ISO 13583-2:2015
(Main)Centrifugally cast steel and alloy products — Part 2: Heat-resistant materials
Centrifugally cast steel and alloy products — Part 2: Heat-resistant materials
ISO 13583-2:2015 specifies cast steel and nickel alloy grades for elevated temperature service products manufactured by centrifugal casting.
Produits en acier et alliages moulés par centrifugation — Partie 2: Aciers moulés réfractaires
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13583-2
Second edition
2015-09-15
Centrifugally cast steel and alloy
products —
Part 2:
Heat-resistant materials
Produits en acier et alliages moulés par centrifugation —
Partie 2: Aciers moulés réfractaires
Reference number
ISO 13583-2:2015(E)
©
ISO 2015
---------------------- Page: 1 ----------------------
ISO 13583-2:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13583-2:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 General technical delivery conditions. 1
4 Heat treatment . 1
5 Chemical composition . 1
6 Mechanical properties . 1
7 Supplementary requirements . 1
8 Additional information . 2
Annex A (informative) Mean values for 1 % elongation and creep rupture.5
Annex B (informative) Table of physical properties (Table B.1) . 7
Annex C (informative) UNS cast grades similar to ISO cast grades . 8
Bibliography . 9
© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 13583-2:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO Technical Committee ISO/TC 17, Steel, Subcommittee
SC 11, Steel castings.
ISO 13583 consists of the following parts, under the general title Centrifugally cast steel and alloy products:
— Part 1: General testing and tolerances
— Part 2: Heat resistant materials
This second edition cancels and replaces the first edition (ISO 13583-2:2003), which has been
technically revised with the following changes:
— Clause 2, standard references added where appropriate;
— Table 1, composition limits modified for various grades;
— Tables 1, 2, 3, A.1, A.2, A.3, and B.1;
— Annex C is added.
iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 13583-2:2015(E)
Centrifugally cast steel and alloy products —
Part 2:
Heat-resistant materials
1 Scope
This part of ISO 13583 specifies cast steel and nickel alloy grades for elevated temperature service
products manufactured by centrifugal casting.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 4990, Steel castings — General technical delivery conditions
ISO 13583-1, Centrifugally cast steel and alloy products — Part 1: General testing and tolerances
3 General technical delivery conditions
Cast steel and alloy grades specified by this International Standard shall conform to the applicable
requirements of ISO 4990 and ISO 13583-1 including the supplementary requirements that are
indicated in the enquiry and purchase order.
4 Heat treatment
The cast steel and alloy grades specified by this International Standard do not require heat treatment. If
heat treatment is required, the treatment shall be established by agreement between the manufacturer
and the purchaser, and shall be specified in the purchase contract.
5 Chemical composition
The cast steel and nickel alloy grades shall conform to the chemical composition listed in Table 1.
6 Mechanical properties
The cast steel and nickel alloy grades shall conform to the requirements given in Tables 2 and 3.
Mechanical tests at room temperature and elevated temperature shall be performed if agreed upon
between the manufacturer and purchaser at the time of enquiry and order.
7 Supplementary requirements
A list of supplementary requirements for use at the option of the purchaser is included in ISO 4990
and ISO 13583-1. These supplementary requirements may be used with this specification upon
agreement between the manufacturer and purchaser. These must be agreed at the time of the order
and listed in the order.
© ISO 2015 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 13583-2:2015(E)
8 Additional information
Additional information on the cast steels and nickel alloy grades in this International Standard is
included in Tables A.1, A.2, A.3, B.1 and C.1. This information is given for guidance only and is not a
requirement of this International Standard.
NOTE Annex C gives information on ISO grade designation and available UNS numbers which are similar to
the ISO grade designation.
2 © ISO 2015 – All rights reserved
---------------------- Page: 6 ----------------------
ISO 13583-2:2015(E)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.