISO 4427‑1: 2019, Annex A. The ISO 4427 series covers a range of maximum allowable operating pressures and gives requirements concerning colours. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    9 pages
    English language
    sale 15% off
ISO
ISO 4427-2:2019(Main)
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes

This document specifies the pipes made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of: - water for human consumption; - raw water prior to treatment; - drainage and sewerage under pressure; - vacuum sewer systems; - water for other purposes. NOTE 1 The intended uses include sea outfalls, laid in water and pipes suspended below bridges. Pipes complying with this document are not intended for the transport of water intended for human consumption in contaminated soils unless special consideration has been taken. NOTE 2 For example, ISO 21004 provides an alternative solution for use in contaminated soils. See Reference [3] in the Bibliography. This document specifies three types of pipe: - PE pipes (outside diameter dn), including any identification stripes; - PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) where all layers have the same MRS rating; - PE pipes (outside diameter dn) having a peelable and contiguous thermoplastics additional layer on the outside of the pipe ("coated pipe"). This document also specifies the test parameters for the test methods referred to in this document. In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE pipes, their joints and to joints with components made of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1]; b) an operating temperature of 20 °C as the reference temperature. NOTE 3 For other operating temperatures, guidance is given in ISO 4427‑1:2019, Annex A. This document covers a range of maximum allowable operating pressures and gives requirements concerning colours. NOTE 4 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    20 pages
    English language
    sale 15% off
ISO
ISO 4427-1:2019(Main)
Plastics piping systems for water supply and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General

This document specifies the general aspects of polyethylene (PE) compounds for the manufacture of pressure pipes and fittings (mains and service pipes) for buried or above ground applications, intended for the conveyance of: - water for human consumption; - raw water prior to treatment; - drainage and sewerage under pressure; - vacuum sewer systems; - water for other purposes. This document also specifies the test parameters and requirements for the test methods referred to in this document. In conjunction with other parts of the ISO 4427 series, this document is applicable to PE pipes and fittings, their joints and to joints with components made of PE and other materials, intended to be used under the following conditions: a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1]; b) an operating temperature of 20 °C as the reference temperature. NOTE 1 For other operating temperatures, guidance is given in Annex A. The ISO 4427 series covers a range of maximum allowable operating pressures and gives requirements concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    17 pages
    English language
    sale 15% off
ISO
ISO/TR 4191:2014(Main)
Plastics piping systems for water supply - Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) - Guidance for installation
SIST-TP ISO/TR 4191:2018

ISO/TR 4191:2014 gives recommended practices for installation of unplasticized poly(vinyl chloride) (PVC-U) and oriented unplasticized poly(vinyl chloride) (PVC-O) pipes, fittings, valves, and ancillaries when used in piping systems conveying water under pressure. The recommendations are intended to give practical guidance of design and installation of piping systems incorporating pipes, fittings, valves, and ancillary equipment made from PVC materials and used for the following purposes: water mains and services buried in ground, waste water under pressure, and conveyance of water above ground for both outside and inside buildings, for the supply of water under pressure at approximately 20 °C (cold water) intended for human consumption and for general purposes. ISO/TR 4191:2014 is also applicable to components for the conveyance of water up to and including 45 °C. For temperatures between 25 °C and 45 °C, Figure 1 of ISO 1452‑2:2009 applies. In addition, recommendations are given for the connection to fittings, valves, and ancillary equipment made from materials other than PVC.

  • Technical report
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical report
    44 pages
    English language
    sale 15% off
ISO
ISO 1452-1:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General

ISO 1452-1:2009 specifies the general aspects of unplasticized poly(vinyl chloride) (PVC‑U) solid-wall piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. In conjunction with ISO 1452-2, ISO 1452-3, ISO 1452-4 and ISO 1452-5, it is applicable to PVC‑U pipes, fittings, valves and ancillary equipment, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following: - water mains and services buried in the ground; - conveyance of water above ground for both outside and inside buildings; - buried and above ground drainage and sewerage under pressure. It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Standard
    12 pages
    Russian language
    sale 15% off
ISO
ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to. In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following: - water mains and services buried in ground; - conveyance of water above ground for both outside and inside buildings; - buried and above-ground drainage and sewerage under pressure. It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Standard
    12 pages
    Russian language
    sale 15% off
ISO
ISO 1452-3:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings

ISO 1452-3:2009 specifies the characteristics of fittings made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to. In conjunction with ISO 1452-1, ISO 1452-2 and ISO 1452-5, it is applicable to PVC‑U fittings and to joints with components of PVC‑U, other plastics and non-plastics materials intended to be used for the following: - water mains and services buried in the ground; - conveyance of water above ground for both outside and inside buildings; - buried and above ground drainage and sewerage under pressure. It is applicable to fittings in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    37 pages
    English language
    sale 15% off
  • Standard
    37 pages
    English language
    sale 15% off
  • Standard
    39 pages
    French language
    sale 15% off
  • Standard
    50 pages
    Russian language
    sale 15% off
ISO
ISO 1452-2:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes

ISO 1452-2:2009 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to. In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC‑U pipes without a socket and pipes with a socket (integral or not), intended to be used for the following: - water mains and services buried in the ground; - conveyance of water above ground for both outside and inside buildings; - buried and above ground drainage and sewerage under pressure. It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to pipes for the conveyance of water and waste water up to and including 45 °C and to a range of pipe sizes and pressure classes. It gives requirements concerning colours.

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    23 pages
    French language
    sale 15% off
  • Standard
    26 pages
    Russian language
    sale 15% off