ISO 6721-5:1996/Amd 1:2007

Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method — Amendment 1

Plastiques — Détermination des propriétés mécaniques dynamiques — Partie 5: Vibration en flexion — Méthode hors résonance — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 14-Jan-2007
• Withdrawal Date: 14-Jan-2007
• ICS: 83.080.01 - Plastics in general
• Technical Committee: ISO/TC 61/SC 2 - Mechanical behavior
• Drafting Committee: ISO/TC 61/SC 2 - Mechanical behavior
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 17-Apr-2019

Relations

• Revised: ISO 6721-5:2019 - Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method
• Effective Date: 28-Jan-2017
• Amends: ISO 6721-5:1996 - Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method
• Effective Date: 06-Jun-2022
• Child: ISO 6721-5:1996 - Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method
• Effective Date: 15-Apr-2008
• Consolidated By: ISO/TR 16178:2012 - Footwear — Critical substances potentially present in footwear and footwear components
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6721-5
First edition
1996-05-15
AMENDMENT 1
2007-02-01
Plastics — Determination of dynamic
mechanical properties —
Part 5:
Flexural vibration ― Non-resonance
method
AMENDMENT 1
Plastiques — Détermination des propriétés mécaniques dynamiques —
Partie 5: Vibration en flexion ― Méthode hors résonance
AMENDEMENT 1




Reference number
ISO 6721-5:1996/Amd.1:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 6721-5:1996/Amd.1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6721-5:1996/Amd.1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft Int
...