ISO 17419:2018/Amd 1:2024
(Amendment)Intelligent transport systems — Cooperative systems — Globally unique identification — Amendment 1: Regions of a closed polygon in a plane
Intelligent transport systems — Cooperative systems — Globally unique identification — Amendment 1: Regions of a closed polygon in a plane
Systèmes intelligents de transport — Systèmes coopératifs — Identification unique au niveau global — Amendement 1: Régions d'un polygone fermé dans un plan
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17419
First edition
2018-05
AMENDMENT 1
Intelligent transport systems —
Cooperative systems — Globally
unique identification
AMENDMENT 1: Regions of a closed
polygon in a plane
Systèmes intelligents de transport — Systèmes coopératifs —
Identification unique au niveau global
AMENDEMENT 1: Régions d'un polygone fermé dans un plan
PROOF/ÉPREUVE
Reference number
ISO 17419:2018/Amd.1:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 17419:2018/Amd.1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
PROOF/ÉPREUVE © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 17419:2018/Amd.1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO [had/had not] received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC
278, Intelligent transport systems, in accordance with the Agreement on technical cooperation between
ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iii
© ISO 2023 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 3 ----------------------
ISO 17419:2018/Amd.1:2023(E)
Intelligent transport systems — Cooperative systems —
Globally unique identification
AMENDMENT 1: Regions of a closed polygon in a plane
6.9.4
Insert after the bullet list the following paragraph:
The definition of regions, i.e. areas, associated with a closed polygon, shall be as specified in
Annex C.
Annex C
Add the following annex after Annex B, before the Bibliography:
1
© ISO 2023 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 4 ----------------------
ISO 17419:2018/Amd.1:2023(E)
Annex C
(normative)
Closed polygons and their associated regions
C.1 Closed polygon in a two-dimensional Euclidean space
A closed polygon in a two-dimensional Euclidean (or flat) space is an object consisting of an ordered set
of N>2 straight line segments, referred to as edges E , (i = 1, …, N), or sides, connected such that no two
i
segments intersect (or cross), and such that the first and
...
ISO/TC 204/SC
Date: 2023-09-20
ISO 17419:2018/DAMPRF Amd 1
ISO/TC 204/SC /WG 18
Secretariat: ANSI
Date: 2023-11-09
Intelligent transport systems — Cooperative systems — Globally
unique identification
AMENDMENT 1 : Regions of a closed polygon in a plane
Systèmes intelligents de transport -- — Systèmes coopératifs --— Identification unique au niveau global
---------------------- Page: 1 ----------------------
COPYRIGHT PROTECTED DOCUMENT
AMENDEMENT 1: Régions d'un polygone fermé dans un plan
PROOF
---------------------- Page: 2 ----------------------
ISO 17419:2018/PRF Amd 1(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. Phone: + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail: copyright@iso.org
www.iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2023 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 17419:2018/PRF Amd 1(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of
(a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO [had/had not] received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for
identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC
278, Intelligent transport systems, in accordance with the Agreement on technical cooperation between
ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at
www.iso.org/members.htmlwww.iso.org/members.html.
iv © ISO 2023 – All rights reserved
---------------------- Page: 4 ----------------------
DRAFT AMENDMENT ISO 17419:2018/DAM 1:2023(E)
Intelligent transport systems — Cooperative systems — Globally
unique identification
AMENDMENT 1: Regions of a closed polygon in a plane
6.9.4
Insert after the bullet list the following paragraph:
The definition of regions, i.e. areas, associated with a closed polygon, shall be as specified in Annex C.
Annex C
Add the following annex after Annex B, before the Bibliography:
© ISO 2023 – All rights reserved
1
---------------------- Page: 5 ----------------------
ISO 17419:2018/PRF Amd 1(E)
Annex CAnnex C
(normative)
Closed polygons and their associated regions
C.1.C.1 Closed polygon in a two-dimensional Euclidean space
A closed polygon in a two-dimension
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.