ISO 16132:2016

Ductile iron pipes and fittings — Seal coats for cement mortar linings

ISO 16132:2016 specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings. It provides the performance requirements for short-term sealing efficiency, long-term durability and cyclic pressure, as well as the routine testing requirements for visual appearance, coating thickness and adhesion. ISO 16132:2016 is applicable to products for potable and other water applications.

Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements de mortier de ciment

General Information

• Status: Withdrawn
• Publication Date: 20-Apr-2016
• ICS: 23.040.10 - Iron and steel pipes
• ICS: 77.140.75 - Steel pipes and tubes for specific use
• Technical Committee: ISO/TC 5/SC 2 - Cast iron pipes, fittings and their joints
• Drafting Committee: ISO/TC 5/SC 2 - Cast iron pipes, fittings and their joints
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 08-Mar-2024

Relations

• Revised: ISO 16132:2024 - Ductile iron pipes and fittings — Seal coats for cement mortar linings
• Effective Date: 06-Aug-2022
• Revises: ISO 16132:2004 - Ductile iron pipes and fittings — Seal coats for cement mortar linings
• Effective Date: 07-Dec-2013

Standards Content (Sample)

DRAFT INTERNATIONAL STANDARD
ISO/DIS 16132
ISO/TC 5/SC 2 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2015-09-02 2015-12-02
Ductile iron pipes and fittings — Seal coats for cement
mortar linings
Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements de mortier de ciment
ICS: 77.140.75; 23.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 16132:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

---------------------- Page: 1 ----------------------
ISO/DIS 16132:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 16132
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Performance test requirements . 2
4.1 Short term sealing efficiency . 2
4.2 Long term efficiency . 2
4.3 Cyclic pressure . 2
5 Routine Test Requirements . 3
5.1 General . 3
5.2 Visual appearance . 3
5.3 Coating thickness . 3
5.4 Adhesion . 3
6 Marking . 3
Annex A (normative) Short term sealing efficiency . 4
A.1 Principle. 4
A.2 Materials and apparatus . 4
A.3 Apparatus . 4
A.4 Preparation of test samples . 4
A.5 Procedure .
...

INTERNATIONAL ISO
STANDARD 16132
Second edition
2016-05-01
Ductile iron pipes and fittings — Seal
coats for cement mortar linings
Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements
de mortier de ciment
Reference number
ISO 16132:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 16132:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16132:2016(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Performance test requirements . 2
4.1 Short-term sealing efficiency . 2
4.2 Long-term sealing efficiency . 2
4.3 Cyclic pressure . 2
5 Routine test requirements . 3
5.1 General . 3
5.2 Visual appearance . 3
5.3 Coating thickness . 3
5.4 Adhesion . 3
6 Marking . 3
Annex A (normative) Short-term sealing efficiency . 4
Annex B (normative) Long-term sealing efficiency . 6
Annex C (normative) Cyclic pressure test .10
Annex D (normative) Coating thickness measurement using test film .12
Annex E (normative) Adhesion tes
...