ISO 13583-2:2003

Centrifugally cast steel and alloy products — Part 2: Heat resistant materials

ISO 13583-2:2003 specifies cast steel and alloy grades for elevated temperature service pieces manufactured by centrifugal casting.

Produits en acier et alliages moulés par centrifugation — Partie 2: Aciers moulés réfractaires

General Information

• Status: Withdrawn
• Publication Date: 07-Sep-2003
• Withdrawal Date: 07-Sep-2003
• ICS: 77.140.80 - Iron and steel castings
• Technical Committee: ISO/TC 17/SC 11 - Steel castings
• Drafting Committee: ISO/TC 17/SC 11 - Steel castings
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 08-Sep-2015

Relations

• Revised: ISO 13583-2:2015 - Centrifugally cast steel and alloy products — Part 2: Heat-resistant materials
• Effective Date: 12-Feb-2011

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13583-2
First edition
2003-09-15
Corrected version
2004-11-01



Centrifugally cast steel and alloy
products —
Part 2:
Heat resistant materials
Produits en acier et alliages moulés par centrifugation —
Partie 2: Aciers moulés réfractaires





Reference number
ISO 13583-2:2003(E)
©
ISO 2003

---------------------- Page: 1 ----------------------
ISO 13583-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 2 ----------------------
ISO 13583-2:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 General technical delivery conditions. . 1
4 Heat treatment . 1
5 Chemical requirements . 1
6 Mechanical properties . 1
7 Supplementary requirements. . 4
8 Additional information. 4
Annex A (informative) Mean values for 1 % elongation and creep rupture. 5
Annex B (informative) Physical properties . 7

© ISO 2003 — All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 13583-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13583-2 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 11, Steel castings.
ISO 13583 consists of the following parts, under the general title Centrifugally cast steel and alloy products:
 Part 1: General testing and tolerances
 Part 2: Heat resistant materials
This corrected version of ISO 13583-2:2003 incorporates the following corrections.
Clause 2, normative reference to ISO 4990 has been updated.
Table 1, row 17, column 13 (C + N = 0,20 max.).
Table 2, row 12, column 1 (GX42NiCrWSi35-25-5).
Table 3, row 11, column 1 (GX42NiCrSiNbTi35-25).
Table A.1, row 7, column 1 (GX40NiCrSi38-18).
Table A.3, row 13, column 1 (GX42NiCrSiNbTi45-35).

iv © ISO 2003 — All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 13583-2:2003(E)

Centrifugally cast steel and alloy products —
Part 2:
Heat resistant materials
1 Scope
This part of ISO 13583 specifies cast steel and alloy grades for elevated temperature service pieces
manufactured by centrifugal casting.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4990:2003, Steel castings — General technical delivery requirements
ISO 13583-1:2000, Centrifugally cast steel and alloy products — Part 1: General testing and tolerances
3 General technical delivery conditions
Cast steel and alloy grades specified by this International Standard shall conform to the applicable
requirements of ISO 4990 and ISO 13583-1 including the supplementary requirements that are indicated in
the enquiry and purchase order.
4 Heat treatment
The cast steel and alloy grades specified by this International Standard do not require heat treatment. If heat
treatment is required, the treatment shall be established by mutual agreement between the manufacturer and
the purchaser, and shall be specified in the purchase contract.
5 Chemical requirements
The cast steels and alloy grades shall conform to the chemical requirements listed in Table 1.
6 Mechanical properties
The cast steel and alloy grades shall conform to the requirements given in Tables 2 and 3.
Mechanical tests at room temperature and elevated temperature shall be performed if agreed upon between
the manufacturer and purchaser at the time of enquiry and order.
© ISO 2003 — All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 13583-2:2003(E)
Table 1 — Chemical composition (cast analysis % by mass)
P S Mo
Designation Others
C Si Mn Cr Ni Nb W Co
max. max. max.
0,25 1,30 0,50 18,0 8,0
GX30CrNiSi19-9 0,03 0,03 0,5
0,35 1,80 1,50 20,0 10,0
0,35 1,00 0,50 24,0 11,0
GX40CrNiSi25-12 0,03 0,03 0,5
0,45 2,00 1,50 26,0 13,0
0,38 1,00 0,50 24,0 19,0
GX42CrNiSi25-20 0,0
...