ISO 6362-3:2012

Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 3: Extruded rectangular bars — Tolerances on shape and dimensions

This part of ISO 6362 specifies the tolerances on dimensions and shape of wrought aluminium and aluminium alloy extruded rectangular bars, having thicknesses in the range from 2 mm up to 240 mm and widths in the range from 10 mm up to 600 mm. It applies to extruded rectangular bars.

Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 3: Barres rectangulaires filées — Tolérances sur forme et dimensions

General Information

• Status: Withdrawn
• Publication Date: 21-Jun-2012
• ICS: 77.150.10 - Aluminium products
• Technical Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Drafting Committee: ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 01-Jul-2022

Relations

• Revised: ISO 6362-3:2022 - Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 3: Tolerances on form and dimensions for extruded rectangular bars
• Effective Date: 23-Apr-2020
• Revises: ISO 6362-3:2001 - Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 3: Extruded rectangular bars — Tolerances on shape and dimensions
• Effective Date: 28-Feb-2009

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6362-3
Third edition
2012-07-01
Wrought aluminium and aluminium
alloys — Extruded rods/bars, tubes and
profiles —
Part 3:
Extruded rectangular bars — Tolerances
on shape and dimensions
Aluminium et alliages d’aluminium corroyés — Barres, tubes et
profilés filés —
Partie 3: Barres rectangulaires filées — Tolérances sur forme et dimensions
Reference number
ISO 6362-3:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 6362-3:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6362-3:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3  Terms and definitions . 1
4 Materials . 1
5 Tolerances on shape and dimensions . 2
5.1 Dimensional tolerances . 2
5.2 Shape tolerances . 3
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6362-3:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6362-3 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee
SC 6, Wrought aluminium and aluminium alloys.
This third edition cancels and replaces the second edition (ISO 6362-3:2001), which has been technically revised.
ISO 6362 consists of the following parts, under the general title Wrought aluminium and aluminium alloys —
Extruded rods/bars, tubes and profiles:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Mechanical properties
— Part 3: Extruded rectangular bars — Tolerances on shape and dimensions
— Part 4: Profiles — Tolerances on shape and dimensions
— Part 5: Round, square and hexagonal bars — Tolerances on shape and dimensions
— Part 6: Round, square, rectangular and hexagonal tubes — Tolerances on shape and dimensions
— Part 7: Chemical composition
iv © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6362-3:2012(E)
Wrought aluminium and aluminium alloys — Extruded rods/
bars, tubes and profiles —
Part 3:
Extruded rectangular bars — Tolerances on shape and dimensions
1 Scope
This part of ISO 6362 specifies the tolerances on dimensions and shape of wrought aluminium and aluminium
alloy extruded rectangular bars, having thicknesses in the range from 2 mm up to 240 mm and widths in the
range from 10 mm up to 600 mm.
It applies to extruded rectangular bars.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 6362-1, Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1:
Technical conditions for inspection and delivery
3  Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6362-1 apply.
4 Materials
For the purposes of this part of ISO 6362, wrought aluminium and aluminium alloys are divided into two groups,
which correspond to varying difficulty when manufacturing the products.
The division into Group I and Group II of the most commonly used general engineering alloys is specified in Table 1.
Grouping of other alloys is subject to agreement between the purchaser and supplier.
Table 1 — Alloy group
1070, 1070A, 1060, 1050, 1050A, 1350, 1100, 1200
3102, 3003, 3103
Group I
5005, 5005A, 5051A, 5251
6101, 6101A, 6101B, 6005, 6005A, 6005C, 6110A, 6012, 6018, 6023, 6351, 6060, 6360, 6061,
6261, 6262, 6262A, 6063, 6063A, 6463, 6065, 6081, 6082, 6182
2007, 2011, 2011A, 2014, 2014A, 2017, 2017A, 2024, 2030
Group II 5019, 5049,5052, 5154A, 5454, 5754, 5056, 5083, 5086
7003, 7204, 7005, 7108, 7108A, 7020, 7021, 7022, 7049A, 7050, 7075
NOTE The four-digit numbers listed are taken from the Registration of International Alloy Designations and Chemical Composition
Limits for Wrought Aluminium Alloys, published by the Aluminum Association, 1525 Wilson Boulevard, Suite 600, Arlington, VA 22209,
USA (known as “Teal Sheets”).
© ISO 2012 – All rights reserved 1

--------------------
...