ISO 6550-4:2009
(Main)Road vehicles — Sheath-type glow-plugs with conical seating and their cylinder head housing — Part 4: M8 x 1 glow-plugs
Road vehicles — Sheath-type glow-plugs with conical seating and their cylinder head housing — Part 4: M8 x 1 glow-plugs
ISO 6550-4:2009 specifies the main characteristics of M8 x 1 sheath-type glow-plugs with conical seating and their cylinder head housing, for use with diesel (compression-ignition) engines.
Véhicules routiers — Bougies de préchauffage à fourreau et à siège conique, et leur logement dans la culasse — Partie 4: Bougies M8 x 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 6550-4
Second edition
2009-11-01
Road vehicles — Sheath-type glow-plugs
with conical seating and their cylinder
head housing —
Part 4:
M8 × 1 glow-plugs
Véhicules routiers — Bougies de préchauffage à fourreau et à siège
conique et leur logement dans la culasse —
Partie 4: Bougies M8 × 1
Reference number
ISO 6550-4:2009(E)
©
ISO 2009
---------------------- Page: 1 ----------------------
ISO 6550-4:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6550-4:2009(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Dimensions and tolerances.1
3.1 General .1
3.2 Glow-plugs .1
3.3 Cylinder head housing.5
3.4 Threads.6
3.5 Dimension limits of threads M8 × 1 .6
4 Installation tightening torque.7
Annex A (informative) M8 × 1 glow-plugs with 10 mm hexagon and their cylinder head housing .8
Bibliography.10
© ISO 2009 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 6550-4:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6550-4 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 1, Ignition
equipment.
This second edition cancels and replaces the first edition (ISO 6550-4:2005), which has been technically
revised.
ISO 6550 consists of the following parts, under the general title Road vehicles — Sheath-type glow-plugs with
conical seating and their cylinder head housing:
⎯ Part 1: M14 × 1,25 glow-plugs
⎯ Part 2: M12 × 1,25 glow-plugs
⎯ Part 3: M10 glow-plugs
⎯ Part 4: M8 × 1 glow-plugs
iv © ISO 2009 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6550-4:2009(E)
Road vehicles — Sheath-type glow-plugs with conical seating
and their cylinder head housing —
Part 4:
M8 × 1 glow-plugs
1 Scope
This part of ISO 6550 specifies the main characteristics of M8 × 1 sheath-type glow-plugs with conical seating
and their cylinder head housing, for use with diesel (compression-ignition) engines.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.