Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 5: Round, square and hexagonal bars — Tolerances on shape and dimensions

This part of ISO 6362 specifies the tolerances on dimensions and shape of the following: — wrought aluminium and aluminium alloy extruded round bars, having diameters in the range from 8 mm up to 350 mm; — wrought aluminium and aluminium alloy extruded square and hexagonal bars, having widths across flats in the range from 10 mm up to 220 mm. It applies to extruded round, square and hexagonal bars.

Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 5: Barres rondes, carrées et hexagonales — Tolérances sur forme et dimensions

General Information

Status
Withdrawn
Publication Date
21-Jun-2012
Current Stage
9599 - Withdrawal of International Standard
Completion Date
01-Jul-2022
Ref Project

Relations

Buy Standard

Standard
ISO 6362-5:2012 - Wrought aluminium and aluminium alloys -- Extruded rods/bars, tubes and profiles
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6362-5
Third edition
2012-07-01
Wrought aluminium and aluminium
alloys — Extruded rods/bars, tubes and
profiles —
Part 5:
Round, square and hexagonal bars —
Tolerances on shape and dimensions
Aluminium et alliages d’aluminium corroyés — Barres, tubes et
profilés filés —
Partie 5: Barres rondes, carrées et hexagonales — Tolérances sur
forme et dimensions
Reference number
ISO 6362-5:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 6362-5:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6362-5:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3  Terms and definitions . 1
4 Materials . 1
5 Tolerances on dimensions . 2
5.1  Tolerances on diameter and width across flats . 2
5.2 Circularity of round bars . 2
5.3 Corner radii of square and hexagonal bars . 2
5.4 Fixed-length tolerances . 3
5.5 Squareness of cut ends . 3
6 Tolerances on shape . 3
6.1 General . 3
6.2 Straightness tolerances . 3
6.3 Convexity/concavity . 4
6.4 Twist tolerances . 4
6.5 Squareness for square bars . 5
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6362-5:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6362-5 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee
SC 6, Wrought aluminium and aluminium alloys.
This third edition cancels and replaces the second edition (ISO 6362-5:2001), which has been technically revised.
ISO 6362 consists of the following parts, under the general title Wrought aluminium and aluminium alloys —
Extruded rods/bars, tubes and profiles:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Mechanical properties
— Part 3: Extruded rectangular bars — Tolerances on shape and dimensions
— Part 4: Profiles — Tolerances on shape and dimensions
— Part 5: Round, square and hexagonal bars — Tolerances on shape and dimensions
— Part 6: Round, square, rectangular and hexagonal tubes — Tolerances on shape and dimensions
— Part 7: Chemical composition
iv © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6362-5:2012(E)
Wrought aluminium and aluminium alloys — Extruded rods/
bars, tubes and profiles —
Part 5:
Round, square and hexagonal bars — Tolerances on shape
and dimensions
1 Scope
This part of ISO 6362 specifies the tolerances on dimensions and shape of the following:
— wrought aluminium and aluminium alloy extruded round bars, having diameters in the range from 8 mm
up to 350 mm;
— wrought alumin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.